泵基座 的英文怎麼說
中文拼音 [bèngjīzuò]
-
Diesel engines - base - mounted in - line fuel injection pumps and high - pressure supply pumps for common rail fuel injection systems - mounting dimensions
柴油機.共軌燃料噴射系統用
基座安裝直列式噴油
泵和高壓供油
泵.安裝尺寸
-
Diesel engines - mounting dimensions of fuel injection pumps - part 2 : base - mounted in - line pumps and high - pressure supply pumps for common rail fuel injection systems
柴油發動機.噴油
泵的安裝尺寸.第2部分:公軌燃料噴射系統用
基座安裝直列多柱塞
泵和高壓供給
泵
-
Rebar and anchor bolts used in the pump base shall be sufficiently tied to the mounting floor to ensure a rigid, stable mounting surface for the pump unit
泵基座所採用的鋼筋和錨固螺栓應該能夠與安裝地面結合牢固緊密,確保為
泵設備提供堅固可靠的安裝
基礎。
-
The height of the base shall be sufficient so that the centerline of the suction elbow lines up with the centerline of the suction piping and shall include an allowance for grouting between the concrete base and the pump mounting pedestal in accordance with the pump manufacturer ' s recommendations
根據
泵製造商的建議,
泵基座應該有足夠的高度,使得吸入彎頭的中心線能夠與吸入管道中心線連接起來,混凝土
基座與
泵安裝
基座之間有足夠的空間用於灌漿。
-
Five floating roof oil tanks with volume 2 104m3 are designed to be constructed at shuguang pump station possessed by liaohe oil field, which is located at liaohe delta alluvial plain. this engineering filed is featured with complicated topography. the oil tank foundation soil is horizontally - layered, including four layers : medium dense - dense clay, interbedding of find sand and clay, fine sand sandwiching clay and fine sand
位於遼河三角洲沖積平原的遼河油田曙光
泵站計劃增建5
座2 10 ~ 4m ~ 3浮頂式儲油罐,場區地形復雜,油罐地
基土層分佈均勻水平,從上之下主要由中密粉土層、粉細砂與粘土互層、粉細砂夾粘土層和細砂層等4層組成。
-
The support pedestal shall be designed for anchor bolting to a concrete foundation and shall be of adequate strength and mass to support the combined weight of the pump / motor assembly and all forces imposed by the pump unit during operation
支撐
基座應該採用錨固螺栓固定在混凝土
基座上,應該具有適當強度和質量,能夠支撐
泵/電機總裝的總重量,以及
泵設備在運行過程中所產生的所有壓力。
-
The contractor shall provide a concrete pump - mounting base for each pump as shown in the plans
根據說明書的要求,承包商應該負責為每臺
泵配置一個混凝土
泵安裝
基座。
-
The base shall be of adequate height to provide suitable clearance between the pump suction elbow and the mounting floor and of sufficient strength to accept all forces imposed by the pump unit
這個
基座應該具有適當的高度,使得
泵吸入彎頭與安裝地面具有適當的間隙,並有足夠的強度承受
泵設備所產生的所有壓力。
-
Iso 3661 : 1977 ; end - suction centrifugal pumps - baseplate and installation dimensions iso 3661 : 1977 ; german version en 23661 : 1993
離心式末端吸入
泵.
基座和安裝尺寸
-
A support pedestal for mounting of the complete pump / motor assembly shall be provided and shall be constructed of fabricated steel
應該提供用於安裝泵/電機總裝的支撐基座,其結構材料應該採用預制鋼。