泵浦腔 的英文怎麼說

中文拼音 [bèngpǔqiāng]
泵浦腔 英文
pumcavity
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 浦 : 1. （水邊或河流入海的地方, 多用於地名） riverside; river mouth2. （姓氏） a surname
  • 腔 : 名詞1. （動物體內空的部分） cavity; chamber 2. （話） speech 3. （樂曲的調子） tune; pitch 4. （說話的腔調） accent; tone
  1. Under the incentive of the civil - market demanding such as laser material processing and the military - market demanding such as a new generation of laser weapon candidate and icf, diode - pumped solid laser ( dpsl ) develops rapidly worldwide. as an important application, diode - pumped intracavity - frequency - doubled laser is attached much importance in recent years, but there still remain many problems unresolved completely. in this paper, i have given some abecedarian study results on some of these problems theoretically and experimentally

    因工業激光材料加工等民用市場的需求以及慣性約束聚變和作為新一代激光武器候選器件等軍方需求的推動，國際上高功率二極體泵浦固體激光器（ dpsl ）的研究進展迅速，作為dpsl的一個重要應用，內腔倍頻一直得到大家的重視，但仍有許多未徹底解決的問題和理論上的不完備之處，本論文擬對其中的一些問題作一初步的理論和實驗研究。
  2. The experiment of intracavity doubling of a 946 nm nd : yag laser with an lbo crystal has been done at room temperature. a continuous wave 473 nm laser is obtained with 235mw output power at a pump power of 20w. the laser beam quality of 473 nm is good as well

    對腔內倍頻輸出473nm激光進行了初步的實驗研究，在泵浦功率為20w時， l獲得了光束質量較好的連續波形式的藍光激光輸出，其功率為200mw 。
  3. According to the guidline, two nd : yag lasers have been designed and set up, one is end - pumped by lower output power ld using a selfoc micro lens, and the other is end - pumped by high output power ld using a pair of lenses are designed, and the characteristics such as output power and power stabilization of both solid - state lasers are investigated. thirdly, when an empty liquid crystal cell is inserted in the cavity of the nd : yag laser pumped by high power ld, the laser can operates in single axial mode. finally, according to the relationship between the laser output power and the longnitudinal a ld - end - pumped nd : yag laser sensor for displacement measurement has been investigated theoretically and demonstrated experimently, the results indicate that when the mean radius of pumping inside the laser cavity is far less than that of the oscilating laser mode, the exponential of the output power is a gauss function of the longitudinal positon of focused spot of ld pumping beam, both the measurement range and the sensitivity are dependent on the incident pumping power, as the incident pumping power is increased, the measurement range is enlarged and the sensitivity is improve d

    本文首先介紹了ld泵浦nd ： yag激光器的發展狀況、主要特性及其應用，從四能級速率方程出發，推導了ld泵浦nd ： yag激光器的閾值、輸出功率和斜效率的表達式，並簡述了激光器的工作原理、結構型式和倍頻方法；其次，以空間相關的速率方程為基礎，提出了ld端面泵浦nd ： yag激光器的設計方法，給出了一定泵浦耦合方式下，振蕩光模尺寸、最佳輸出耦合率、泵浦光模尺寸、泵浦光焦斑位置等參數的選取依據，以此為依據，設計了自聚焦透鏡耦合小功率ld泵浦nd ： yag激光器和透鏡組耦合高功率ld泵浦nd ： yag激光器，對激光器的輸出功率和功率穩定性等特性進行了實驗研究；再次，在帶尾纖輸出的高功率ld泵浦nd ： yag激光腔內插入一隻空液晶盒，觀察到了激光器以單縱模運轉；最後，根據泵浦光焦斑端面位置對激光輸出功率的影響規律，提出了ld端面泵浦nd ： yag激光位移傳感新方法，並進行了理論和實驗研究，研究結果表明：當激光晶體內泵浦光平均光斑半徑遠小於振西安理工大學碩士學位論文蕩光束腰半徑時，激光輸出功率的自然指數與泵浦光焦斑的縱向位置成高斯變化規律，測量范圍和靈敏度依賴于泵浦功率，隨著泵浦功率的增加，測量范圍擴大，靈敏度提高，當端面泵浦功率為7 . 24w （最大輸出功率為1 . 926w ）時，激光位移傳感器的測量范圍和靈敏度分別是13 . 045mm和0 . 148mw / pm 。
  4. All - solid - state laser is an advantage lamp - house. it has many important applications and potential commercial value in many fields, such as industry, scientific research, military. so it ' s always the research focus of laser field. diode end - pumped solid - state laser has many merits. including high efficiency, long lifetime, high frequency stability, narrow line width, compact configuration, convenient for use et al, which made her a necessity in many high level quantum optics experiments. in this thesis, a series of experiment research was done with regard to blue laser, green laser and infrared laser

    激光二極體端面泵浦的固體激光器具有效率高、譜線窄、壽命長、結構簡單、使用方便等優點，特別是採用環行諧振腔內加光學單向器構成的單頻激光器，由於頻率穩定，使其成為許多高水平量子光學實驗的主要光源。本論文圍繞全固態單頻藍，綠，紅外激光器進行了一系列實驗研究工作。
  5. We presents a detailed studied of the linewidth of parametric light in clbo - opo caused by the linewidth of pumping beam, off axis phase matching, divergence angle of pumping, time above threshold, high gain coefficient of nlo crystal, fluctuate of cavitylength, spontaneous radiation, according to the momentum and energy conversion laws, and the sellmeier equations of the clbo, we calculated curves of the type - i and type - ii compared with the bbo ' s

    根據能量動量守恆關系和clbo的色散方程，詳細分析了由於泵浦光的線寬、泵浦光偏軸泵浦、泵浦光的發散角、泵浦光功率超過參量光振蕩閾值一定倍數、高增益系數、有效腔長波動以及自發輻射引起的參量光線寬，並得到了與bbo晶體在類、類相位匹配下比較的理論曲線。
  6. Some researches about frequency doubling are made, and two methods to improve intensity of second frequency generation are given. we realized q - switched 532 nm laser, by using nd : gdvo4 as laser crystal, using cr4 + : yag as saturable absorber, using ktp as intra - cavity frequency doubling crystal. average power of 109mw, repetition of 40khz, pulse width of 30ns, pulse energy of 2. 6uj, peak power of 91w are obtained

    4 .對倍頻理論進行研究和分析:討論兩種提高二次諧波功率密度的方一法;實驗匕在國內首次實現ld端面泵浦nd : gdvo4 / ktp ，用cr4 + : yag作為可飽和吸收片的綠光激光器，腔內倍頻得到了平均功率為109mw 、重復頻率為40khz 、脈寬為3ons 、單脈沖能量為2 . 6閃、峰值功率為glw的調q綠光輸出。
  7. Ba 2 external resonator raman laser excited by 532 nm laser

    激光泵浦硝酸鋇晶體產生外腔拉曼激光
  8. Measuring the intracavity loss of laser. in the theory, we analyze the relation of output power and input power of the different transmission rate of output mirror. using the experiment validated the theory result

    實驗上測量了激光器的內腔損耗，並計算得到在泵浦功率等於2 . 2w時，最佳輸出耦合透射率t _ （ opt ） = 5 . 2 。
  9. 4 ) the tuning characteristics of doubly - resonant optical parametric oscillator propo ) output by changing crystal ' s temperature, opo ' s cavity length and pump frequency respectively are theoretically analyzed and experimental obtained the wavelength of the opo output can be tuned from 2038nm to 2227nm by the crystal ' s temperature changed of 5. 3, from 2044nm to 2219nm by the cavity length changed of 514nm, and 375mhz by the pump frequency continuously tuned 750mhz

    當晶體溫度變化5 . 3時，得到2038nm - 2227nm可調諧下轉換光輸出；當opo的腔長相對于簡並點腔長變化514nm時，得到2044nm - 2219nm可調諧下轉換光輸出：當泵浦光頻率連續的改變了750mhz時，下轉換光的頻率相應連續調諧375mhz 。理論擬合與實驗結果基本一致。
  10. Based on these foundations, we give a perfect scheme of the bbo opos : single pass amplification coefficient of the opg under different pump intensity is calculated ; collinear type - i and type - ii phase matching tuning curve pumped by the q switch nd : yag various harmonics as well as noncollinear type - i tuning curve are calculated in details ; the effect of the walkoff for the nonlinear effect coefficient and the group velocity matching are analyzed ; the acceptance angle in parametric process is calculated ; the numerical threshold of the bbo opo is calculated ; the process of the saturation and depletion of the pump beam are analyzed ; the relationship of the conversion efficiency and reflectance of output mirror are discussed ; various linewidth controlling methods are discussed ; the improvement of the beam quality applying the unstable cavity is discussed ; and the crystal bbo design is considered

    在此基礎上，給出了一整套bbo - opo激光參數設計方案：計算了不同泵浦強度下的參量放大倍數；詳細計算了在nd : yag調q激光器各次諧波泵浦條件下的共線類和類相位匹配的調諧曲線，以及非共線類相位匹配調諧曲線；分析了走離角對非線性系數和群速匹配的影響；計算了參量過程的允許角；計算了bbo - opo的理論閾值條件；分析了飽和與泵浦光束的消耗過程；給出了轉換效率與超過泵浦閾值的倍數的關系；討論了轉換效率與輸出鏡反射率的關系；討論了線寬控制的各種方法；研究了利用非穩腔改善光束質量的方法；考慮了bbo晶體的設計。
  11. Adopting the amendatory rate equation, the threshold of the micro - cavity has been studied and the conclusion is shown as following : if there is not non - radiation transition, the pump velocity just need to compensate the photon velocity escaped from the cavity, and the intensity of output light will direct ratio to the intensity of input light then we got a micro - cavity laser with no threshold

    採用修正的速率方程對微腔激光器的閾值進行研究，得到如下結論：在沒有無輻射躍遷時，激光器的泵浦速率只需恰好補償光子向腔外的逃逸速率，輸出光強隨著輸入泵浦光強性線增加，實現所謂的「無閾值」激光器。
  12. The trends of dpssl are pointed out, the wide application fields, as well as the bright market future of high power dpssl are also summarized. in the chapter 2, all kinds of solid - state laser gain materials are introduced in detail. in the chapter 3, the theory on the mode - matching of the pump beam and the cavity mode is analyzed in detail based on the basic theory and work principle of ld - pumped all - solid - state laser

    本論文第一章從二極體泵浦固體激光器的優勢出發，介紹了二極體泵浦固體激光器的發展，指出了dpssl的發展方向，概括介紹了大功率dpssl的諸多應用領域和廣闊的市場前景；第二章對固體激光增益材料作了詳細的介紹；第三章基於ld泵浦固體激光器的基本理論和工作原理，從理論上詳細分析了ld端面泵浦激光器中泵浦光與腔模的匹配問題。
  13. We use the laser output ( 320 nm, 200 fs ) of optical parametric amplifier ( opa ) in < wp = 5 > an active passive mode - locked femtosecond ti - sapphire laser operating at a repetition rate of 1khz as a exciting resource to develop optically pumped stimulated emission of zno thin films. when rectangular stripe laser irradiates thin films, optical resonant cavity is naturally formed between two nanocrystallites along with the rectangular laser stripe and planar weveguide confines the light scattering

    利用飛秒激光器作為光泵浦激發光源，研究了氧化鋅薄膜的光泵浦受激發射，當條形光斑輻照薄膜樣品時，將沿著光斑條由氧化鋅納米晶面自然地形成光學諧振腔，由於平面介質波導結構限制光散射，所以成功地觀測到二氧化硅襯底上的納米氧化鋅（ zno ）薄膜的紫外受激發射。
  14. If a nd : yag laser runs at high pump power, laser resonator will generate multimode beam due to thermal lens of active rod. the higher pump power is, the bigger divergence occurs and the smaller rayleigh range is

    當nd ： yag激光器工作在高泵浦功率下時，由於nd ： yag激光器工作物質的熱透鏡效應導致了諧振腔輸出多模激光，隨著泵浦功率的升高激光光束發散角增大，焦深減小。
  15. Using large - area - mode yb3 + - doped photonics fiber, we realized laser operation and analyzed its output properties. the laser is cladding pumped and the output power is 2. 6w, with wavelength of 1074. 5 nm and slope - efficiency 54 %

    在選用二色鏡作為激光器后腔鏡的實驗中，在泵浦功率7 . 8w時獲得了2 . 6w激光輸出，波長為1074 . 5nm ，斜率效率為54 % 。
  16. Introducing abcd theory, the laser mode was analyzed ; with thermal effect consideration, a short folded - cavity resonator which was not sensitive to thermal effect was designed. thus, the requirements for efficient doubling frequency were satisfied. 3

    採用標準abcd傳輸矩陣理論，對激光器腔模式進行了詳細的分析，在充分考慮熱效應的前提下，根據實際情況，合理設計出對熱效應不敏感的三鏡折疊腔，產生兩個光腰，既滿足了泵浦光能量的充分利用，也滿足了縮小光腰提高倍頻效率的要求。
  17. Based on the character of the eof gain at 1550 nm, a laser diode ( ld ) worked at 980 nm and acted as the pumping source, a eof employed as gain medium, and a fiber grating used as reflector, an ring - cavity all - fiber laser worked at 1562. 5 nm was demonstrated with an output power of 2. 0 mw and a bandwidth of 0

    本文主要基於摻鉺光纖在1550nm波段的增益特性，利用帶尾纖的980nm半導體激光器作為泵浦源，鉺光纖作為增益介質，布拉格光纖光柵作為諧振腔反射鏡，實現了波長為1562 . 5nm的環形腔光纖激光器，得到了2mw的激光輸出。
  18. The self - q - switched pulses of high erbium - doped fabry - perot cavity fiber laser are observed and theoretically analyzed. ( 2 ). utilizing the non - linearity characteristics of single mode fiber - back stimulated brillouin scattering ( bsbs ) and the wavelength - selecting characteristics of fiber gratings, self - q - switched pulses are achieved from a linear cavity erbium - doped fiber laser pumping by a 980nm ld continue wave ( cw ) pumping, the pulse width is 2. 2ns and the repetition frequency of pulses is 64. 5mhz

    （ 2 ）利用單模光纖的非線性效應背向受激布里淵散射（ bsbs ）和光纖光柵的選頻特性，採用980nm半導體激光器連續泵浦方式，在線性腔摻鉺光纖激光器中實現了自調q運轉，獲得脈沖寬度（ fwhm ）約為2 . 2ns ，重復頻率為64 . 5mhz的穩定的光脈沖輸出。
  19. In the part of the experimental designs, a experimental configuration of an unstable cavity by use of two bbo crystals compensating the walkoff effect and pumped by reflection is presented, and two set of controlling systems designs of open and closed loop are also presented ; we realized closed loop controlling system of bbo optical parametric oscillator tuning system, by using american general scanning inc. ' s controller to control bbo crystal ' s rotation, and scaled the output wavelength with charge coupled device

    在實驗設計上給出了利用兩塊bbo晶體補償走離效應返回式泵浦非穩腔的實驗設計，設計了開環和閉環兩套控制系統。通過使用美國通用掃描公司的掃描頭控制bbo晶體的轉動，用ccd對bbo - opo輸出波長進行標定，實現了bbo - opo調諧系統的閉環控制，相對波長調諧誤差小於0 . 04 ，並給出了354 . 7nm泵浦的類相位匹配bbo - opo輸出波長隨晶體轉角變化的理論和實驗曲線。
  20. Because of high threshold of 946 nm laser, severe thermal lens effect will appear when the 946 nm laser operations. in the consideration of thermal lens effect, the - optimized folding cavity has been devised. the relation between thermal lens effect and the radius of laser beam waist has been given as well

    由於946nm激光閾值很高，需要更強的泵浦功率密度，因此較大功率藍光激光器的熱透鏡效應將會比紅光和綠光激光器更明顯，而熱透鏡效應是影響激光功率提高和激光輸出穩定性的重要原因，所以在考慮到激光晶體熱透鏡效應的情況下，優化設計了折疊腔結構，並給出了熱透鏡效應和折疊腔中腔模半徑大小的關系。
分享友人
分享到 Line

分享到臉書