泵缸體 的英文怎麼說

中文拼音 [bènggāngtǐ]
泵缸體 英文
pumcylinder block
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 缸 : 名詞1. （盛東西的器物） jar; jug; vat; crock 2. （缸瓦） earthenware with crude glaze 3. （像缸的器物） jar-like things
  • 體 : 體構詞成分。
  1. The machine is circumgyration drilling machine that the rotary drives drilling tool to bore by rotation, adopts full hydraulic pressure drive, constant power loop, wheel cylinder startup, oil cylinder disappear ing end bumper, electrohydraulic combined control, steel wheel traveling and disassembly transport

    該機是由轉盤帶動鉆具旋轉鉆進的回轉鉆機，採用全液壓驅動，恆功率迴路，分泵啟動，油缸升降，電液復合操縱，鋼輪行走，解體運輸。
  2. Richard yem sync : under the action of the waves the hydraulic ram ' s blue unit, shown down here on my left, pumps high pressure fluid into these large accumulators

    Richard同步解說:在波的作用下，液壓油缸的藍色單元，在我的左邊，將高壓液體泵入大型蓄電池。
  3. M ) richard yem sync : under the action of the waves the hydraulic ram ' s blue unit, shown down here on my left, pumps high pressure fluid into these large accumulators

    Richard同步解說:在波的作用下，液壓油缸的藍色單元，在我的左邊，將高壓液體泵入大型蓄電池。
  4. Kinematics of the axial piston pump with swash plate yoke ' s angle were analysed. there was a lot of analysis about relative movement between piston and cylinder block, between piston and swash plate, between slipper and swash plate. at same time, the movement simulation curves were given

    對軸向柱塞泵進行運動學分析，重點是對柱塞與缸體之間，柱塞與斜盤之間以及滑靴與斜盤之間的相對運動進行分析，並且分別給出了模擬曲線； 2
  5. Top quality hydraulic pump with welded construction hard chrome plated pistion and pump plunger ensure durability and corrosion resistance

    液壓缸體為優質鋼焊接而成，注塞桿、泵芯鍍硬鉻，耐磨、耐腐蝕。
  6. A method based on the application of an injection process analysis software is introduced in this article, which optimize injection process through changing the design of fuel - injection pump cam. a model of 1115 single cylinder direct injection diesel engine is used as an example. with the help of pre - journey optimization, increasing cam lift and using tangent - function can make the matching of the injection system with the diesel more reasonable. without changing fuel pump installing size, it can enhance injection rate and injection pressure and improve the diesel operating stability in low speed condition

    本文以國產1115型單缸直噴柴油機為例，介紹一種應用噴油過程分析軟體改進噴油泵凸輪設計的方法，通過增大噴油泵凸輪升程、採用切線函數凸輪並優化預行程的方式，在不改變噴油泵安裝尺寸的前提下，可提高噴油壓力和噴油速率，改善柴油機低速工作穩定性，使噴油系統與柴油機匹配更合理。
  7. In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards

    論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。
  8. The company uses the low pressure casting in producing such as gasoline pump body, cylinder head, moto cylinder head and so on other aluminum alloy casting products, which has yearly capability of 3 million aluminum alloy castings and 200, 000 pcs finished products output, and is continuously evaluated as " advanced unit on quality ", " the excellent supplier ", " the high - quality

    公司採用低壓鑄造生產汽車油泵體氣缸蓋摩托氣缸蓋等鋁合金鑄件產品，具有年產300萬件鋁合金鑄件的能力。公司連續多年被主機廠評為「質量先進單位」 「優秀供應商」 「優質服務獎」 。
  9. The water pump transfers piston cylinder crack origin analysis and processing

    水泵轉輪體活塞缸裂紋成因分析及處理
  10. Casting for auto parts ( calliper, bracket, disc, pressure plate etc ), reerigerator and air conditioner compressor parts ( cylinders, crankshaft etc ), machinicalparts, construction parts, motorparts, pump parts etc

    汽車用鑄件（制動鉗體、支架、制動盤、壓盤等） ，機械零件，冰箱、空調壓縮機鑄件（缸體、曲軸等） ，建築工程用鑄件，電機零件，水泵等。
  11. Furthermore, it discusses how to figure out these models mentioned above. with reference to the design of various automobiles, it primary defines the method to get key parameters in platform lorry general design, and creates mathematical model. it provides more reference to choose axis, driving axle, number of arrest axles, type of tire, pump, motor, lift hydrocylinder, maximum payload and sole weight reasonably

    在參考各類汽車設計思想的基礎上，根據理論推導和經驗公式的計算，初步確定了平板車總體設計階段的主要技術參數的求解方法，建立了數學模型，為合理地選擇軸、驅動橋、制動橋個數，輪胎型號、泵、馬達、舉升油缸、平板車的最大載重量和自重的選擇等提供了依據。
  12. The new unit has following technical features : ( 1 ) the unit ' s load is balanced by means of the accumulator and hydraulic cylinder with special structure ; ( 2 ) the installed power of the unit can be reduced greatly by adopting the accumulator ; ( 3 ) variable frequency speed regulation ensures good energy saving effect, and the closed oil circuit requires less hydraulic oil ; ( 4 ) a bi - directional hydraulic lock in the oil circuit ensures the stability and safety of the operation of the pumping unit

    新型機具有4個技術特點： （ 1 ）由於活塞柱塞式液壓缸的特殊結構和液壓蓄能器的配合使用，在平衡抽油機大部分載荷時，不需另外增加配重，可減小抽油機體積、質量和佔地面積； （ 2 ）抽油機下沖程時，與活塞柱塞式液壓缸相連接的蓄能器吸收能量，上沖程時儲存在蓄能器中的能量補充載荷上行所需的能量，大幅度降低抽油機裝機功率； （ 3 ）利用變頻容積調速節能效率高，閉式油路節省液壓油，同時大大減小液壓泵站的體積； （ 4 ）在閉式油路中採用雙向液壓鎖可使抽油機的啟停更加平穩、迅速，其工作的穩定性和安全性更好。
  13. Experimental study on laser cladding valve - plate pair surface of hydraulic pump

    液壓泵缸體配流副表面激光熔覆的實驗研究
  14. At present, usual method of fd is measuring vibration signal as system feature signals for fault characteristic eigenvectors pickups

    故障診斷常用的方法是以泵缸體上的振動信號作為系統特徵信號來提取故障特徵向量。
  15. Abstract : in order to process signal in depth and to extract the fault feature from original signal in machinery diagnosis ， the graphical display algorithm that can keep the data length of wavelet transform results the same as that of original signal is used. the fault diagnosis of a bend axial piston pump via b - spline wavelet that has linear phase is provided. the results of study demonstrate that the new method has excellent feature and the weak fault signal can be extracted from the strong vibration background of the pump

    文摘:採用具有線性相位的b樣條小波，應用圖形顯示演算法並結合小波變換快速演算法將信號分解到不同的頻帶上，且分解結果和原信號長度保持一致，可對信號進行深層次的處理，克服了傳統的信號處理方法不易提取微弱信息的不足.通過對礦用斜軸式柱塞泵振動信號的分析，分離出了配流副磨損、球鉸松動、缸體及泵軸支撐軸承的故障特徵，為液壓泵的故障診斷提供了依據，並為信噪分離、微弱信號提取及設備的早期故障診斷提供了一條有效途徑
  16. The explosive mixture of the petrol engine is provided by a carburettor, but in the case of the diesel engine the supply is effected by an injection or jerk pump which forces a shot of fuel into each cylinder in turn according to the correct firing sequence

    翻譯：汽油發動機由一個化油器輸送可燃混合氣體，而柴油發動機，由一個噴射泵或柱塞式燃油泵實現燃油供應，此泵根據正確的點火順序把少量燃油依次壓入每個汽缸。
  17. Cold water pump cylinder

    冷水泵缸體上蓋
  18. 8. no parts and components warranty will be delivered if such parts and components as body, cylinder cover, cylinder liner, water pump, oil cooler and compressor are cracked in winter, because customer fails to drain water immediately or completely exclusive of case when anti - frozen fluid is used after shutting down the power unit

    因冬季顧客停機時未及時放水，或水未放凈採用防凍液的除外，導致機體缸蓋缸套水泵機油冷卻器空壓機等零部件凍裂，相關零部件不予保修。
  19. Cylinder block vacuum pump pad cover

    汽缸體真空泵墊蓋
  20. Owing to the cylindrical surface of piston and jar hole, radial piston pump can be assembled accurately. compared with the axial piston pump, the radial piston pump is better against impact, moreover, it has longer life, higher cubage efficiency and higher control precision

    由於徑向柱塞泵具有柱塞與缸體內孔均為圓柱面，易達到高精度的配合等結構特點，因此，比軸向柱塞泵耐沖擊、壽命長、容積效率高、控制精度高。
分享友人
分享到 Line

分享到臉書