流量脈動 的英文怎麼說

中文拼音 [liúliángmàidòng]
流量脈動 英文
flow pulsation
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 脈 : 脈名詞1. （動脈和靜脈的統稱） arteries and veins2. （脈搏的簡稱） pulse 3. （像血管的組織; 連貫成系統的東西） vein
  • 流量 : rate of flow; flow; runoff; discharge; throughput; （flow） rate; quantity （of flow）; flux
  • 脈動 : [物理學] [天文學] pulsation; pulsing; pulse; ripple; impulsive motion; pulsating; panting; loping...
  1. If the coefficient of engagement overlap decreases, the flow aggrandize, trapping volume and the flow pulsating ratio decreases

    隨著齒輪嚙合重合系數的減小，齒輪泵的流量增大，困油容積和流量脈動率減小。
  2. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  3. The numerical results show that the time domain response of the laminated plates induced by the in - line force of non - steady component oscillating flow is similar to harmonic motion with certain ribbon which is formed by period motion

    計算結果表明，零均值流量脈動流順流向作用力誘發反對稱角鋪設層合板的時域響應近似於具有一定帶寬的諧波運動，而這一帶寬又是由一定周期運動形成的。
  4. The flow characteristics of the elliptic rotator pump

    擺動活齒泵的流量脈動
  5. The following is the detail design of the pump, and a optimum mathematical model are presented to mostly reduce the helical gear pump flow pulse

    在此基礎上進行了斜齒齒輪泵的結構設計，通過建立斜齒齒輪泵齒輪的優化數學模型，優化計算出使輸出流量脈動最小的斜齒輪參數，製造出斜齒齒輪泵樣機。
  6. 2. the flux characteristics of ordinary helical gear pump are lucubrated by theory for the first time, on this condition the selective qualification of the helical gear pump is gained

    首次對普通斜齒齒輪泵流量特性進行了深入的理論研究，在此基礎上研究了全齒廓嚙合斜齒齒輪泵流量特性，首次得到了完全消除斜齒齒輪泵流量脈動的螺旋角的選擇條件。
  7. And at last the measurement of helical gear pump flow pulse has been presented, which include how to measure the flow pulse and the validating the theory mentioned before and to try to the solve the problems happened during the process

    根據齒輪泵流量脈動的檢測要求，採用新的測試方法和手段，建立了中高壓齒輪泵性能測試裝置，並對樣機進行了性能測試。
  8. The researchful results indicate that the flux pulse ration of ordinary helical gear pump without clearance is less than that of the gear pump with clearence under the condition that the main parameters are same, and the flux pulse ration of ordinary helical gear pump is less than that of whole profile meshing helical gear pump

    研究結果表明：在主要參數相同的情況下，普通斜齒齒輪泵無側隙時流量脈動率小於有側隙時的流量脈動率；全齒廓嚙合斜齒輪泵比普通斜齒輪泵的流量脈動略小。
  9. At first, on the base of the analysis of the mechanism of the helical gear pump, the paper try to find the relationship of the helical gear pump flow pulse with its corresponding parameters, give the solution of the problems brought by the replace of spur gear to lay the firm basis for the structural design of helical gear pump

    本論文在對齒輪泵工作原理和流量脈動機理分析的基礎上，首先探討了斜齒齒輪泵的輸出流量脈動與斜齒輪各結構參數之間的關系，以及由於斜齒輪替代直齒輪帶來的相關問題並提出解決辦法，為斜齒齒輪泵的結構設計奠定基礎。
  10. Experimental study on the sliding - tooth pump

    擺動活齒泵流量脈動的試驗研究
  11. The flow characteristics of compound gear pump

    中心輪齒數對復合式外齒輪泵流量脈動的影響分析
  12. The tooth shape of gear pump has important influence on machining and characteristics of pumps, such as flow rate, fluctuation rate and noise etc. first, the working principle of tatsuno combined pumps is analyzed in this article

    齒輪泵的齒形對泵的加工、性能（如：流量、脈動率、噪聲）等有很大的影響。本文首先分析了進口tatsuno組合泵的工作原理，並進一步分析了其採用一對雙圓弧齒輪的優缺點。
  13. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  14. In chapter 3, the pressure pulse under the two situations of the system with and without damper is discussed at the basic of analyzing the flow rate pulse. then the conclusion that the system has filtering effect is drew after adding a damper in it, but its serious in power wastage because of adding a damper

    第三章，在分析液壓泵流量脈動的基礎上，討論並對比了系統加與不加阻尼兩種情況下各自的壓力脈動，得出系統中加一個阻尼后，具有一定的濾波作用，但是當流量較大時，由於阻尼的存在，系統功率損失比較嚴重。
  15. In this paper, on the basis of the analysis of gear pimp working principle, the mechanism of flow pulsation and methods of reducing flow pulsation are pulsation are studied. the computing formula of transient flow rate and the coefficient of flow pulsation are deduced. the relationship between the gear pump flow pulsation and the construction parameters of the gear is studied

    本文在齒輪泵工作原理和流量脈動產生機理的基礎上，首先從理論上推導了齒輪泵瞬時流量和流量脈動系數的數學模型，分析了齒輪泵的輸出流量脈動與泵齒輪各結構參數之間的關系，並對某型齒輪泵進行模擬分析研究，給出了齒輪泵的流量脈動分析結果。
  16. Among them the flow pulse is more standing - out, which is the main reason of its not more widely used. because high flow pulse will lead to the worse of the smooth movement of hydraulic motor and pipe, also cause pressure pulse which lead to a high noise, and give the destructive damage to the axial, bearing, valve, the connect of pipe etc. how to make the flow pulse low has become the research of scholars of many country

    其中流量脈動問題顯得尤其突出，它嚴重製約著齒輪泵的應用，因為泵的流量脈動大，不僅會使液壓缸運動的平穩性、液壓馬達回轉的均勻性性變差，而且會引起壓力脈動，進而使管道、閥門乃至整個系統振動（特別是在共振時） ，並發出很強的噪聲，這對軸、軸承、管接頭及密封都有破壞性影響。
  17. In addition, a calculating method of parametrically designing hydraulic motor with non - circular planetary gear is proposed aiming at maximal unit displacement and the minimal pulsation ratio by means of visual c + + 6. 0 software

    此外，探討了以單位體積排量最大為設計目標，流量脈動率最小為約束條件對非圓行星齒輪液壓馬達的參數化設計方法。
  18. Then a formula about flow of the gear pump and the coefficient of engagement overlap to find is obtained by area method. through analysis contact ratio and overlap ratio has the effect on the volume oil and the flow pulsating ratio

    然後採用面積法求得齒輪泵流量與齒輪嚙合重合系數的關系式，研究了齒輪嚙合重合系數對齒輪泵困油和流量脈動率的影響。
  19. Then, under the condition of satisfied the output volume request, a designing method of parametrically designing hydraulic motor with multi cylindrical gear is proposed aiming at minimal cubage with by means of visual c + + 6. 0 software, a calculating method of parametrically designing hydraulic motor with non - circular planetary gear is proposed aiming at maximal unit displacement and the minimal pulsation ratio by means of visual c + + 6. 0 software, and some designing method examples are provided for verifying the accuracy and possibility of those design methods

    再次，在滿足排量要求條件下，以體積小為設計目標，利用visualc + + 6 . 0軟體對圓柱多齒輪式液壓馬達進行了參數化設計軟體的開發;另外，以單位體積排量最大為設計目標，以流量脈動率最小為約束條件，利用visualc + + 6 . 0軟體對具有圓柱行星齒輪的非圓行星齒輪液壓馬達的參數化設計軟體進行了開發。
  20. Increasing original resistan coefficient of the secondary air duct can improve the adjusting performance of air damper, and inhibit pulsation of the flow rate

    增加二次風道的原始阻力系數，可以使風門的調節特性得到改善並抑制流量脈動。
分享友人
分享到 Line

分享到臉書