浸入深度 的英文怎麼說

中文拼音 [jìnrùshēndù]
浸入深度 英文
immersion depth
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 入 : Ⅰ動詞1 （進來或進去） enter 2 （參加） join; be admitted into; become a member of 3 （合乎） conf...
  • 深 : Ⅰ形容詞1 （從上到下或從外到里的距離大） deep 2 （深奧） difficult; profound 3 （深刻; 深入） thor...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 浸入 : immerse; dip; infusion
  • 深度 : 1. （深淺程度） degree of depth; depth 2. （觸及事物本質的程度） profundity; depth
  1. According to the feature that deformation resulted from water absorption and mildew appear mainly on the rabbet surface of ccf, this paper adopts rsst to spray a special waterproof sealant on rabbet surface of ccf, so that the sealant can get into fiberboard to certain extent by means of capillarity and penetration, blockage the holes between fibers and capillary, cut up passage of water and change the properties of soakage and sorption to water in capillarity and fiber. at the same time, solidified sealant can form a compact waterproof pellicle on rabbet surface so as to prevent water and humidity from fiber ' s expansion and mildewing

    針對吸水變形、霉變主要發生在地板企口表面的特徵，採用企口表面全封閉法，在復合強化地板企口表面噴塗特殊的防水封閉劑，使其依靠毛細管作用及滲透作用進入板內一定深度，堵塞木纖維之間的空隙及毛細孔通道，截斷水分傳遞的渠道，並改變毛細孔壁及纖維的表面性質以不利於水的浸潤與吸附，同時其固化后能在企口表面形成一層緻密的憎水薄膜，防止水分、濕氣從企口侵入板內引起木纖維膨脹變形、發霉等現象。
  2. The sensitivity algorithm is a knowledge of research on the affection of parameters varies to system performance. combination with pressing force and infuse time predicted model, by using sensitivity algorithm, the affection of cast temperature, mould temperature and infuse pressure on infuse time is researched deeply, and the affection of cast temperature, infuse time and infuse pressure on the pressing force in the origination stage of extrusion process. the sensitivity analysis has huge instructing significance to the selection of parameters

    靈敏度演算法是分析參數變化對系統性能影響的一種有效工具，所以本文引入靈敏度演算法，結合壓制力和浸滲時間預測模型，深入研究了澆注溫度、模具溫度和浸滲壓力對浸滲時間的影響關系，以及澆注溫度、模具溫度、浸滲時間和浸滲壓力對擠壓過程起始階段壓制力的影響，對于參數的選取，具有一定的指導意義。
  3. He dipped the stick into the water to fathom its depth

    他把棍條浸入水中，試探水的深度。
  4. Detailed predictions on the fluid flow in mold and in cavity of nozzle working end were obtained at different side - hole angle and submerged depth of nozzles, and then the flux variation of liquid steel passing through central hole of the three - hole nozzle and the fluctuation of liquid steel in mold were inspected based on above predictions

    針對3孔浸入式水口不同側孔傾角和浸入深度，數值模擬對結晶器內鋼水流動做出了較為詳細的預報，研究工作就此分別考察了水口中心孔流量變化和鋼水液面波動幅度。
  5. Designed immersion depth

    設計浸入深度
  6. The microstructures of precursor fibers, fibrous cloths, the composition of zirconia solution, the technological parameters of impregnation, and the modes of drying and firing were investigated

    對前軀體纖維、纖維布結構、鋯液配方、浸漬工藝參數、乾燥及燒成方式和制度進行了深入研究。
  7. Abstract : according to the character and actual condition of rh in shanghai baogang, molten steel flow in ladle and its effect on decarburization were studied with a three dimension turbulent flow and concentration modelling. the results show that, within a certain range, the decarburization rate increases not only with the increase of snorkel diameter and ar fluid flow but also with the decrease of the immersed depth of the snorkel

    文摘:根據上海寶鋼rh的特點和實際情況，建立了三維流場、濃度場程序，對鋼包內鋼水的流動、處理過程的脫碳進行了研究，並對它們的影響因素進行了分析.結果表明，在一定范圍內增加循環管直徑和吹氣流量、減小浸漬管浸入深度有助於提高脫碳速度
  8. Usable minimum immersion depth

    最小可用浸入深度
  9. The results show that the more deeper the nozzle immersion depth is, the less the molten steel velocity at the interface, the weaker the oscillation near the interface and the more difficult the occurrence of the slag entrapment become. compared with the round entry nozzle, the rectangular entry nozzle can reduce the occurrence of the slag entrapment

    結果表明:採用較大的水口浸入深度可以減小表面速度，抑制液面波動，避免鋼渣卷混的產生;與圓形水口相比，長方形水口能有效地減小卷渣發生的可能性。
分享友人
分享到 Line

分享到臉書