浸出后處理 的英文怎麼說
中文拼音 [jìnchūhòuchǔlǐ]
浸出后處理
英文
post leaching operation-
The results showed that : there were five stages in the rising process of the internal temperature of untreated, fire - retardant solution soaked, and fire - proof paint coated wood during the fire ; the carbonization rate of wood decreased by 21. 1 % ~ 35. 6 % and the rising speed of internal temperature also declined greatly when wood was soaked in fire - retardant solution or coated with fireproof paint ; the carbonization rate of white pine was 8. 5 % ~ 17. 4 % higher than that of the northeast china ash ; for untreated wood, the carbonization rate in tangential direction was 5. 8 % ~ 10. 5 % higher than that in radial direction ; the internal temperature of wood varies with the developing direction of combustion
結果表明：火災發生過程中未處理木材、阻燃浸漬處理和塗刷防火徐料木材內部溫度上升過程出現5個階段；經過阻燃浸漬處理和塗刷防火塗料后，木材的燃燒炭化速度降低了21 . 1 % ~ 35 . 6 % ，內部溫度上升速度大幅度下降；白皮松木材的燃燒炭化速度比水曲柳木材的燃燒炭化速度快8 . 5 % ~ 17 . 4 % ；未處理木材沿弦向的燃燒炭化速度比徑向快5 . 8 % ~ 10 . 5 % ；木材內部的溫度變化沿燃燒推進方向不同而不同。It shows with the increase of the amount of the mo in the si - mo infiltrant, the density of the infiltrated materials with the same performs increased, but the amount of the free carbon and pore also increased. it was the result of the capillary chocking - off caused by the separation of the mosj2 from the alloy infiltrant during the sintering process. after th thermal treatment at 2050, the amount of the free carbon and pore decreased. also. another cause for the unfully conversion of c into sic was the gas pressure. larger than the capillary force
實驗表明，對于同一坯體，隨著si - mo熔體中mo含量的增加，浸滲所得材料的密度隨之增加，但是，材料中的殘留c 、氣孔相的含量亦隨之增加。這是由於反應浸滲時，熔體中析出的mosi _ 2阻塞毛細管造成的。含殘留c 、氣孔相的材料進行高溫（ 2050 ）熱處理后，材料中殘留c 、氣孔相的含量大大減少。The data acquisition and data flow for various sensor carriers are analyzed systematically, and the calculation models are put forward. the model of quantification of wall - loss defects for in - line inspection with ultrasonic pigs has been established. and inspection data can be pretreated with this model, compressed with dpcm technique and treatd by dsp instruments
建立了檢測頭數據採集量及數據處理速率模型，首次建立了管道壁缺陷液浸超聲檢測的量化分析模型；提出採用該模型進行數據預處理后，採用差分脈碼調制技術進行數據壓縮，採用dsp器件提高數據處理速率。At the same time, it was indicated that the improved separating properties of membranes that had been marinated in methanol was pertinent to the degree of crystallization of polymer chains in membrane. also the effect of temperature and solvent mixtures on the performance of ca - eva composite membrane was related with reciprocity of polymer chains in membrane
同時，指出ca膜溶劑浸泡后處理效應與膜內大分子鏈的結晶程度相關，此外，還從膜內大分子鏈之間的相互作用解釋了ca eva復合膜中的溶劑效應和溫度效應。After dipped in amino trimethylene phosphonic acid ( atmp ) solution, anodic oxide films are annealed in pipe stove. the influences of concentration and temperature of atmp solution and annealing temperature on rising time, withstanding voltage and specific capacitance of anodic oxide films are studied. after hydration, anodic oxide films treated with atmp or not are analyzed by ft - ir
2 .將化成箔在氨基三甲叉膦酸（ atmp ）溶液中浸漬，取出烘乾后再進行熱處理，研究了atmp溶液濃度、浸漬溫度和熱處理溫度對氧化膜升壓時間、比容、耐電壓的影響，找到其最佳耐水合處理工藝;採用ft - ir對水合作用后的atmp處理氧化膜和未經耐水合處理氧化膜進行了分析。分享友人