浸漬速度 的英文怎麼說

中文拼音 [jìnzìsùdù]
浸漬速度 英文
impregnation speed
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 漬 : Ⅰ名詞1 （地面的積水） floodwater on low lying land 2 [方言] （積在物體上難以除去的油泥等） stain;...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. The results showed that : there were five stages in the rising process of the internal temperature of untreated, fire - retardant solution soaked, and fire - proof paint coated wood during the fire ; the carbonization rate of wood decreased by 21. 1 % ~ 35. 6 % and the rising speed of internal temperature also declined greatly when wood was soaked in fire - retardant solution or coated with fireproof paint ; the carbonization rate of white pine was 8. 5 % ~ 17. 4 % higher than that of the northeast china ash ; for untreated wood, the carbonization rate in tangential direction was 5. 8 % ~ 10. 5 % higher than that in radial direction ; the internal temperature of wood varies with the developing direction of combustion

    結果表明：火災發生過程中未處理木材、阻燃浸漬處理和塗刷防火徐料木材內部溫度上升過程出現5個階段；經過阻燃浸漬處理和塗刷防火塗料后，木材的燃燒炭化速度降低了21 . 1 % ~ 35 . 6 % ，內部溫度上升速度大幅度下降；白皮松木材的燃燒炭化速度比水曲柳木材的燃燒炭化速度快8 . 5 % ~ 17 . 4 % ；未處理木材沿弦向的燃燒炭化速度比徑向快5 . 8 % ~ 10 . 5 % ；木材內部的溫度變化沿燃燒推進方向不同而不同。
  2. Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition

    通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。
  3. The investigation presents a new method of dipping sic kiln furniture into 2 saturable solution or into the saturable solution of ca3 ( po4 ) 2 and a1po4 in order to beneficial to its crystalline structure change and its properties, to make it packed and decrease its porosity. it can also hinder the diffusion of oxygen so as to decrease the oxidation rate and lengthen the useful life. the mechanism of dipping two kinds of phosphate saturable solution were studied and proved by the results of scanning electron microscope

    本研究首次採用sic窯具材料浸漬ca _ 3 （ po _ 4 ） _ 2飽和溶液和浸漬ca _ 3 （ po _ 4 ） _ 2與alpo _ 4混合飽和溶液的方法，目的在於有利於窯具材料晶相結構的轉化和性能的優化；能堵塞材料的氣孔，降低透氣率，阻礙o _ 2擴散，降低氧化速度，延長窯具材料的使用壽命。
  4. Abstract : according to the character and actual condition of rh in shanghai baogang, molten steel flow in ladle and its effect on decarburization were studied with a three dimension turbulent flow and concentration modelling. the results show that, within a certain range, the decarburization rate increases not only with the increase of snorkel diameter and ar fluid flow but also with the decrease of the immersed depth of the snorkel

    文摘:根據上海寶鋼rh的特點和實際情況，建立了三維流場、濃度場程序，對鋼包內鋼水的流動、處理過程的脫碳進行了研究，並對它們的影響因素進行了分析.結果表明，在一定范圍內增加循環管直徑和吹氣流量、減小浸漬管浸入深度有助於提高脫碳速度
  5. The inorganic film is formed on stainless steel plate through dipping - draught method, and under the dropping rate 10cm / min

    以浸漬提拉法在不銹鋼基板表面施塗膜層，提拉速度10cm min 。
分享友人
分享到 Line

分享到臉書