浸透速度 的英文怎麼說
中文拼音 [jìntòusùdù]
浸透速度
英文
penetration velocity- 浸 : Ⅰ動詞1 (泡在液體里) soak; steep; immerse 2 (液體滲入) soak; saturate; steep Ⅱ副詞[書面語] (...
- 透 : Ⅰ動詞1 (滲透; 穿透) penetrate; pass [seep] through 2 (暗地裡告訴) tell secretly; let out; lea...
- 速 : Ⅰ形容詞(迅速; 快) fast; rapid; quick; speedy Ⅱ名詞1 (速度) speed; velocity 2 (姓氏) a surna...
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 浸透 : soak; saturate; steep; infuse; impregnate
- 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. (快慢的程度) speed; rate; pace; tempo
-
Abstract : combined with fundamental characteristics of in - situ leaching mining, this paper presents primary factors influencing the reation rates, such as lixivant concentration, oxidizer, porosity, permeability, seepage volocity, structure of ore, minerals of competition, etc. the factors which influence the reaction rates of in - situ leaching have been discussed
文摘:結合原地浸出工藝的特點,總結提出了影響原地浸出反應速率的主要因素,並就溶浸劑濃度、氧化劑、孔隙度、滲透系數、滲透速度,礦石的結構、構造及礦物的嵌布特徵,競爭礦物等對原地浸出反應的影響進行了分析與討論。The resin produced by the flame - retardant products with high strength and mechanical properties, thermal deformation temperature, curing speed, and good soak
該樹脂所生產製品具有很高的阻燃性能和機械強度,熱變形溫度高,固化速度快,浸透性好。Xt - p1007 unsaturated polyester resin is reactive flame retardant resin, heat distortion temperature, curing speed, good soak and toughness, both major requirements for flame - retardant and high mechanical strength requirements pultruded products
P1007不飽和聚酯樹脂是反應型阻燃樹脂,熱變形溫度高,固化速度快,優良的浸透性和韌性,主要應用於既要求阻燃又要求機械強度高的拉擠產品。Methods of dust character test - part 8 : determination of immersion - immersion speed methods
粉塵物性試驗方法第8部分:浸潤性的測定浸透速度法The investigation presents a new method of dipping sic kiln furniture into 2 saturable solution or into the saturable solution of ca3 ( po4 ) 2 and a1po4 in order to beneficial to its crystalline structure change and its properties, to make it packed and decrease its porosity. it can also hinder the diffusion of oxygen so as to decrease the oxidation rate and lengthen the useful life. the mechanism of dipping two kinds of phosphate saturable solution were studied and proved by the results of scanning electron microscope
本研究首次採用sic窯具材料浸漬ca _ 3 ( po _ 4 ) _ 2飽和溶液和浸漬ca _ 3 ( po _ 4 ) _ 2與alpo _ 4混合飽和溶液的方法,目的在於有利於窯具材料晶相結構的轉化和性能的優化;能堵塞材料的氣孔,降低透氣率,阻礙o _ 2擴散,降低氧化速度,延長窯具材料的使用壽命。The result of the experiment indicated that the capability of adsorption decrease with ultrasound intensity, while the rate of the extraction and adsorptin increase. the model resulst also showed that the theoretical value of the homogeneous model considering intrapartical diffusion and outside - surface diffusion with freundlich phase equilibrium equation are agfeeable with the experimental value
在吸附實驗中,測定了不同強度超聲場下梔子甙與1300樹脂上吸附平衡曲線、靜態吸附動力學曲線、動態穿透曲線。實驗結果表明,吸附容量隨著超聲波強度的增加而減少,而浸取、吸附速率隨著超聲波強度的增加而增大。分享友人