淬火方法 的英文怎麼說

中文拼音 [cuìhuǒfāngfǎ]
淬火方法 英文
quenching method
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 方法 : method; means; way; technique; process; procedure; plan; device; recipe; fashion; tool; maneuver
  1. In this paper, 6013al / sicp / gr metal matrix composite ( mmc ) was produced by spray codeposition, by means of changing the medium of quenching, influence of five types of heat treatment system ( furnace cooling, air cooling, water quenching, dry ice quenching, liquid nitrogen quenching ) and different aging temperature on the damping was studied systematically

    本文採用噴射共沉積方法制備了6013al sicp gr金屬基復合材料（ mmc ） ，通過改變淬火介質，較為系統地研究了五種熱處理制度（爐冷、空冷、水冷、乾冰冷及液氮冷）以及不同時效溫度（ 120 、 150 、 170 、 190及210 ）對6013al sicp grmmc阻尼性能影響。
  2. Test method for determination of cooling characteristics of quenchants by cooling curve analysis with agitation drayton unit

    通過攪拌冷卻曲線分析測定淬火劑冷卻特性的方法
  3. Steel - hardenability test by end quenching jominy test

    鋼的淬透性末端淬火試驗方法
  4. Abstract : the basic characteristics of hot _ isostatic press quenching method and its excellent performances on decreasing part deformation are described in this paper

    文摘:敘述了熱等靜壓淬火方法的基本特點以及在減小零件變形方面的優良性能。
  5. Test method for determination of cooling characteristics of quench oils by cooling curve analysis

    冷卻曲線分析法測定淬火油冷卻特性的方法
  6. Standard test method for determination of cooling characteristics of quench oils by cooling curve analysis

    通過冷卻曲線分析測定淬火油冷卻特性的標準試驗方法
  7. Methods of test for petroleum and its products - industrial quenching oils - determination of cooling characteristics - nickel - alloy probe test method

    石油和石油產品試驗方法.第414部分;工業淬火油.冷卻特性測定.鎳合金探頭試驗法
  8. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  9. Methods of measuring case depth for steel hardened by flame or induction hardening process

    鋼的火焰加熱淬火或感應加熱淬火硬化層深度的測量方法
  10. Standard test method for determination of thermal shock resistance for advanced ceramics by water quenching

    用水淬火法測定高級陶瓷製品耐熱沖擊性的標準試驗方法
  11. Advanced technical ceramics - methods of testing monolithic ceramics - thermomechanical properties - part 3 : determination of resistance to thermal shock by water quenching

    高級工業陶瓷.單片陶瓷的試驗方法.熱機械性能.第3部分:水淬火法測定耐熱沖擊性
  12. Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface

    文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。
  13. Heat treatment of ferrous materials - methods of heat treatment - part 5 : surface hardening

    鋼鐵材料熱處理.熱處理方法.第5部分:表面淬火
  14. Heat treatment of ferrous materials ; heat treatment methods ; hardening and tempering of tools

    鋼鐵材料熱處理.熱處理方法.第2部分:工具的淬火和回
  15. Strengthening mechanism of ion nitriding is different from surface quenching and cementation, which makes surface strengthen by quenching to get martensite. ionic nitriding is the way to make materials strengthe n, which result from the steady compound formed on the surface of the metal. there is no need for quenching after treatment

    離子滲氮的強化機理不同於表面淬火，滲碳等表面熱處理方法，這些方法必須進行淬火得到馬氏體使表面強化，而離子滲氮是在金屬表面形成穩定化合物而使材料強化，處理后不須淬火。
  16. Standard test method for non - destructive photoelastic measurement of edge and surface stresses in annealed, heat - strengthened, and fully tempered flat glass

    在退火淬火和全回火平面玻璃中邊緣和表面應力的無損光彈性測量的標準試驗方法
  17. According to structural characteristics of multi - phased alloy steels and the properties of ultrasonic propagation, microstructures characterization with different heat treatment processes ( normalizing, quenching / annealing, quenching plus low tempering, quenching plus high tempering ) for three steels ( 40cr, 38crmoal, gcrlssimn ) was studied experimentally by using ultrasonic methods. ultrasonic velocity, relative attenuation coefficient, and power spectral analyses were researched on the same samples respectively, on the basis of theory and experiment, the sensitivity and other characterizations of the three methods used to distinguish different microstructures were compared

    根據具有多種相結構合金鋼不同熱處理轉變產物的組織特點，以及超聲波在其中的傳播規律，利用超聲波速度、相對衰減系數以及功率譜分析三種方法，對三種鋼（ 40cr 、 38crmoal及gcr15simn ）不同熱處理（正火、淬火退火、淬火+低溫回火及淬火+高溫回火）轉變產物的顯微組織進行了超聲表徵研究。
  18. Abstract : compared with the normal technique the paper introduces many advantages of the laser quenching the ductile iron crankshaft

    文摘:介紹了激光淬火球鐵曲軸與常規的曲軸表面處理方法相比有許多優點，提出了一種激光淬火球鐵曲軸圓角部分掃描的新方法。
  19. I. investigation on laser surface hardening for metal materials in this work, the effect of the process parameters in laser surface hardening on the properties and surface feature of the hardened layer was studied

    一、金屬材料激光表面硬化技術研究。研究了激光表面淬火工藝參數和硬化層性能、強化效果之間的關系，對大面積激光淬火技術的基礎理論及搭接方法對組織性能的影響規律進行了探討。
  20. Fusion hardening - general description of method

    熔化淬火.方法的概要說明
分享友人
分享到 Line

分享到臉書