淬火處理 的英文怎麼說
中文拼音 [cuìhuǒchǔlǐ]
淬火處理
英文
hardening treatment-
There are many large - size air hammers, blast furnaces and costing equipment including all sorts of heat treatment equipment, costing equipment including all sorts of heat treatment equipments
我們有大型空氣錘多臺,有足夠的冶煉高爐鑄造設施有淬火退火回火各種熱處理設備。In our company we have forging, costing and heat treatment workshops with advanced producing equipments. all the tasks which refused by the other companies will be done well here. there are many large - size air hammers, blast furnaces and costing equipment including all sorts of heats treatment equipment, costing equipment including all sorts of heat treatment equipments
我公司下屬鍛造鑄造熱處理加工廠各一座,有先進的生產設備,可以接收其它部門不願承攬,甚至不敢承攬的艱巨任務,我們有大型的空氣錘和高爐冶煉鑄造設施和場地,有淬火退火回火各種熱處理設備。There are three main operations in the heat treatment of steel: hardening, tempering and annealing.
鋼的熱處理操作主要有三種,即:淬火,回火和退火。In this paper, 6013al / sicp / gr metal matrix composite ( mmc ) was produced by spray codeposition, by means of changing the medium of quenching, influence of five types of heat treatment system ( furnace cooling, air cooling, water quenching, dry ice quenching, liquid nitrogen quenching ) and different aging temperature on the damping was studied systematically
本文採用噴射共沉積方法制備了6013al sicp gr金屬基復合材料( mmc ) ,通過改變淬火介質,較為系統地研究了五種熱處理制度(爐冷、空冷、水冷、乾冰冷及液氮冷)以及不同時效溫度( 120 、 150 、 170 、 190及210 )對6013al sicp grmmc阻尼性能影響。Sagging and creep of the compo ? nents occur during heat treatment as a result of improper support of components or warped hearth in the hardening furnace
當對部件支持不當或在爐床翹曲的淬火爐中進行淬火時,部件在熱處理過程中會出現弧垂和蠕變現象。Medium frequency induction heating equipment are used in metal melting, temperature keeping, diathermic technology, metal - heat processing brass soldering, quenching, tempering and sintering
中頻感應加熱設備適用於各種金屬熔煉,保溫,透熱,金屬熱處理,釬焊,淬火回火,燒結,釬絲鋼絲等。Tapper pins, unhardened
未淬火處理的錐形銷Smooth tempered glass is manufactured by heating up float glass to swiftly and uniformly, with this special heat treatment and quenching process which increases glass strength up to four to five times vs, annealed glass, in case stresses beyond its capacity, smooth tempered glass simply disintegrates into innumerable small pieces, significantly reducing the risk of serious injury
鋼化玻璃是將浮法玻璃經過物理性淬火處理,使其表面形成均勻的壓應力,而內部則形成張應力,從而有效的提高了玻璃的抗彎和抗沖擊性能,強度達到了普通玻璃的3 - 4倍,當其破碎時則分裂成均勻純角不易傷人的小顆粒,使其成為一種現代生活中理想的安全玻璃。Abstract : in this paper, the surface of the ore milling roller was quenchedby the laser, so that increase its surface rigidity and improve its antiwear properties, and prolong its life
文摘:應用激光束對磨輥表面進行淬火處理,提高磨輥表面硬度,增強磨輥的抗磨損性能,從而達到延壽的目的。Process of carburizing and carbonitriding, quenching and tempering of iron and steel
鋼鐵的碳化氰化淬火和回火處理Induction hardening and tempering of iron and steel parts
鋼鐵件的感應淬火回火處理Process of induction hardening and tempering of iron and steel
鋼鐵的感應淬火和回火處理Frame hardening and tempering of iron and steel parts
鋼鐵件的火焰淬火回火處理The gear reducer for high strength steel carburizing, carburizing hardening, low noise transmission
減速器的輪為高強度滲碳鋼,經滲碳淬火處理,傳動噪音低。The principle of multi - method and multi - parameter is suggested, which should be followed during characterizing microstructures of alloy steels by ultrasonic not method. ultrasonic velocity ( c, ) of transformation products through different heat processes of three steels was measured by high - accuracy ultrasonic installation. the velocity of quenched microstructure of 38crmoal is the lowest, which gradually increases with increasing tempering temperature between 200 ? and 650 ? after quenching process
利用ti - 40n高精度超聲波測厚儀,研究了超聲波在不同鋼種、不同熱處理轉變產物中的超聲波速度c _ 1 : 38crmoal鋼淬火組織c _ 1最小,淬火后在200 650范圍內進行回火處理時,隨回火溫度的升高, c _ 1逐漸升高, hrc與c _ 1之間具有較好的相關性;正火組織的c _ 1介於淬火后中溫回火及高溫回火產物組織的c _ 1之間。Annealing could reduce hardness and raise toughness, which could be prone to mechanical machining. quenching and low temperature tempering could raise intensity and hardness of materials, not reduce toughness obviously. quenching on same temperature caused ticp / fe in situ composites having the best integral machine properties
退火處理使材料的硬度降低,韌性提高,便於機械加工;淬火+低溫回火處理使材料的強度和硬度提高,而韌性無明顯的降低;採用等溫淬火工藝,可使tic _ p fe復合材料具有最好的綜合機械性能。The milling head has adopted gear transmission
導軌經淬火處理,有良好的耐磨能力。Taper pins with internal thread, unhardened
未淬火處理的帶內螺紋錐形銷The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine
使用gleeble - 1500型熱模擬機,對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理,通過控制形變量、形變溫度和加載方式,調整鋼中馬氏體相變前的彈性應變能儲備,研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。Ansforging and tempering of steel
鋼的鍛造余熱淬火回火處理分享友人