淬硬層 的英文怎麼說
中文拼音 [cuìyìngcéng]
淬硬層
英文
quench-hardened case-
The result shows that the quenching inductor with wimble magnet inlaid is adaptable for this technique, and the vertical quenching machine can be used in mass production
結果表明，帶錐角鑲嵌導磁體的圈式感應器，其有效圈高度、錐角和內徑的合理匹配可以滿足淬硬層形態的要求，採用立式淬火機床連續淬火可以大批量生產合格的半軸。Methods of measuring case depth for steel hardened by flame or induction hardening process
鋼的火焰加熱淬火或感應加熱淬火硬化層深度的測量方法Abstract : this paper introduced the induction hardening experiment of components ? the gear - park and the drive support sprocket. give some advise on the pearlitic malleable iron ' s induction heat - treatment, and show coil design intending to meet the harden profilc according to the drawing
文摘:本文介紹變速箱零件? ?駐車齒輪和鏈輪支架的感應淬火試驗工作，提出對可鍛鑄鐵感應淬火中值得注意的問題及針對這兩種零件的特殊硬化層要求而設計的感應器。Effects of laser hardening technical parameters on hardened depth of t10 steel
10鋼淬硬層深的影響Abstract : this paper discussed the physicalmetallurgical process during laser hardening withsteel and cast iron, presented the technique designprinciple of laser hardening to achieve good resultsit also introduced the inspection method for laserhardened surface of steel and cast iron
文摘:討論了鋼和鑄鐵在激光表面淬硬時的物理冶金學過程，提出了激光淬硬獲得優良效果的工藝設計依據，介紹了對鋼鐵零件激光淬硬表層的檢驗方法。Meanwhile, the fracture was accelerated due to the uneven surface hardness and the unreasonable distribution of the hardening layer on the crankshaft, and the bad lubrication condition in service
同時軸左頸表面硬度不均勻、淬硬層分佈不甚合理，工作過程中潤滑條件差，加速了曲軸的斷裂。Moreover, it showed that the linearity rising relations were existed between the laser power and the thickness of hardening layer, and the linearity negative rising relations between the scanning velocity and peak rigidity
此外，結果還表明激光功率與淬硬層厚度成線性增長，而掃描速度與峰值硬度成線性負增長關系。Moreover, a method for iterating thermal and magnetic analysis is put forward. in chapter 5, the distributed characteristics of eddy and temperature fields in induction heating process are simulation by fem respectively, including the distributions of eddy and temperature fields during the whole induction heating process, the influence of frequency and magnetic disperse, and the prediction of hardened depth
第五章:用ansys軟體對感應加熱過程中工件內渦流場、溫度場的一些基本問題進行模擬及分析，主要包括:加熱過程中工件渦流功率密度及溫度分佈規律;頻率與磁力線逸散對加熱效果的影響;同時對感應淬火淬硬層深度進行了模擬預測。Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem
摘要考慮軋輥表面淬硬層與其心部金屬材料組織性能的差別，採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬，並將模擬結果與傳統強度校核方法進行了對比分析，研究了軋輥淬硬層厚度對輥間接觸應力的影響規律。Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface
文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。Determination of effective depth of hardening after induction or flame hardening of steel
鋼的感應淬火或火焰淬火後有效硬化層深度的測定Steels - determination and verification of the depth of carburized and hardened cases
鋼件滲碳淬火硬化層深度的測定和校核I. investigation on laser surface hardening for metal materials in this work, the effect of the process parameters in laser surface hardening on the properties and surface feature of the hardened layer was studied
一、金屬材料激光表面硬化技術研究。研究了激光表面淬火工藝參數和硬化層性能、強化效果之間的關系，對大面積激光淬火技術的基礎理論及搭接方法對組織性能的影響規律進行了探討。Ferrous metals, non - ferrous metals, ic thin sections, coatings, ply - metals ; glass, ceramics, agate, precious stones ; hardness testing such as that on the depth and the trapezium of the carbonized layers and quench hardened layers
黑色金屬、有色金屬、 ic薄片、層壓金屬、表面塗層；玻璃、陶瓷、瑪瑙、寶石等；炭化層和淬火硬化層的深度及梯度的硬度測試。Sintered ferrous materials, carburized or carbonitrided - determination and verification of case - hardening depth by a micro - hardness test
燒結鐵類材料.滲碳或碳氮共滲.用微型硬度測試法測定和驗證外層淬火的深度Study on abrasiveness of argon arc remelted quenching area of alloy cast iron camshaft
合金鑄鐵凸輪軸氬弧重熔淬火硬化層的磨損試驗研究Methods of measuring case depth
測量淬火硬化層深度的方法Aimed at willing of quenchhardening stell, by cutting experiment, the cutting performance of carbide vertical milling carbide cutter which is coated with different coating material is compared. the high speed process method which is adapted adapts to high hardness metal is explored
針對淬硬鋼的銑削加工，通過切削實驗，比較硬質合金立銑刀不同塗層材料的切削性能，探索適合高硬度金屬材料的高速加工方法。分享友人