深拉系數 的英文怎麼說

中文拼音 [shēnlāxìshǔ]
深拉系數 英文
cupping value
  • 深 : Ⅰ形容詞1 （從上到下或從外到里的距離大） deep 2 （深奧） difficult; profound 3 （深刻; 深入） thor...
  • 拉 : 拉構詞成分。
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained

    本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。
  2. Compared the results of fea and the data of experiment, we can analyse that the distributing of the seismic stress of polymer - geogrid reinforced material is similar to that of the static stress, but the stress values of them is different ; the seismic similar friction coefficient between the earth and reinforced material fall with the increasing of earthquake acceleration, model acceleration respond along the height of the model, etc. thirdly, according to the comparison and analysis of the model seismic fea results and model experiment data, we can find the polymer - geogrid reinforced earth seismic fea is reasonable, which is composed by earth element, contact element and reinforced material element

    通過對比有限元計算結果和試驗數據，分析得出塑料土工格柵筋材的最大動拉應力的分佈與靜拉應力的分佈沿筋材的埋深大致相同，只是應力的值大小不同；地震作用下土筋間的動似摩擦系數是隨地震加速度的增加而減小；模型沿墻高方向的加速度響應等。接著，根據模型動力有限元時程分析結果和模型試驗數據的比較分析，得出由土體單元、接觸單元和筋材單元組合的塑料土工格柵加筋土非線性動力有限元分析模式的合理性。
  3. Citing five - meter - high nanfei river rubber dam in hefei, one of the highest double - anchor water rubber dam in china as an example, while deeply analyzing some representative rubber dam projects in china, the article theoretically exploits the relationships among some technical parameters such as anti - pull intensity, internal pressure ratio, circum - oriented relative extending rate, etc. also has the author brought up his own opinion on rubber dam design & calculation theory, which is of high theoretical and applicative value for parameter optimization and combination of water rubber dam with a height of above 3. 5 meters. it also helps when building over - five - meter - high rubber dam using seamless rubber dam and rubber dam with steel wire as its frame. this article also exploits safety measures for designing & building rubber dam in navigation areas

    本文以充水式雙錨固橡膠壩目前國內最高（壩高5m ）之一的合肥市南淝河橡膠壩工程為例，並在對全國目前已建橡膠壩代表工程進行深入分析的基礎上，對壩袋的抗拉強度、內壓比、環向相對伸長率等技術參數之間的關系進行了理論探討和研究，並對橡膠壩設計計算理論提出了自己的見解和看法，對指導設計壩高3 . 5m以上的充水式橡膠壩技術參數的優化組合具有重要的理論和應用價值，特別對應用無搭接縫橡膠壩、鋼絲網骨架橡膠壩建造壩高大於5m的橡膠壩具有指導意義。
  4. Drawing piece unfold size is one basic condition under the calculation on coefficient, number of drawing, handbooks or books of press are not given, practice press production, die designer designs drawing die by experience calculation, after testing, according to deformation, state, defect shape of testing blank, shape and unfold size is revising, finally, unfold size and shape of blank are determined, designing period is longer, cost of die and work piece is to raise, economic benefit is to reduce

    拉深件展開尺寸是拉深可行性分析中計算拉深系數與拉深次數的前提條件，現有沖壓手冊或教材對于復雜拉深件的展開尺寸計算尚未論述。復雜拉深件的沖壓生產中，模具設計者憑經驗估計拉深可行性，設計製造拉深模進行反復試壓，根據試壓件的形變狀態，缺陷形貌，制定坯料展開尺寸和形狀，周期較長，因而生產成本高，經濟效益不佳。
  5. Neural network based prediction of frictional coefficient in metal forming deep drawing

    基於神經網路的板料拉深成形摩擦系數預測
  6. According to the documentation collected from domestic and abroad wang wei dong who works in huadong architect and structure institute utilizes the similar work property between the underground continuous wall and pile subjected the vertical loads, and introduces poulos method of elasticity and plastic which applies to pile foundation into the calculation for subsidence of underground continuous wall. pujialiu and yu yuzhou from water and electronic engineering of qinghua university, according to the result of three axes, define the concrete parameter utilize the model of non - linear e - b combined with the design cross section of dam in xiaolangdi, yellow river accept the total stress programme of thepd dam, and we analyze the stress and displacement of plastic concrete diaphragm wall by finite element method in comparison with the result of common concrete one. at same time, we consider the effect of the character of plastic concrete diaphragm wall which is composed of different gradients and adopting the level of stress and pulling stress infers whether the plastic concrete diaphragm wall is safe or not

    地下連續墻是一種歷史較短的施工方法，目前，砼防滲墻的設計還是以傳統的設計方法為主，根據查找國內外文獻資料，華東建築設計院王衛東利用地下連續墻與樁在豎向荷載作用下的工作性能有相似性，將適用於樁基的poulos彈性理論引入對地下連續墻的沉降計算中；清華大學水利水電工程系濮家騮、于玉貞根據三軸試驗結果確定混凝土的參數，利用非線性e - b模型，結合黃河小浪底土石壩設計剖面，採用thepd土石壩總應力程序，對深覆蓋層塑性混凝土防滲墻的應力、位移進行有限元分析，並與普通混凝土防滲墻計算結果加以對比，同時分析了不同配比塑性混凝土特性的影響，並採用應力水平和拉應力數值來判斷塑性混凝土防滲墻的安全程度。
  7. Based on energy theory, wrinkling criterion in deep drawing for axisymmetric parts is derived to take geometry parameters, friction coefficient, material properties, and the law of critical blank - holder force ( bhf ) of side wall wrinkling in the constraint condition of initial wrinkling into account

    從能量平衡原理出發，通過對屈服準則的線性化處理，推導了考慮幾何參數、摩擦系數和材料性能參數、板材皺曲時約束條件的軸對稱拉深成形過程中側壁起皺臨界壓邊力的變化規律，給出了皺曲判據。
  8. In this application, the lorentz force generated by the interaction between the current in the wire and the geomagnetic field produces an electro - dynamic drag leading to a fast orbital decay. in this paper, we make an intensive study of the process of de - orbiting using electro - dynamic tether system. the concrete work includes : firstly, i have studied the basic principle of how to generate the electro - dynamic drag, modeled via accuracy geomagnetism, made a concrete analysis of the de - orbiting duration, the magnitude and direction of electro - dynamic drag under the action of the dipole and accurate geomagnetic models, set up a counterbalance between electro - dynamic torque and gravity gradient torque, emulate the de - orbiting process of spacecraft, and compared the change of six orbital factors and the de - orbiting duration under the action of the dipole and accurate geomagnetic models

    本文對基於電動力纜繩的航天器離軌過程進行了深入研究，具體工作如下:首先，本文研究了電動力纜繩產生電動力拉力的基本原理，建立了精確地磁場模型;分別在偶極子模型和精確地磁場模型作用下，對電動力拉力的大小、方向、離軌時間及電動力纜繩傾角的大小進行了計算分析;建立了電動力力矩與纜繩系統重力梯度力矩的平衡關系;分析了電動力力矩為系統提供能量的原理;最後分別在偶極子地磁場模型和精確地磁場模型作用下，對受電動力纜繩作用的航天器的離軌過程進行模擬，分析了在不同精度地磁場模型下，航天器離軌過程中各軌道參數的變化情況，並比較了不同模型對離軌時間的影響。
  9. Base on review of existed study and application in suppressing cable vibration in the world, technique of mitigating cable vibration with viscous damper and mr damper has been investigated in this dissertation, and the main contents and progresses in form of summary are as following : 1 the motion differential equations of the cable - damper system are formatted, which take into account these factors, such as the inclined angle, sag, stiffness etc. coupling motion between cable and deck is studied with analytical and numerical method. numerical results show that large amplitude vibration of cable with beat rhythm will occur when exciting frequency of deck equals two times modal frequency of cable

    本文在對國內外斜拉索振動控制研究與應用現狀進行綜合評述、分析的基礎上，針對上述問題進行了深入研究，具體的研究內容和取得的成果包括： 1 、建立了斜拉索-阻尼器系統運動方程，對拉索與橋面的耦合振動作了分析和研究，數值結果顯示當橋面激振頻率等於某階拉索模態頻率的兩倍時，很小的初始擾動將引起拉索的大幅振動，並呈現拍振的特徵，與實測的拍振信號一致。
  10. This research project, based on the existing problems in mathematics curriculum evaluation and the conceptions of mathematics curriculum as the guideline, systematically analyzes the basic characteristics of the developmental evaluation, i. e. multi - dimensional, formative, developmental, understanding and inspiring. drawing on the modern mathematics conceptions, multi - intelligence theory and theories of constructivism, this project systemically illustrated the connotation of the developmental evaluation : the key of evaluation is for application ; the goal is multi - dimensional ; the process is context - dependent ; the outcome is to promote the development. in view of the conceptions of developmental evaluation ( i. e. human - centered whole evaluation ; quality - focused overall evaluation ; participation - stressed autonomous evaluation ; future - faced evaluation ; guiding evaluation and inspiring evaluation ), the components of the developmental evaluation model in the new mathematics curriculum is analyzed in details in this project ( i. e. goal system, subject system and object system ) and the core structure of the developmental evaluation is established ( i. e. evaluation indicator system model )

    本課題研究以數學課程評價的現存問題為著手點，以數學課程理念為目標指向，系統分析了數學新課程發展性評價的多元性、形成性、發展性、理解性、激勵性等基本特徵;以現代數學觀、多元智力理論、建構主義理論以及成功智力理論為理論背景，系統闡述了數學新課程發展性評價之意蘊?評價核心聚焦應用，評價目標指向多元，評價過程依存情境，評價結果歸依發展;以數學新課程發展性評價理念，即以人為本的全體性評價、注重素質的全面性評價、注重參與的自主性評價、促進完善的引導性評價、不斷進取的激勵性評價、面向未來的期望性評價為航標，深入剖析了數學新課程發展性評價模式的構成成分，即目標系統、主體系統和客體系統，由此構建發展性評價模式的核心圖式?評價指標體系的模式:以數學新課程發展性評價過程為參照，尋求並創設評價準則的設計技術，評價權重的構造技術，評價信息的收集技術，評價結果的分析與處理技術;以數學新課程評價系統內蘊的一般認識論、發生認識論與發展認識論指導評價方法，詳細探討了檔案袋法、表現性評價、自我評價與同伴評定相結合的方法、蘇格拉底式研討評定和測驗法在評價中的應用。
  11. This paper takes advantage of numeric simulation technology to investigate the weld - line movement and formability of twb with the same property and different thickness, analyzes the weld - line movement in three different drawing ways with the same drawing depth, and shows the normal rule of weld - line movement in different drawing ways, and the relationship between the weld - line movement and formability of twb of different thickness

    摘要本文利用數值模擬技術對相同材質差厚拼焊板的沖壓成形性和焊縫移動進行研究，分析了相同拉延深度、不同拉延方式下焊縫移動情況，揭示了不同拉延方式下焊縫移動的一般規律和焊縫移動量與差厚拼焊板成形性之間的關系。
  12. Based on the further study of dynamic characteristic of the tractor - implement combination, according to the integrated control model, which including the flowing three parameters : the engine load rate, drive wheel slip and work resistance, and the three control strategies, which are : highest production efficiency control strategy, oil consume economic control strategy and give attention to the above control strategy, we can adopt different control strategies according to different purpose of the task. applying the theory of the hybrid dynamic system to this case, the three control strategies can be abstracted to three discrete matters, and then the exchange model of the discrete matters of the top layer ( which called manage layer ) of the tractor - implement combination and the function decision model, which based on the nerve network, can be established. through this way, the best ad aptive controlling of the tractor came true

    本文研究了拖拉機機組的綜合控制問題及其最佳匹配方法，在深入研究機組動態特性的基礎上，根據發動機負荷率、驅動輪滑轉率和作業阻力三參數的綜合綜合控制模型以及三種綜合控制策略（最高生產效率的控制策略、燃油經濟性的控制策略和兼顧最高生產效率及燃油經濟性的控制策略） ，針對不同的作業目的，採用不同的控制策略，應用混雜動態系統理論，把三種控制策略抽象為三種離散事件，建立了拖拉機機組上層（管理層）離散事件切換模型，並建立了基於神經網路的功能決策層模型，從而實現了拖拉機機組的整機最優控制。
  13. Reconfiguration approach of distribution network based on both system reliability and feeder loss is presented in this paper. being an objective function both to maximize the reliability and to minimize the loss of network, constraint conditions are considered as operation limits. an optimal method of the minimizing both the average service unavailability index and feeder losses is described in this paper

    本文以配電網可靠性最高、網路損耗最低為目標函數，以配電網的運行滿足電力連續供應為約束，提出了基於排序選擇、對違反約束個體進行直接比較的改進自適應遺傳演算法，對配電網的可靠性按照深度優先搜索最小路進行計算，對系統的網路損耗按照牛頓? ?拉夫遜法進行計算。
  14. As for drawing process, it is a very important question to confirm limiting drawing rate [ m ]

    對于拉深工藝，極限拉深系數[ m ]的確定是一個很重要的問題。
  15. The limiting drawing rate is a very important index of blank ' s pressing capability, and it is the basic reference deciding to drawing pressing technology

    坯料的極限拉深系數是一種重要的沖壓性能指標，它是決定拉深工藝方法的基本依據。
  16. The author put forward a method of ann to calculate limiting drawing rate of cup part this time, it is a new thought for determining the cup ' s limiting drawing rate

    本次作者提出了採用人工神經網路的方法預測筒形件極限拉深系數，為確定筒形件極限拉深系數給出了一個新思路。
  17. A three - layer bp network structure is built up on the base of detailed analysis of influence factors of cup ' s limiting drawing rate in the article. use this ann model, better forecasting effect has been got, and the network has a higher precision, is satisfied with engineering design requirement

    本文在對筒形件極限拉深系數影響因素的詳盡分析基礎上建立了一個三層的bp神經網路，運用該網路模型得到了較好的預測效果，具有較高的精度，足以滿足工程設計計算要求。
  18. Cylindrical cup is a typical axial symmetrical part, though the deformation of material is simple in drawing process, but during the drawing process, exists a lot of influence factors ( including workpiece material character itself as well as each technological parameters ), and they restrict mutually between the factors. so how to calculate the limiting drawing rate of a cup becomes a complicated nonlinear and multi - gene question. to predicting limiting drawing rate of the cylindrical cup accurately indeed is a very complex subject

    筒形件是典型的軸對稱拉深件，在拉深過程中材料的變形雖然相對簡單，但是在生產過程中，由於影響因素很多（包括工件材料本身性能以及各個工藝參數） ，且各種因素之間相互制約，故如何準確地計算筒形件拉深極限就成為一個復雜的非線性多因子問題，要真正準確預測筒形件極限拉深系數也是一個非常復雜的課題。
  19. The principal work in this paper is to investigate the third - order nonlinear optical properties of three new organometallic complexes with z - scan technique, and study the molecule structural vibration of these complexes. in order to further understand their nonlinear optical characters there are six chapters in this paper, which can be divided into three sections : in the first section, i. e. chapter one, the current status of the development and practical applications of nonlinear optics are introduced briefly the third - order nonlinear optical effect is introduced particularly

    本文的工作主要是利用單光束z掃描技術研究了三種新型金屬有機化合物的三階非線性光學特性，並且利用拉曼光譜技術探索了這些化合物的結構振動信息，試圖從結構方面更深入的了解其非線性光學性質。論文共分六章，其主要內容概括為三個部分：第一部分，即論文的第一章，簡單介紹了非線性光學發展的現狀以及非線性光學的現實應用和意義，著重介紹三階非線性光學效應，用z掃描方法測量三階非線性光學系數的方法和理論。
分享友人
分享到 Line

分享到臉書