混流噴嘴 的英文怎麼說

中文拼音 [húnliúpēnzuǐ]
混流噴嘴 英文
mixing nozzle
  • 混 : 混形容詞1. （渾濁） muddy; turbid2. （糊塗; 不明事理） foolish; stupid
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  1. Using compressed air and transformer oil as working substance, this paper studied the pressure characteristic of internal - mixing nozzle and acquired the experimental relation on the pressure in the mixing chamber of internal - mixing nozzle against the operation parameters and structure parameters according to the method of step by step regression

    摘要以壓縮空氣和變壓器油為工質對內混式介質霧化油噴嘴的流量特性進行實驗研究，並通過逐步回歸分析的方法獲得了內混式介質霧化噴嘴油、氣流量系數與運行及結構參數的實驗關系式，可供設計使用部門參考。
  2. The cavitation flow in a nozzle at steady spray of a diesel engine was simulated, and the formation mechanism and distribution of cavitation inside the nozzle were analyzed using mixed multiphase flow model coupled with cavitation model

    摘要利用混合多相流體模型加空穴模型的方法，模擬了柴油機孔式噴油嘴穩定噴射時嘴內的空穴流動現象，分析了空穴在噴油嘴內形成機理及其分佈情況。
  3. Simulating results reveal that hydrodynamics of catalysts in riser reactor is very complex due to the effect of injection and catalysts backmix dramatically near the nozzle, reaction products unevenly distributie along the riser height, there exists apparently temperature gap between gas - phase and solid - phase near the nozzle and the temperture of two phase is nearly equal at middle - top part

    模擬結果表明，由於原料油射流的影響，提升管反應器內催化劑顆粒的流動特徵非常復雜，在噴嘴附近的催化劑顆粒存在明顯的滑落返混；裂化產物濃度沿提升管存在非均勻分佈；氣粒兩相間溫差在噴嘴附近顯著，在中上部氣粒兩相溫度幾乎相等。
  4. 1. instead of old inner - mixed vortex nozzles, improved y - type nozzle is developed. the designing calculation of new nozzle and corresponding air distributed organ are made, and the atomization effect is verified and compared with old one

    對原內混式旋流型噴油嘴進行改造，改用y型噴嘴，進行了噴嘴改造的設計計算和相應配風器的改造設計計算，比較和校核了其霧化效果。
  5. In this dissertation, the author summed up the muti - technique in fluid dynamics, heat and mass transferring, mechanical designing and computational technique and studied the conventional pressure spray dryers with different air disperse structure and outlet equipment, at last put forward the theme i. e. the study on combined spin - flow pressure spray drying technology, the main contents were as follows : ( 1 ) the combined spin - flow pressure nozzle was designed whose novel structure has no report at present, and the structural designing parameters were obtained through analyzing the physical characteristic of materials and distribution of particles

    本文總結了國內外在壓力噴霧乾燥裝置的研究應用狀況，並分析了現有噴霧乾燥裝置設計方面的優缺點，運用流體力學、空氣動力學、傳熱傳質學、機械設計和計算機技術等多學科知識，綜合研究了傳統壓力噴霧乾燥系統的單噴嘴霧化裝置在併流、逆流以及混流乾燥中的應用和噴霧乾燥塔的不同布風裝置以及出風裝置的設置情況等，提出了新型旋流式組合壓力噴霧乾燥技術並對此進行了研究，其主要內容包括： （ 1 ）本文創造性地設計出旋流式組合壓力噴嘴的基本結構，並通過對料液的物化特性研究分析以及顆粒度的分佈要求，給出了噴嘴的不同結構設計參數。
  6. The physical and chemical processes of nozzle atomization and the evaporation, mixing and combustion of propellant drop flow are very complex. for the reason, the researches on nozzle are still based on the experimental research now in or abroad

    由於噴嘴霧化及其噴霧流的蒸發、混和和燃燒是一個非常復雜的物理化學過程，目前國內外對噴嘴的研究仍以模型實驗研究為主。
  7. The research indicates that the orifice jet in mixing conditions has many different points from the pipe jet. focusing on the jet ejected from the orifices of different diameters and lengths, this paper studies the orifice jet when the fluid upstream of the orifices is in mixing conditions. the main purpose is to qualitatively study the effect of orifice diameters and lengths on the spread of the jet

    射流是在工程實際中廣泛存在的一種流動現象，噴嘴出口的流動狀態對射流的發展有很大的影響，前人對射流的研究主要集中於噴嘴前流體是完全發展管流的情形，本文研究了全混狀態下的板式射流，研究結果表明全混狀態下的板式射流具有很多不同於管射流的特點。
分享友人
分享到 Line

分享到臉書