渦流分離管 的英文怎麼說

中文拼音 [guōliúfēnlíguǎn]
渦流分離管 英文
vortex separation tube
  • 渦 : 渦名詞1. （漩渦） eddy; whirlpool; vortex 2. （酒窩） dimple
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  1. Vortex tube utilizes certain pressure gas as working medium producing the effect of separating, which makes the gas separating into cold and hot parts. the cold gas among them can be used refrigeration

    渦流管製冷是利用一定壓力氣體作為工質經過渦流管產生分離效應，使氣流分離成冷熱兩個部分，其中的冷氣流可用來製冷。
  2. In the second chapter, the fluid mechanics principle of vortex flowmeter at first was introduced. the classical theory about vortex flowmeter and the method of computational fluid dynamics about flow around body were expanded on, and the model of the single bluff body and the dual bluff body vortex flowmeter were constructed. and then, fvm - finite volume method - analysis software fluent was applied to analyze the flow phenomenon of flow over single bluff body or dual bluff body

    然後通過大量實驗和理論分析給出雙鈍體渦街流量計的設計準則：當管徑為d ，鈍體形狀為三角形，則鈍體設計參數為：銳邊寬度= 0 . 26d ，高度= 0 . 34d ，鈍體之間的距離= 1 . 2d （即當兩鈍體寬度相等且鈍體距離等於單鈍體兩列旋渦之間的距離） 。
  3. In the swirl, air stream at the periphery tend to have higher temperature compared to that in the center. by means of a separating plate, the airflow is separated into streams of hot and cold air. each stream of air then emerges from a particular end of the tube, named the cold and hot end accordingly

    氣體在熱端管的流動過程中，外層氣流溫度升高，內層返流溫度降低，高溫氣流從熱端閥流出，低溫氣體通過冷孔板流出，從而將進渦流管的氣流分離為冷熱兩股溫度不同的氣流。
  4. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  5. As a simple device without moving parts, vortex tube is composed of nozzle, vortex chamber, separating plate, control valve, hot - end and cold - end

    渦流管是一種結構極為簡單的製冷裝置，它由噴嘴、渦流室、分離孔板、熱閥以及冷熱兩端管組成。
  6. Effect of the rectify on the energy separation performance of the vortex tube

    整流器對渦流管能量分離性能影響的研究
  7. The performance of energy separation on the vortex tube designed by the author is studied at different cold mass flow ratios, and the characteristic curve has been drawn

    對于本文設計的渦流管，研究了不同冷氣流率時渦流管的能量分離特性，並且繪制了性能曲線。
  8. Vortex separation tube

    渦流分離管
  9. The inlet pressure is one of the important factors for influencing the performance of vortex tube. the separation of hot and cold is not very obvious at pj = 0. 20mpa

    25 k以及一直到060mpa過程中，隨著入口壓力的升高，渦流管能量分離非常顯著；比如，在n 44
分享友人
分享到 Line

分享到臉書