測壓計數據 的英文怎麼說

中文拼音 [cèyājìshǔjù]
測壓計數據 英文
piezometer data
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 壓 : 壓構詞成分。
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 據 : 據Ⅰ動詞1 （占據） occupy; seize 2 （憑借; 依靠） rely on; depend on Ⅱ介詞（按照; 依據） according...
  • 數據 : data; record; information
  1. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。
  2. Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading

    文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點
  3. This text studied the mutually interference influences to the aerodynamic force of irregular shape base on analysis using wind force and wind pressure data of super high buildings model obtained by wind tunnel tests, and provided reference to designer and expurgator on building code

    本文以超高層建築剛性模型的高頻天平測力風洞試驗數據和表面測壓風洞試驗數據為依據，研究了復雜外形建築的風力和高層建築相互干擾對風力影響，供設計者及規范修訂時參考。
  4. Pressure sensor and hygrothermograph sensor are adopted respectively to sense these change ; a plc and its analogue cell are adopted to collect and analysis the data ; a mcgs component software is used to process and store the data in real time

    給出了以壓力、流量和溫濕度傳感器為測量元件、以plc為主控制器、 plc模擬單元為數據轉換單元的詳細硬體設計、程序設計和組態軟體mcgs在上位機的運用。
  5. ( 2 ) the liman problem is normally adopted to check the liability of numerical method. the calculation error was within 9 % by comparison with the theoretic solutions of liman problem in the following case, the dimensionless calculation length was 2 with high pressure zone 0. 8, and the dimensionless state parameters were p1 = 2, p2 = 1, p1 = p2 = 1, u1 = u2 = 0. experiment results in literature [ 8 ] were used to check the adaptability of the numerical model developed here for unconfined gas cloud explosions and the calculation error was within 13 %

    （ 2 ）數值方法的可靠性通常用黎曼問題的解析解檢驗，本文以無量綱計算區長度為2 ，高壓區長度為0 . 8 ，狀態參數為p _ 1 = 2 ， p _ 2 = 1 ， _ 1 = _ 2 = 1 ， u _ 1 = u _ 2 = 0條件下的黎曼問題解析解對所編制的爆炸場計算程序進行了考核，結果表明該程序的計算誤差在9以內；為考核本文計算模型預測開敞空間氣雲爆炸的適用性，以文獻[ 8 ]的實驗數據進行了校核，計算誤差在13以內。
  6. This paper presents the pressure data collection system for a hydraulic supporting structure. this system can continuously measure the hydraulic support ' s pressure and forecast the future pressure

    摘要提出並設計出一種綜采液壓支架壓力數據採集系統。該系統實現了對液壓支架壓力的連續檢測，並通過計算機分析對未來的壓力變化趨勢作出預測，預防事故的發生。
  7. To set up reasonable designing and manufacturing techniques and accurate calibration system and to speed up forming the native pvdf pressure sensors is the direction of this project. first, based on the piezoelectric theorem, the theoretic support of pvdf pressure sensors is deduced. according to purposes of practical projects, special purpose sensor configurations are designed and the corresponding calibration system based on shpb ( split hopkinson pressure bar ) technique is built in succession

    本文從壓電材料的一般壓電控制方程開始，導出了pvdf壓電薄膜測壓技術的相關論據；根據測試目的以及被測結構的特點，設計了多種夾心式的傳感器構造形式；摸索出了一套基於國產pvdf壓電薄膜製作壓力計的加工、安裝工藝；建立了一套基於系統集成技術的多點pvdf壓力測試的數據採集、處理系統；建立了一套基於shpb技術、適用於實際工程應力范圍的pvdf壓力計的動態標定方法，並對兩種厚度的國產pvdf壓電薄膜進行了標定。
  8. This paper presents a new synthesized statistical method for acoustic detection data processing based on the contrast to and statistic & analysis on a great deal of data of acoustic detection, elastic modulus and tunnel operation conditions, which has been applied in many hydropower projects

    為此，通過對大量聲波、彈模數據和工程運行情況進行對比、統計和分析，總結出了一種針對隧洞高壓固結灌漿效果的多種聲波檢測綜合數據統計方法，並已用於多個水電項目中。
  9. The principle, method and procedure for adjusting loop flow distribution by measured network data ( pressure and flow of feature node ) in the hydraulic calculation of city gas network are introduced, and the cause of errors occurring when using this method is analyzed

    摘要介紹了城市燃氣管網水力計算中利用實測管網數據（特徵節點的壓力和流量）調整環流量分配的原理、方法和步驟，分析了該方法出現偏差的原因。
  10. Position summary : tests and inspects products at various stages of production process and compiles and evaluates statistical data to determine and maintain quality and reliability of products

    職位概述：負責各生產階段產品的測試和檢測；進行數據統計及評估以確保產品的質量與可靠性。鑒管和協調車間工人生產活動以及沖壓模具的修理。
  11. Because the harmonics in tangyin substation are primarily from electric traction loads, this paper gives the structures of several main locomotive models and general harmonics they produce. the harmonics produced by electric locomotive have a characteristic that their range and phase are both dispersive. this paper also analyzes the impedance - matching balance transformer ' s structure and harmonics injected into the power system at its primary side, and sums up the characteristics of the harmonics from electric traction loads in the tangyin traction substation

    鑒于湯陰變電站的諧波主要來自電力牽引負荷，本文列舉了電力機車幾種主要車型的結構以及它們產生諧波的概況，得出了電力機車的各次諧波電流幅值和相角具有較大分散性的特點。針對湯陰牽引變電站的牽引變壓器，分析了阻抗匹配平衡變壓器的結構及其高壓側注入電網的諧波，推導了有關計算公式。通過理論分析並結合湯牽線的實測諧波數據，歸納了電力牽引負荷注入湯陰變電站的諧波的特點。
  12. The monitoring system of remote electric quantity based on pstn obtains the electrical parameters of transformer by the data acquisition module, host computer dials every monitored station by roll polling. inferior processor transmits datas to the computer in superior monitoring center through pstn for storage and processing, to provide the analysis and statistics for the supervisor section. the system is simple and cheap, and it will have a good prospect of application in electrical system

    基於pstn的遠程電量監控系統通過數據採集模塊對變壓器的電參數進行採集，主機通過「輪循」的方式，依次撥通每一個監測站點，下位機將檢測到的數據通過pstn公用電話網送到上層監控中心的計算機系統進行存儲和處理，以提供主管部門的分析和統計之用。
  13. Because the microscopic model needs the distinct structure relation, the numerous input data and the long time of computing, the macroscopic model was used. after analyzing methods for the nodal pressure, the corresponding optimal program was drawn up

    由於微觀模型要求拓樸結構關系清楚，所需輸入數據多，計算耗時長，所以根據實際情況建立了管網的宏觀模型，針對宏觀模型的特點，分析了測壓點數目和位置的確定方法，進而編制了計算機優化程序。
  14. In this paper, the framework of measuring head of large diameter measurement system in multi - rolling - wheel method is designed by using the designing knowledge of precise mechanic, the knowledge of data processing and error correction and the method of the mathematical model fitting about measuring force and wheel deformation is described

    本論文中應用精密機械設計、數據處理與誤差修正等知識，介紹了大直徑多滾壓輪測量系統的測量頭結構設計和滾輪變形與測量力之間數學模型的擬合方法。
  15. The dynamic surface pressure was obtained according to experimental data

    根據所測非平衡張力，對應動態表面壓力數據也進行了計算。
  16. With the pressure measurement system for the swirl chamber diesel engine, by using the methods of equivalent power and the seven point three degree average for the indicator diagram, we can correct the tdc, smooth the pressure curve and make more accurate pressure data that is a well basis for the calculation of combustion heat release rate

    摘要本文在自行開發的渦流室柴油機壓力數據測錄系統的基礎上，利用等效功法和七點三次加權移動平均法，分別對示功圖進行了上止點校正和壓力曲線光順，使壓力數據更精確，為燃燒放熱率的計算打下了良好的基礎。
  17. The press instrument has many advantages, for example the measure range is 0 ~ 60mpa, the precision is one percent, and the hydraulic press of two roads was sampled every five minutes. this system makes use of the " data fusion " technique to compensate measuring errors caused by temperature changing. the press instrument has large storage space and can store about thirteen day ' s press data

    該測試儀的主要特點是：測量量程為0 60mpa ，精度為1 ；每5分鐘採集一次兩路通道液壓壓力值；採用「數據融合」技術進行溫度補償；數據容量大，能存放約13天的壓力數據； led顯示器可交替顯示兩路壓力值；無線數據通信功能，傳輸速率為9600kbps ；採用本安設計，可安全的應用於環境復雜的煤礦井下。
  18. Modern cylinder pressure acquisition system is deeply affected by the advanced computer hardware technology. a / d card with the capabilities of high resolution, high sampling rate, non discrepancy and setting sampling rate at will is combined with a lot of excellent measuring equipment such as crank shaft angle encoder, charge amplifier, industrial control computer, etc. we use four type 6117a46 spark plug cylinder pressure sensors made by kistler corp.,

    高速發展的計算機硬體技術深刻影響著現代氣缸壓力數據採集系統的發展，高解析度、高採集率、多通道、無相差和可以任意設定采樣頻率等特性的a / d板卡及一大批性能優越的相關測試儀器如轉角信號發生器、電荷放大器、工控計算機等。
  19. The portable infrared press instrument has the following characteristics : has small volume and weight and carry easily ; use a keyboard to input orders and display the corresponding information on the lcd display for the sake of the user ' s convenience ; has big data capacity and can collect 30 press measure instruments all the data which have stored for a week ; show the real - time date and time ; communicate through the infrared with speed of 2400kbps ; has the intrinsically safe circuit and can be safely used under coal mine

    本文所研製出的紅外線壓力手抄器的主要特點是：體積小、重量輕、易於攜帶；使用鍵盤輸入命令，並在液晶顯示屏上給予相應的提示，極大地方便了使用者；數據容量較大，可一次採集30臺壓力測試儀一周內存儲的壓力數據；全日歷實時時鐘顯示；紅外數據通訊功能，傳輸速率為2400kbps ；本安設計，可安全的應用於煤礦井下。
  20. It can collect, store and display press data. it also can transmit the press data to the host computer to deal with them. so it can completely replace the traditional mechanic hydraulic measure instrument

    它能夠進行壓力數據的採集、存儲、顯示，還可將數據傳輸給上位計算機進行數據處理，從而完全替代了傳統的機械式液壓測量儀表。
分享友人
分享到 Line

分享到臉書