測量極板 的英文怎麼說

中文拼音 [cèliángjíbǎn]
測量極板 英文
measuring pad
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  1. The approximation analysis result of band dipole model is obtained on the basis of the theory of mfl. the electromagnetic distribution feature of the defect in the steel panel is studied by means of simulation. the leakage magnetic distribution of the two defects and four defects plural and the defects in the column differently in the width are also assayed. conclusions that factors affecting flaw magnetic leakage to the panel also affect the column and magnetic leakage bx should be the feature of the flaw identification to several flaws are drawn

    在對漏磁檢測原理進行詳細介紹的基礎上，得出了帶偶極子模型的近似解析解，並以有限元數值模擬分析為主要手段，以鋼板上缺陷為對象，分析了各因素對缺陷漏磁場產生影響的不同規律，同時模擬分析了板上平行的兩條裂紋，四條裂紋以及柱體上寬度不同時的裂紋的漏磁場分佈特徵，得出結論:影響板上缺陷漏磁場的諸因素會對柱體上缺陷漏磁場產生同樣的影響;對于多條裂紋，宜用漏磁分量bx作為缺陷識別的特徵量。
  2. Mems ( micro electromechanical system ) has become one of the most rapidly development technologies. along with the rapid development of mems techniques, capacitive sensor is used widely whose capacitance changes small, which has put forward the new request to the measurement technique. the common measure for capacitance measurement is that convert capacitance to voltage, electric current or frequency. the area of polar plate of the capacitor becomes smaller and smaller, and the total capacitance of micro capacitive sensor is usually several pico farad only. as a result, its change amount is smaller

    Mems （ microelectromechanicalsystem ）近年來發展最快的技術之一，隨著mems技術的快速發展，電容式加速度計的電容變化變化量越來越小，對檢測技術提出了新的要求。在電容式傳感器中，常用電容檢測電路是將其轉換為電壓、電流或者頻率信號。目前的微型電容傳感器的極板面積變得越來越小，電容總量只有幾個pf ，變化量就更小。
  3. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  4. Using molecular imprinting method, the 1, 3 - dimethylxanthine theophylline, tho molecular recognition membranes, containing an segments as membrane formation sites and aa segments as functional sites, were prepared by the phase inversion technique. here, tho was selected as a template molecule. the hydrogen bonding between aa segments and the tho templates was measured by ft - ir and nmr. the tho templates can be removed from the membrane through washing with acetic acid aqueous solution. the permeation of tho through the membranes is far more than that of 1, 3, 7 - trimethylxanthine caffeine, caf, which demonstrated the function of tho molecular recognition of the membrane. the results also show that the increase of the tho templates concentration in the cast solution caused an increase of tho amounts taken into the copolymer membrane

    Ft - ir及nmr測試結果表明：制備的高分子膜中， tho模板分子和膜中的丙烯酸功能殘基存在著氫鍵鍵合作用。大量的極性醋酸水溶液可抽出膜中的模板分子。 tho溶液和與模板分子具有相似結構的1 ， 3 ， 7 -三甲基黃嘌呤咖啡因， caf溶液的基質透過實驗結果：進入膜結構中tho分子的量遠大於caf分子，這表明制備的高分子膜具有tho分子識別功能。
  5. They are applied to different situations and verified by experiments. analysis model of small ap oblique penetrating ceramic / metal light armor is established on the basis of energy model and the assumption of ellipse absorbing the same energy in back plate, giving the predictable formula about ballistic limit velocity. with energy model the optimization design in relation to ceramic / metal light armor is analyzed and the optimal coefficient of ceramic / metal composite armor is gained

    本文的主要研究內容如下： （一）建立了小型穿甲彈垂直侵徹陶瓷/金屬輕型裝甲的動量模型和能量模型，它們分別適用不同情況，並通過試驗驗證；基於能量模型和背板橢圓吸能相同假設，建立了小型穿甲彈斜侵徹陶瓷/金屬輕型裝甲的分析模型，給出了彈道極限速度預測公式；利用能量模型對陶瓷/金屬輕型裝甲的優化設計進行了分析，給出了陶瓷/金屬復合裝甲的最佳優化系數。
  6. Second, the test report produced by the system is not the standard case report. the purpose of this article is to develop a way to increase the clinical samples per test and design the mis for autodelfia 1235. [ methods ] ( l ) the remain volume in the reagent bottle corresponding of the assay buffer, incubation buffer, eu and ab was obtained by surveying the limited probe position of the right and left dispenser, respectively

    [方法]測定左右兩個試劑分配器的探測極限位置，獲得各類試劑的最低剩餘量；定量分析和測試配套藥盒各類試劑的實驗用量，獲得雙微孔板測試各類試劑的實驗配置量；定量檢測各類試劑瓶的容積，評估雙微孔板測試採用單微孔板封裝藥盒的可行性。
  7. This paper is consisted of two major parts : one deals with the general working performance of the fmghp by setting up mathematic model and developing computer procedure, getting the datum related to the capillary flow and heat transfer, analysing the working characteristics of fmghp in different working temperature, heat flux and inclination angle etc. in this part, the prediction of capillary and boiling limit are also included. the other major part studies the flow and heat transfer characteristics in the micro - film region formed by the meniscus attached on the metalic fin in the micro rectangular groove. investigations on the influence of width of groove and other factors on heat transfer in this region have been made. the importance of this micro - region in the heat transfer of the entire heat pipe has been unveiled. the heat transfer characteristics gotten by this research could be used in design and application and also optimization of this kind of fmghp

    本文在大量查閱現有國內外文獻的基礎上，總結並綜合前人有關微槽平板熱管理論研究方面的成果，對單面刻有槽道的微槽平板熱管進行了較為深入和細致的研究。本文的研究共分兩大部分，其中第一部分考察了該型熱管的整體工作表現，通過建立數學模型和開發相應的計算程序，得到了熱管內部毛細流動和傳熱的數據，分析了熱管在不同工作傾角、不同加熱熱流以及不同工作溫度等情況下工作特性的變化規律，考察了汽液界面上的剪切作用對熱管傳熱量的影響，並且進一步在理論上預測了該型熱管的毛細和沸騰極限。
  8. Sub - c mh - ni power batteries were prepared with excellent electrochemical performance based on the research of the high rate performance at different temperature. the change of temperature, impedance and weight loss was investigated in the process of recycle at high rate. it showed that the discharge time is 5. 9min at 10c and the middle voltage is 1. 05v

    三、根據對電池大電流和溫度性能的研究，研製了具有較好電化學性能的動力型鎳氫電池，並分別測試了電池在大電流循環過程中的溫度、內阻、重量和正負極板等的變化情況，以此分析引起電池性能衰減的原因。
  9. By a lot of trial and error, a new - type lightweight fireproofing board is developed. the test results indicate this production has obvious characteristics such as high temperature resistant, moistproofing, low distortion, and fireproofing limitation of 3h. its safety and toxicity has been examined according to relative national criterion and standard and the results show that no deleterious and poisonous gas is produced after combustion

    經過反復多次試驗、篩選，研製出的隧道防火板質輕，具有一定的柔韌性，便於施工;耐溫、耐潮濕;變形小;耐火極限達3h ;安全毒性方面，參照室內空氣質量檢測標準等規范進行了測試，測試結果為:產品不釋放有害氣體，屬環保型材料;按照國家相關的材料規范檢測其毒性，檢測結果表明，產品在燃燒后不產生有毒有害氣體。
  10. The paper made up a flexural experiment with six pieces of composite slab. during the every step of load exerted, the paper recorded the strain of cold - form steel deck and concrete, deflection, crack, slide, ultimate bearing capacity. by changing the thickness of cold - form deck, thickness and strength of concrete, amount of steel stud and other parameters, the paper discussed the behavior of loaded composite - slab

    本文進行6塊組合板的抗彎性能試驗，測試各級荷載下壓型鋼板及砼應變、組合板撓度、裂縫、板端滑移、組合板抗彎極限承載力；通過壓型鋼板厚度、砼板厚度、砼強度等級、栓釘數量等幾個參數的變化，探討組合板在荷載作用下的內力、變形情況。
  11. The article relates that the tool ' s measurement precision has been improved by applying cycling acquisition method, self calibration function and phase - sensitive detector. the image coverage rate is improved and reached to 60 percent by increasing the number of pad ' s buttons. the tool carried out two logging functions : fast - scanner mode and dip mode

    本文敘述了採用循環採集法、自刻度功能、相敏檢波等方法提高了儀器的測量精度；通過增加極板電扣的數量將圖像覆蓋率提高到60 ；實現了快掃描、傾角兩種測井模式；將測斜短節與預處理短節合二為一，縮短了儀器長度；去除了零伺服控制系統，簡化了電路；用fpga晶元對採集控制器重新設計。
  12. Through the technique to the blot - inject support in the soft rock of tucheng mine and the district of roof extremely falls in pieces to carry on experiment, carry on to measure and statistics for the relevant index to the underground pressure, combine the comprehensive analysis, it confirm the usefulness and the economy of the blot - inject support in soft rock entry

    摘要通過對錨注支護技術在土城礦軟巖及頂板極為破碎地帶進行試驗，對有關礦壓指標進行了測量統計，並綜合分析，證實了錨注支護在軟巖巷道中的有效性和經濟性。
  13. Abstract : theoretical distortion of the differential capacitor transducer with arch electrodes is analyzed in quantity while measuring the error motion of spindle

    文摘:定量地分析了圓弧極板型差動電容式傳感器在測量主軸回轉誤差運動時的原理誤差。
  14. To the object of two - flow, we trace its dynamic character and measure its correlated parameters by eight - electrode capacitance sensors. then turning the dispersed information to the integral information by sufficiently using information of object. the simulation experiment proved that this information fusion arithmetic can recognize the flow type precisely and timely

    針對管道中的兩相流被測對象，利用8極板電容傳感器對其在管道中的動態特性進行追蹤，並測取相關參量，利用信息融合演算法處理所獲得的信息，充分利用傳感器信息資源，將分散的傳感器信息融合成所測流型的整體信息。
  15. In order to design a reliable cathodic protection system for a ballast bank, it is necessary to develop a quantitative model for the shielding effect due to the inner structures on the protection current in a cathodic protection system of a ballast tank through a lot of numerical simulation or practical measure

    需要通過大量的數值模擬計算或實測，得到各種擋板對保護電流的屏蔽效應的定量化模型，以確立新的適合於壓載艙的陰極保護設計的技術體系。
  16. The project is completed in the collaboration of the transportation college of jilin university and transportation science institute in jilin province. the paper mainly studies the characteristics and mechanical performance of small size member of bridge, the problems of concrete dense degree and shear lag effect of wide flange. the static load test and supersonic nondestructive test of four pieces of prestressed i - girder with varying section are carried out in bridge structure laboratory of jilin university

    本文針對橋梁構件局部尺寸較小部位的混凝土密實度問題，進行了2片腹板寬度為14cm ， 2片腹板寬度為16cm的變截面預應力工字梁的靜載試驗和超聲無損檢測試驗，提出密實度系數的概念，對試驗梁的密實度進行定量評定，推導了工字梁的塑性系數公式，基於塑性理論給出了試驗梁的開裂荷載和極限承載能力計算公式，分析了試驗梁的密實度對其開裂荷載和極限承載能力的影響。
  17. Capacity variation of two capacitance of measuring membrance is also proportion to pressure. by amplified circuit the would be linearly converted to 420 ma dc two wire system current voltage or digital hart output signal high - speed addressable remote sender data road

    測量膜片的兩電容固定極板的被放大電路線性地轉換成420ma dc的二線制電流電壓或數字hart高速可尋址遠程發送器數據公路輸出信號。
  18. To meet the need of using photoelectric instrument to measure the photosensitive properties of the weak light of photodiode, because the current equipment is used in the daylight and the circuit is big and complicated, the instrument to measure properties of weak light of photodiode is developed, and the improved method is given

    摘要為了進行光電二極體的弱光光敏特性的測量和標定，改進現有測試儀只能適應日光環境且電路板體積大、線路連接復雜的缺欠，開發了一種光電二級管弱光光敏特性測量儀，並提出進一步改進的方法。
分享友人
分享到 Line

分享到臉書