溫和選擇壓力 的英文怎麼說

中文拼音 [wēnhéxuǎnzháiyālì]
溫和選擇壓力 英文
mild selection pressure
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 和 : 和動詞（在粉狀物中加液體攪拌或揉弄使有黏性） mix （powder） with water, etc. : 和點兒灰泥 prepare some plaster
  • 選 : Ⅰ動詞1. （挑選） select; choose; pick 2. （選舉） elect Ⅱ名詞（挑選出來編在一起的作品） selections; anthology
  • 擇 : 擇動詞（挑選） select; pick; choose
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 溫和 : 溫和lukewarm; warm
  • 選擇 : select; choose; opt; election; choice; culling; alternative
  1. Integrated the work on theory and experiment, the paper provides technical performance material at large about the automating and humidifying character of the centrifugal nozzle with firing pin type, high pressure and little aperture to the manufacture and user. with the valuable reference during the selecting the equipment and ascertaining the parameters, the users could select and control the humid parameter

    課題的理論與試驗兩方面工作相結合，為撞針型高壓小孔徑離心式噴嘴的霧化加濕性能提供了較為詳細的技術性能資料，為生產廠家和用戶在設備選型和參數選擇過程中，提供了有價值的參考，便於用戶正確而經濟地選擇、控制濕度參數，有效調節噴嘴孔徑、噴水初溫和噴水壓力的大小。
  2. Auxiliary pressure and temperature measurements make the multifrequency phase fluorometer an ideal choice for luminescence sensor design, testing and calibration

    輔助壓力和溫度測量讓多頻相位熒光計是發光探測傳感器設計、測試和校準的理想選擇。
  3. Through studying it is shown that in chagan sag, the geothermal gradients in the center are higher than those around the sag margin and major factors influencing the characteristics of temperature field distribution are the property of geotectogenesis and the differences in tectonic portion, lithology and underground water behaviour ; there are three types of mudstone compaction, i. e. normal compaction, undercompacition and overcomepaction ; there are two pressure systems in sandstone reservoirs, i. e. normal pressure and negative pressure systems and the strata ' s being uplifted and denuded is the key factor leading to the formation of the negative pressure system in reservoir ; and the distinctive temperature - pressure field characteristics in the sag are possessed of important petroleum geological significance in hydrocarbon source maturity, hydrocarbon generation, widening on oil and gas exploration domain and selecting exploration targets, etc

    研究表明，查干凹陷中心的地溫梯度高於凹陷邊緣，大地構造性質及所處構造部位、巖性與地下水活動的差異是影響凹陷地溫場分佈特徵的主要因素；泥巖壓實存在正常壓實、欠壓實和過壓實三種類型，砂巖儲層段壓力類型可分為正常和負壓兩個系統，地層抬升剝蝕是導致儲層負壓系統形成的主導因素；凹陷獨特的溫壓場特徵對烴源巖成熟、油氣生成、油氣勘探領域的擴大及勘探方向的選擇等具有重要的油氣地質意義。
  4. By analyzing and experimentally verifying the model, new ways of improving mixer performance were put forward. ( 1 ) heat water should be used in the mixer ' s temperature control to make the mixer work with optimal parameters. ( 2 ) the surface materials of the mixing chamber and rotors should be chosen rationally to change material surface energy and increase friction on them. ( 3 ) when the compound was processed under higher pressure of floating weight, shallow groovers or stripes parallel to the axle of the rotor should be made on the mixing chamber internal wall to increase the real contact area and improve mixing effect

    通過對模型的分析和實驗驗證，提出了提高密煉機混煉效果的新途徑： （ 1 ）密煉機溫度控制採用溫水冷卻，使密煉機處于最佳工作狀態； （ 2 ）通過合理選擇密煉室和轉子表面材料以改變材料表面能來增大膠料與它們之間的摩擦力； （ 3 ）在上頂栓壓力較大的條件下，在密煉室內壁與轉子軸線同方向加工淺的光滑槽可明顯改善混煉效果。
  5. Abstract : the processes of thermal - bonding and the features of raw material were breifly described, the temperature, pressure and speed to properties of thermal - bonded fabric were demonstratively related on the basis of three specific trials. futhermore, the authors present a point of view about the developing tendency of themal - bonding technologies for hygienic market after having an analysis upon current market status

    文摘:簡要介紹了熱軋非織造布工藝流程和衛生用熱軋非織造布原料的特點與選擇.通過對3個試驗的描述和對試驗結果的分析，詳細地論證了溫度、壓力和速度對熱軋非織造布性能的影響.根據市場的現狀，發表了對衛生用薄型非織造布生產技術發展方向的展望
  6. The paper analyzes the non - lineal relations of the quantity of heat exchange and water flux of coil exchanger in part - load operating condition, the shortage of deciding the water flux in bypass pipe, the disadvantage that the operating condition of pumps and chiller ca n ' t be met with the load change of the air conditioning system in different operating condition of using pressure - difference bypassing control in primary water pump system. using load control method in the change of the operating condition of primary water pump system can realize that the load change is small and reasonable in the on / off condition of pumps and m m chiller by comparing load control method in primary variable - flow water pump system with pressure - difference bypassing control method, back water temperature control method

    本論文從目前空調工程中使用的變流量水系統入手，研究了盤管換熱器在部分負荷下水流量與換熱量的非線性關系，分析了文獻中介紹的旁通管通流能力選擇的不足之處和一次泵水系統採用壓差旁通控制時，工況轉換不能滿足系統控制要求的缺陷；比較了一次泵變流量水系統中壓差旁通控製法、回水溫度控製法、負荷控製法的精確性，並得出了在一次泵水系統的工況轉換時，採用負荷控製法能使冷水機組及其相應水泵在啟停時的負荷變化范圍較小，更符合建築物的冷量需求，節能效果較好的結論。
  7. Using " shanghai no. 4 " and " dongcun jiaopei " as donor materials, variants with improved heat tolerance were obtained through treating haploid stem apexes with pingyangmycin and then culturing survived stem apexes with stress of higher temperature

    摘要用平陽黴素對青花菜「上海4號」和「東村交配」的單倍體莖尖進行誘變處理，以高溫作為選擇壓力，獲得一批耐熱性明顯比原始品種提高的單倍體變異體。
  8. Abstract : the forced state in key parts and their lifetime, the volume of high pressure chamber and ratio of pressure, the length of high pressure stroke and pressure stability, the relations between the deformation of high pressure chamber and temperature field and pressure field for three kinds of apparatus of making synthetic diamond under high pressure and high temperature were compared in this paper. the differences of these main apparatus were analyzed according to the degree of difficulty and ease in the technique, the choice of applicability and the cost and yield of them. it was emphasized that studying and developing the large sized belt - type press should be the way to make high quality saw diamond and change the state of making middle and low quality diamond in the diamond industry of our country, catching up with the international advanced level as well

    文摘:通過對高溫高壓合成金剛石3種主要裝備在關鍵部件受力狀況與使用壽命、高壓腔體積與壓力利用率、高壓沖程大小與壓力穩定性，高壓腔變形與溫場、壓場的關系等方面的比較，分析了3種主要裝備在技術難易程度、適用性選擇和投入產出比的差異；強調了我國金剛石行業要改變當前只能生產中低檔金剛石的現狀，向生產高品級鋸片級金剛石的方向發展，與國際接軌，應該走大型化兩面頂的道路。
  9. The forced state in key parts and their lifetime, the volume of high pressure chamber and ratio of pressure, the length of high pressure stroke and pressure stability, the relations between the deformation of high pressure chamber and temperature field and pressure field for three kinds of apparatus of making synthetic diamond under high pressure and high temperature were compared in this paper. the differences of these main apparatus were analyzed according to the degree of difficulty and ease in the technique, the choice of applicability and the cost and yield of them. it was emphasized that studying and developing the large sized belt - type press should be the way to make high quality saw diamond and change the state of making middle and low quality diamond in the diamond industry of our country, catching up with the international advanced level as well

    通過對高溫高壓合成金剛石3種主要裝備在關鍵部件受力狀況與使用壽命、高壓腔體積與壓力利用率、高壓沖程大小與壓力穩定性，高壓腔變形與溫場、壓場的關系等方面的比較，分析了3種主要裝備在技術難易程度、適用性選擇和投入產出比的差異；強調了我國金剛石行業要改變當前只能生產中低檔金剛石的現狀，向生產高品級鋸片級金剛石的方向發展，與國際接軌，應該走大型化兩面頂的道路。
  10. The method of optimization is the complex method. the objective function is the opration expenses of the hydrogen system. there were six decisive variables : the pressure and temperature of the high - pressure separator of vrds, gas ration to the prism unit from vrds unit and ssot unit, the pressure of the high - pressure separator of ssot and the entrance pressure of the cycle hydrogen compressor

    優化問題以氫氣系統的運行費用函數作為目標函數，選擇了6個決策變量，分別為： vrds高壓分離器壓力、溫度、 vrds和ssot裝置排入prism的氫氣量、 ssot高壓分離器壓力和循環氫壓縮機入口壓力。
  11. The prepared sdse modified zirconum meinbrane was tested at the wider range of tcmperaure and pressure and differellt composihons of hydrogen mixturc gases ( i. e. different hydrgen panal pressure ) in order to examine the performance of this membrane and the sole hpermselechvity of the membrane. the results showed tha the purity of the permeated hydrgen is l00 % at the base of the detection greatest lower lanit of the qhle mass spectrometer, and there was no impurity gas passed, the permeating flux and permeability of this membrane are from several decades times to one decade times more higher than tha of a palladum membran in the range of from 593k to 773k, puv = 0. 2 ~ 0. 3mpa, pdn = 4x l04pa - - 0. lmpa, the hydrogen permeatng flux is increased with the difference of the squto root of pressure, and presents a linear relationship, the pressure seems has no influence on the permeablity, the permeabi1ity is decreased with the increasing of the temperature, and presents an exponential relationship, accondng to the fitting curve of the relationship betwen the permeability and the temperatur derived from the experimenta daa, in the range of 593k ~ 773k, pup0. 2 ~ 0. 3mpa, pha = 4 x l0 # pa ~ 0

    在更寬的溫度范圍、壓差范圍內，在不同原料氣組成（即不同的氫氣分壓）條件下，對所制備的鋯表面改性膜進行了滲氫性能實驗，考核了膜對氫的唯一選擇滲透性，結果表明：在四極質譜的檢測下限內，只有氫氣存在，而無雜質氣體通過；在593k 773k溫度范圍內，鋯表面改性選擇滲氫膜具有高於鈀膜數十倍至十幾倍的滲氫流量和滲氫系數；其滲氫流量隨著膜兩側氫分壓平方根摘要差的增大而增大，並且呈線性關系；壓力對膜的滲氫系數幾乎無影響；膜的滲氫系數隨著溫度的升高而下降，井巨呈指數關系：根據對實驗數據所作滲氫系數與溫度關系曲線的擬合，在溫度593k 773k范圍內，壓差p 、 0二0
  12. Lmpa, the relationship is f di = l 55xl0 - " e47j l t ) in this range, the relative error of the hydrgen permeabilty bbeen the experimental values and the formula values are less than 3 %, the durability test showed that after the cycle experiments of prcssure and tempebe for 30 days, the perfrmance of the membran did not change, at last, the theory of hydrogen permeaton was discussed, too. through this work, the pfepared surf ases modified zirconium memran can satisfy the requirement of the purity and the permeating fiux of hydrogen isotope gas

    Imp范圍內，鋁表面改性選擇滲氫膜的數學表達式為： （ 1320 i 155x10 」 exd l 「 t ）在這個溫度和壓差范圍內，滲氫系數的實驗數據計算值與數學公式計算值的誤差在3以內；鉻表面改性選擇滲氫膜的壽命考核實驗表明，經過連續30大的循環溫度、壓力實驗，膜的質量、性能無變化；並討論了膜的滲氫理論。
  13. Abstract : emphasis is put on the recent development concerning the catalytic oxidation of methane to oxygenates by heterogeneous catalysis and liquid catalysis. for heterogeneous catalysis, the choice of catalysts, reaction temperature and pressure, oxygents, additives, reactors and reaction mechanism are summarized. different research systems of liquid phase oxidation of methane are reviewed

    文摘:本文對甲烷催化氧化制含氧化合物的研究，從多相催化和液相催化兩個方面進行了綜述；對多相催化的研究從催化劑的選擇、反應溫度、反應壓力、氧源、反應添加物、反應器及反應機理等方面進行了總結，液相氧化的研究則對不同的研究體系進行了詳細的綜述。
  14. Using the microwave selective heating property for materials, by setup equivalent equation, and first time inducing the electromagnetic field perturbation theory to the design of heating materials for substrate in mpcvd, three temperature distribution modes were established, including temperature distribution comprehensive mode of inhomogeneous plasma, temperature distribution composite mode of composite substrate materials, temperature distribution perturbation mode of composite materials, which ii provided an whole new technology route to the design of substrate heating system in mpcvd and guided the preparation of heating materials for substrate. and then the heating materials for substrate were designed and optimized to obtain large area homogeneous temperature distribution even larger than substrate holder ' s diameter. as an important part, this thesis researched the nucleation and growth of diamond films in mpcvd, systematically researched the effects of substrate pretreatment, methane concentration, deposition pressure and substrate temperature etc experimental technologic parameters on diamond films " quality on ( 100 ) single crystal silicon substrate in the process of mpcvd, characterized the films qualities in laser raman spectra ( raman ), x - ray diffraction ( xrd ), scanning electron microscopy ( sem ), infrared transmission spectra ( ir ), atomic force microscopy ( afm ), determined the optimum parameters for mpcvd high quality diamond in the mpcvd - 4 mode system

    該系統可通過沉積參數的精確控制，以控制沉積過程，減少金剛石膜生長過程中的缺陷，並採用光纖光譜儀檢測分析等離子體的可見光光譜以監測微波等離體化學氣相沉積過程；利用微波對材料的選擇加熱特性，通過構造等效方程，並首次將電磁場攝動理論引入到mpcvd的基片加熱材料的設計中，建立了非均勻等離子體溫度場綜合模型、復合介質基片材料的復合溫度場模型及復合介質材料溫度場攝動模型，為mpcvd的基片加熱系統設計提供了一條全新的技術路線以指導基片加熱材料的制備，並對基片加熱材料進行了設計和優選，以獲取大面積均勻的溫度場區，甚至獲得大於基片臺尺寸的均勻溫度區；作為研究重點之一，開展了微波等離體化學氣相沉積金剛石的成核與生長研究，系統地研究了在（ 100 ）單晶硅基片上mpcvd沉積金剛石膜的實驗過程中，基片預處理、甲烷濃度、沉積氣壓、基體溫度等不同實驗工藝參數對金剛石薄膜質量的影響，分別用raman光譜、 x射線衍射（ xrd ） 、掃描電鏡（ sem ） 、紅外透射光譜（ ir ） 、原子力顯微鏡（ afm ）對薄膜進行了表徵，確立了該系統上mpcvd金剛石膜的最佳的實驗工藝參數。
  15. Steel products for pressure purposes. derivation and verification of elevated temperature properties. an alternative procedure for deriving the elevated temperature yield or proof stress properties when data are limited

    壓力用鋼製品.溫升特性的導出和證明.第3部分:當數據給定時導出溫升屈服或試驗應力特性的選擇程序
  16. Under different load, when we apply this software to any time, region and cooling way, we can get the hottest spot increment and aging rating. to manufactory, the software means sounder thermal design, which will meet the load, putted forward by user, while to user, the software equal to a master who can help them decide the capacity rating of the transformer, which will fit the load. by using the software, the potential danger and the waste, caused by unfit load choice may be avoided

    研究開發了計算乾式電力變壓器負載能力的計算軟體，可對于各種絕緣結構，各種冷卻方式和任一地區、任一時間下運行的變壓器在不同運行載荷下的最熱點溫升絕緣老化率進行分析和計算，同時利用該軟體製造廠可以依據用戶提出的運行負載量給出相應的熱設計方案，用戶可根據運行負載情況利用軟體計算所需變壓器的額定容量，避免額定容量選擇不當造成隱患和浪費。
  17. According to the stress - strain condition at different parts, cfrc is laid selectively, not only the higher compression sensitivity can be attained, but also the interaction between compression sensibility and temperature sensibility of cfrc is divided

    根據構件各部位的應力應變狀況及cfrc的功能特性，有選擇地敷設cfrc ，採用直流探針壓降法測試，既獲得了極高的壓敏靈敏度，又實現了cfrc壓敏性和溫敏性兩種效應的解耦。
  18. Remarkably, the temperature must be limited between softening point and solidification value, at which the bond can get perfect fluidity and stickiness. effects of bond content and pressure on magnet product during heating - pressing process are the same with effects during common - pressing process. fourthly, it is more than 250 hours before magnet is eroded when it is coated with lacquer by way of cathode electrophoresis

    溫度對溫壓效果影響明顯，應當選擇在粘結劑軟化點以上、固化反應前的某一點，保證粘結劑具有適當的粘度和良好的流動性；與普通壓制工藝相同，溫壓工藝制備的粘結磁體密度和磁性能均隨壓制壓力的增大而提高，磁體性能和磁粉體積分數隨粘結劑含量變化的規律一致。
  19. A variety of gasket materials may be furnished for unusual temperatures, pressures, and corrosive conditions. for specific recommendations, consult us

    對于特殊的溫度、壓力和腐蝕性應用環境，可提供各種各樣的墊圈供用戶選擇。如果有特殊要求，請與我們聯系。
  20. The model can satisfactorily predict commercial operation results with regard to the edc conversion, vcm selectivity, pressure and temperature at the outlet of reactor coil

    與工業數據比較后發現，爐管出口的轉化率、選擇性、出口壓力和溫度等數據與模型預測值一致，表明模型具有較高的可信度。
分享友人
分享到 Line

分享到臉書