溫度測量誤差 的英文怎麼說

中文拼音 [wēndùcèliángwùchā]
溫度測量誤差 英文
thermometric error
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 溫度 : [物理學] temperature
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  • 誤差 : error
  1. The main computer is programmed under windows, while the assistant computer is programmed under dos. the last, based on the idea of module - structure, the software of the testing system are designed, thus this software system is compatible and transplantable to design again. the experiment of measuring principle is taken : take the xy flat of lathe as the parallel - pole device and adjust the angle of sensor, the rotating - probe can test the felloe mould in scanning way

    藉助虛擬儀器的思想，對測控系統進行了設計：採用光柵尺、光電編碼器測量可動部件的運動量，解析度高、誤差小；採用細分驅動的步進電機裝置，控制性能好；系統實施環境溫度的檢測、補償，提高了檢測精度；基於兩級微機組建測控系統：主機為人機界面，採用windows編程，從機用dos編程，實時性好；軟體設計採用兼容性和移植性好的模塊式結構，便於二次開發。
  2. This text divides into five chapters altogether : chapter one in the introduction, have introduced the common sensor of displacement, has pointed out the fine characteristic of hall ' s sensor, put forward the basic task ; chapter two have introduced the basic operation principle of hall ' s component ; chapter three introduce hall temperature performance, electromagnetic characteristic, zero error, frequency characteristic and these parameter commonly used compensation method and hall simple application of component ; chapter four having recommended the measurement principle of the feedback servo mechanism, systematic implementation method, the experimental result has appeared, structure the mathematics model, and has analysed the error ; chapter five have pointed out the developing direction in the future while looking forward to

    本文共分為五章：第一章緒論中，介紹了常見的位移傳感器，指出了霍爾傳感器的優良特性，提出了基本任務；第二章介紹了霍爾元件的基本工作原理；第三章介紹了霍爾元件的溫度性能、電磁特性、零位誤差、頻率特性以及這些參數常用的補償方法和霍爾元件的簡單應用；第四章介紹了反饋隨動機構的測量原理，系統的實現方法，給出了實驗結果，構建了數學模型，並對誤差進行了分析；第五章展望中指出了今後的發展方向。
  3. Based on developed experimental testing facility, the shading performances of southing horizontal shading devices, vertical shading devices and integrative shading devices of external windows are measured, the performance parameters including indoor temperature, air - conditioned cooling load and shading coefficient as so on. and the shading coefficient of experimental test results and calculation results based on design standard for building energy efficiency are compared, and the windows5. 2 simulation results are compared also. the measured results are consistent with the calculation results of horizontal shading devices and vertical shading devices

    本文利用研製的建築遮陽性能檢測裝置，對南向水平遮陽板、垂直遮陽板和綜合遮陽板外窗的遮陽性能（包括室內溫度、空調耗冷量和遮陽系數等）進行了實驗測試，並對遮陽系數的實驗測試結果與節能設計標準的計算值以及windows5 . 2軟體的模擬結果進行了比較分析，測試結果表明水平遮陽板和垂直遮陽板外窗的遮陽系數與計算結果比較一致，相對誤差分別為2 . 5 %和4 % ，而綜合遮陽板外窗的遮陽系數與計算結果的差值比較大，相對誤差達到10 %以上。
  4. 4. the thrust measurement device was calibrated, and the accuracy was 2 % fs. at the same time the signal of thrust measurement was input to the computer. e - type chromel - constantan thermocouple was used to measure the temperature of mpt, and the accuracy was 5 % fs. the vacuum measurement was realized by using zdf - 5427m vacuometer, and the accuracy was 3 % fs

    （ 4 ）對推力測量系統進行了標定並實現了計算機採集，推力測量系統最大相對誤差為2 fs ；溫度測量目前還只限於對mpt諧振腔壁溫的測量，使用e型鎳鉻?康銅熱電偶即可較容易實現，其測量精度為5 fs ；真空測量採用zdf - 5427m微機型復合真空計，其由熱偶計和熱陰極電離計復合而成，該真空計測量控制精度為3 fs 。
  5. This paper describes how to calculate the temperature of high - temp gas at the outlet of combustor by means of limited gas composition and analyses how errors in measuring gas composition, low calorific value of fuel, fuel composition and fuel temperature, etc. affect gas temperature

    摘要敘述了一種根據有限的燃氣成分推算燃燒室出口高溫燃氣溫度的計算方法，並分析了燃氣成分測量誤差、燃料低熱值、燃料成分及燃料溫度等對燃氣溫度的影響。
  6. Through the simulation and error comparison between classics regression model and neural network model, it showed that bp should be applied in liquid concentration measurement system to improve measurement accuracy and decrease the non - linear effect from temperature

    通過模擬研究，與傳統的回歸模型進行誤差對比，得出了應採用bp神經網路技術建立智能化液漿濃度測量模型，提高測量精度，克服溫度變化非線性影響的結論。
  7. In the paper, with system energy balance method and heat conductive equations ， on tne basis of short time heat transfer modeling established the long time modeling, considering heat interference in thermal well group. this paper used the finit element method for element division and computer analysis, and provided the operation temperature figure. acquired computation values agreed well with experimental results, the most difference between them was 5. 13 %

    本文採用系統能量平衡結合熱傳導方程，在淺埋套管式換熱器短期傳熱模型基礎上建立了長期傳熱模型，並考慮了管群熱干擾對模型的影響。並運用有限單元法軟體編程進行離散和計算機分析，得出模擬溫度場，其模擬值與實測的均值基本相符，兩者最大誤差小於5 . 13 % ，表明該模型具有一定的合理性和實用意義。
  8. For the existing transformer cooling control system has many shortcomings such as the complicated system control circuit, the low reliability, the protection methods of blower fan being so simple, large control error, high fault rate, massive maintenance work and no method to realize telecommunication, this thesis develops a novel intelligent power transformer air - cooled control system based on the center of microprocessor through all - round technology analysis and research

    本文針對變壓器冷卻系統使用常規控制系統存在的系統控制迴路復雜、可靠性低、風機的保護方式簡單而無法進行故障預測、主變壓器油溫測量精度低造成控制誤差大、故障率高、維護工作量大、無法實現遠程通訊等問題，經過多方面的技術分析和調研，設計開發了新型的以微處理器為核心的智能式電力變壓器風冷卻器控制系統。
  9. The influence arising from the anode voltage and gas pressure of gas - flow proportional counter and ambient temperature on the measuring error of the setup has been investigated by means of experiment

    實際測得了流氣正比計數管陽極高壓、工作氣壓和環境溫度對軟x射線熒光測量裝置測量誤差的影響。
  10. On the basis of analyzing the concept of charge temperature in the field environment, this paper discusses the unbalances of internal temperature of charge and environment temperature and the serious extents of traditional charge temperature measure error

    摘要該文在澄清野戰條件下的藥溫概念基礎上，介紹了野戰條件下裝藥環境溫度不均勻性、裝藥內部溫度不均勻性和傳統藥溫測量誤差嚴重性。
  11. A batch least - squares maximum likelihood estimator is employed to calibrate the model coefficients of accelerometer and a polynomial post - fit method is used to establish temperature models of these coefficients. the temperature models of accelerometer bias and scale factor of accelerometer are established between - 20oc and 50 oc. after compensating the temperature error by using these models, the post - fit residuals of the accelerometer output have been improved to 10 ? 5 g, and the trend term of accelerometer changing with temperature basically vanished

    採用最小二乘極大似然估計和多項式擬合的方法，分析加速度計靜態模型系數隨加速度計殼體溫度變化的規律，建立了- 20oc 50oc之間加速度計零偏和標度因數誤差的溫度模型，應用該模型對加速度計溫度干擾進行補償，補償后，加速度計輸出的擬合均方根誤差一到二個數量級，並且基本上消除了加速度計輸出隨溫度變化的趨勢項，使得加速度計測量精度得到了明顯提高。
  12. Results of experiments show that accuracy of temperature and acidity arrive at 0. 2 and 0. 02ph respectively

    實驗數據表明補償溫度的測量誤差小於0 . 2 ，酸度的測量誤差小於0 . 02ph 。
  13. The expression between the temperature of the objects that have real surface and the luminance of pixel in the image produced by ccd camera is deduced in this paper. the measurement errors are analyzed in this paper

    本文詳細推導了在高溫輻射體具有實物面的情況下，物體溫度和ccd圖像灰度之間的關系；討論了該方法的測量誤差及減少誤差的措施。
  14. In this paper, a kind of improved practical active linear bridge circuit with platinum resistor is used to eliminate the error mentioned above, and the precise temperature measurement can be made

    本文採用鉑電阻改進型實用有源線性化橋路克服了上述誤差，實現了高精度的溫度測量。
  15. The article launches discussing of temperature measuring precision, as well as analyses possible error of the measurement circuit and method of eliminating error. experimental data verifies this method

    文章重點圍繞溫度測量精度問題展開討論，分析了測量電路可能存在的誤差和消除的方法，最後以實際測得的數據進行驗證。
  16. Consideration of bp arithmetic of neural network has good character in function approach, we use it to ameliorate the colorimetric method to calculate the project temperature

    在綜合考慮了所有可能的誤差因素之後，提出了一種利用bp神經網路實現圖像色度信息向投影溫度映射的投影溫度測量方法。
  17. In temperature measurement of the thermal resistor, the nonlinearity of thermal resistor, lead resistor and unbalanced bridge may produce errors

    摘要熱電阻溫度測量中，熱電阻的非線性、不平衡電橋的非線性及引線電阻都會給測量帶來誤差。
  18. Then some measuring instrument now in use are introduced, including their applicability, measurement precision and cost efficiency, etc. in addition, two main factors influencing on torque measurement precision, shaft vibration and ambient temperature, are discussed and corresponding revolutions avoiding these influences are brought forward

    針對目前最為精確和行之有效的扭矩儀法，重點分析了被測軸的振動和環境溫度等因素所引起的測量誤差及其相應的解決辦法。
  19. Ambient temperature range in which the force transducer adheres to the error limits of the temperature - dependent technical specifications

    力傳感器保持溫度技術規范的測量誤差時周圍溫度的范圍。
  20. A kind of charge temperature measure equipment is developed whose measure precision ( standard error ) reaches 0. 6

    該文研發的藥溫實時測量裝置，其精度（標準誤差）達到了0 . 6 ，在國際同類產品中是先進的。
分享友人
分享到 Line

分享到臉書