溶體化熱處理 的英文怎麼說
中文拼音 [róngtǐhuàrèchǔlǐ]
溶體化熱處理
英文
solution heat treatment-
Besides, scan rate and cycle period also affect the result ; co - deposition of dualistic oxide is a focus of research, as an element in the same group, ir is selected. deposition rate of composition is decreased by the adding of ir composition, and when the proportion of ir exceeded 50 %, composition procession can be ceased. but cooperation of ir and ru oxide can highly increase the specific capacitance of active material ; annealing treatment under a certain temperature can help to change the hydrate ru composition into mixture state ru oxide, accordingly increase the stabilization of active material
研究表明:電解液的配製過程中，氯化釕濃度、溶液ph值、陳化時間、溶液溫度對電鍍效果均有影響，其中溶液ph值是最主要的影響因素;在儀器的使用條件探索中，理論結合實驗確定了本電鍍液體系循環伏安電勢窗的理想范圍，並發現循環伏安掃描速度和掃描周期對電鍍結果也有較大影響;混合氧化物的共沉澱是目前研究熱點，在此選用與釕同一族的銥作為共沉澱元素，銥的加入會阻礙氧化物的沉積速度，銥的比例超過50 %會使沉積作用停止，但是二元氧化物的協同作用使沉積的活性物質比容量大大提高;一定溫度下退火后處理作用會使水合釕化物轉變成混合價態的氧化釕，從而提高活性物質的穩定性。The sol - gel method and solid - state thermal reaction technique were used to prepare the composite oxides with variable lithium content. the doping treatments of some compounds were conducted. dta and tg were used to analyse synthesis mechanism, xrd to analyse phase composition, sem to observe morphology, li - b / licl - kcl / oxide simulated thermal cells to analyse the lithium - intercalation mechanism and properties of cathode material
實驗中採用溶膠?凝膠工藝和固相熱反應技術制取相應的不同鋰含量的復合氧化物，並嘗試對某些化合物進行適當的摻雜處理，應用dta和tg分析合成機制、 xrd分析所得物的物相組成、 sem觀察其形貌，模擬li - b / licl - kcl /氧化物的單體熱電池來分析陰極材料的嵌鋰機制及其電極性質。( 3 ) solid solution with good solid solution ability were acquired by solid soluting treatment for 25 min at 540 c, 560 c and 580 c, respectively, after that water quenching was carried on. in the case of 580 c, the coarseness of the precipitation at grain boundaries did not happen, equi - part 120 did not emerge at the intersection of three grains, these suggest that over sintering did not happen
6013合金實驗熱軋板材經固溶處理後於180時效4小時達到峰值硬度； （ 3 ） 540 、 560 、和580固溶處理25min 、水淬，得到了固溶充分的固溶體， 580的情況下晶界析出相未粗化、三晶粒交界處的角度未出現等分的120 ，表明未發生過燒。The foundry and heat treatment processes have been explored in order to improve properties of stainless steel. the method of solution heat treatment at high temperature with cooling controlled has been put forward
為了全面改善cr30mo鐵素體不銹鋼的性能，充分發揮不銹鋼的微合金化作用，對于不銹鋼的熱處理工藝進行探討，提出高溫固溶處理，控製冷卻措施。Larval fish of cynoglossus semilaevis g unther were treated with colchicines to get the karyotype, 12 ~ 50 - day larval fish were selected to be put into the solution of colchicine of different concentration for 5 - 6 hours. the fin, and the other part of the fish were cut off to be treated with low concentration infiltration, solidify, eduction and other procedures. at last, the suspending cells can be gained and treated with air - drying method
選取孵化時間為12 50天的幼魚，在不同濃度的秋水仙素溶液中處理5 6小時，分別剪取冠狀幼鰭、鰓絲和身體周圍的鰭條，通過低滲、固定、解離，得到細胞懸液，熱片法滴片， giemsa染色。Membrane distillation is an important branch of membrane separation technology which employees a hydrophobic microporous membrane for the separation process. during md process, feed contacts with one side of membrane, after water evaporates on hot side, vapor transfers to cold side under pressure drive, where vapor is condensed on cooling wall and then collected or removed
膜蒸餾技術是膜分離技術中的一個重要分支，它是指利用一疏水性的多孔膜，膜熱側與待處理液直接接觸，待處理溶液中的水在膜熱側汽化后，氣體在壓強差的推動下，通過膜孔傳遞到膜冷側，冷凝后收集或除去的一種分離技術。The bonelike apatite is formed on the anodized substrate when it is subjected to alkali and heat treatment and then dip into the sbf solution. after 7 days the bond strength of bonelike apatite layer to the substrates can reach 36mpa
當對氧化鈦膜進行適當的堿處理和熱處理，在人體仿生液sbf溶液中浸泡7天後表面形成的骨質磷灰石與基體的結合強度可達到36mpa 。分享友人