滑移擴展 的英文怎麼說
中文拼音 [gǔyíkuòzhǎn]
滑移擴展
英文
propagation of glide-
Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure
試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。Still, the change of vg parameter in the beam was investigated in this thesis. dilation of plastic belt in the beam is also studied. analysis show that there is clear direction during the dilation of plastic belt, which is similar with the path of shear - mode fracture
分析表明塑性區的擴展有明顯方向性，據此得到的塑性區擴展方向與剪切型斷裂時的斷裂路徑比較接近，也與加載過程中韌帶區出現的集中剪切滑移線的方向比較一致。Model of rockburest for extension of slip fracture in palisades
壁中滑移裂紋擴展的沖擊礦壓模型The flexural strength and fracture toughness of ti3sic2 material obtained by hot - pressing is 223mpa and 5. 1 mpa m1 / 2 respectively ; the mechanisms of grain bending, grain delamination, crack deflection inside the layered grain, crack deflection and branch, pull out grain are main energy absorbing mechanisms
~ 1ti _ 3sic _ 2材料的彎曲強度和斷裂韌性分別為223mpa和5 . 1mpa ? m ~ （ 1 / 2 ） 。主要能量吸收機制為：晶粒的彎曲、層間滑移，裂紋在層間擴展與偏轉，裂紋在晶粒間沿晶界擴展、分叉和晶粒的拔出。In the model, many processes or phenomena such as crack friction and growth, heat conduction, phase transformation of oxidant particulates, heat generation by viscous liquid layer, chemical reactions of gases in cracks, heat and mass exchange between phases of gas and solid, are described
模型描述了裂紋滑移擴展、熱傳導、含能顆粒相變、液化層粘性加熱、裂紋內氣相反應、氣相固相質量能量交換及與裂紋擴展耦合等過程。And then a laminar structure was formed in the front of the crack tip. a microcrack might nucleate at the crack tip and propagate ahead perpendicular to the laminar structure
首次發現純鎂裂尖變形以單系滑移為主，其斷裂過程是滑移減薄，形成層狀結構，然後裂紋垂直於層狀結構擴展。If the middle - below slope loses stability, the above slope will produce stress looseness and regulation, and bring slope deformation to top extending. it loses stability in tractive slippage model
在中下部滑體失穩后，上部滑體一定范圍內將產生應力鬆弛和調整，引起滑體變形向上擴展延伸，表現為牽引式滑移失穩模式。分享友人