滑觸軌 的英文怎麼說
中文拼音 [gǔchùguǐ]
滑觸軌
英文
contact fail-
Apply computer chip to control the circuit ; omron opto - elecrtonic control - ler and panasonic and mitsubishi inverter have stable performance, high precision, rapid reaction and long life - span ; the controlling plate applies tactile operation board which is handled easily ; vertical structural screen is easy to adjust the vertical printing pressure so as to ensure the quality of printing ; the frame lift is driven by electrical motor and installed with imported linear guide rails, of which the speed - adjust device, scraper and scraping blade can be adjusted within15 to 45 and can be set for many times so as to repeatedly printing with good precision and output, the flat bed is made of 2mm stain - less steel plates which are flat, smooth and indeformable ; it is also equiped with micromatic setting device in order to ensure the precision of multi - color overprint and auto air - intake device to ensure strong adsorption
採用電腦板控制電路,歐姆龍光電控制器,松下,三菱變頻器,行直穩定.精度高,反應快,壽命長,控制面板採用觸摸式操作面板,操作方便,六式結構型網版垂直升降印刷壓力可調保證印刷質量,機架升降採用電機驅動安裝進口直線導軌,刮刀、回墨刀可在15一45角調整,可設置多次,重復印刷保證產品精度.平臺板採用2毫米不銹鋼板製作,平整光滑不變形配有微調裝置,確保多色套印精度,配自動吸氣裝置,確保強有力的吸附。Abstract : three - dimension wheel - rail contact geometry is taken into account in studying the vibration between bridge and vehicle. the iteration method of wheel - rail creep force is proposed to improve the existed calculating method
文摘:對車橋耦合振動研究中輪軌關系的線性方法進行了改進,提出考慮三維非線性輪軌接觸幾何,採用迭代法求解法向力和蠕滑系數。Using vogel ' s wear index as the rail side wear index, the paper analyzes the side wear variations of rail head when the parameters in the wheel / rail system vary, analyzes the influences of track irregularity on rail uneven wear on gauge corner emphatically. this paper analyzes the rail side wear dates measured by track division of shan hai guan since 1990, then gains the relationship between side wear and traffic volume and sums up the characteristics and regularities in the formation and development of side wear. in the end, some measures for regarding the side wear on curves are put forward
從輪軌摩擦、輪軌接觸幾何關系、輪軌接觸應力和輪軌蠕滑等方面對鋼軌側面磨耗機理進行了探討,從軌道幾何參數、機車車輛運營條件等方面對鋼軌側面磨耗的影響因素進行了重點分析和總結;應用輪軌系統動力學,建立了輪軌空間耦合振動時變模型,採用vogel側磨指數作為鋼軌側磨指標,系統分析了輪軌參數變化的情況下,軌頭側面磨耗的變化規律,重點分析了軌道不平順對鋼軌不均勻側磨的影響;對山海關工務段1990年以後現場測得的曲線鋼軌側磨數據進行了分析,通過擬合得到了鋼軌側磨量與運量的關系曲線,並總結了曲線上股鋼軌側面磨耗的特徵和發生、發展規律;最後提出了一些減緩曲線鋼軌側面磨耗的措施。3 ) based on the analysis result of equal contact stress curve and the theory of elasto - hydrodynamic lubrication, the expression of the oil film thickness between roller ( or ball ) and orbit are calculated. the simulation result proved that the thickness of oil film is enough for bearing and lubricating
( 3 )基於等接觸應力曲線的求解結果和彈性流體動力潤滑理論,求得滾動體和軌道曲線間的油膜厚度表達式,並通過模擬分析論證了馬達正常工作時這種油膜能滿足承載能力和潤滑的需要。In this paper, wheel - rail rolling contact creepages and creeps of independently rotating wheel are analyzed, the effects of lateral and yaw motions of independently rotating wheel, and the curve radius to creepages of wheel - rail rolling contact are emphasisatically researched. 4
論文對獨立旋轉車輪的輪軌滾動接觸蠕滑率/力進行了分析,研究了輪對橫移和搖頭運動以及曲線半徑對獨立旋轉車輪輪軌蠕滑率的影響情況。New technique for keeping complete connection with heavy work - pieces sliding rail surface
保證重型工件滑動導軌面接觸質量的新工藝In order to realize smooth movement of mechanical system at a low velocity, the following work investigates new types of linear ultrasonic motors and antifriction technique by superposing the motor ’ s elliptical vibrating motion at the friction interface to change frictional characteristics, produce ultrasonic lubricant effect and realize active control of friction force
本文研究新型超聲波馬達,利用其產生於摩擦界面的橢圓軌跡超聲振動引起的潤滑效應和摩擦接觸行為的改變來減小摩擦力的大小,完成對摩擦力的主動控制,實現機械繫統的低速平滑運動。A new type of double - acting contactless sliding - vane pump was put forward to the defect analyzed on sliding - vane, which uses roller to control the locus of sliding vane to insure the minute gap between the stator and sliding vane
摘要通過分析滑片泵存在的缺陷,提出了一種利用滾柱控制滑片運動軌跡,使滑片與定子內表面保持微小間隙的新型雙作用無接觸滑片泵。Cranes - design calculation for rail wheels and associated trolley track supporting structure - general
起重機.軌道輪和相關觸輪滑軌支撐結構的設計計算.總則Cranes - design calculation for rail wheels and associated trolley track supporting structure - part 1 : general
起重機.軌道輪和相關觸輪滑軌支撐結構的設計計算.第1部分:總則分享友人