滯后補償 的英文怎麼說

中文拼音 [zhìhòubǔcháng]
滯后補償 英文
lag compensation
  • 滯 : Ⅰ動詞（使停滯; 使不流通） stagnate; block up Ⅱ形容詞（停滯; 不流通） sluggish; slow-moving; stagnant
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  1. That is why a delay, called lag compensation time ( lct ), is introduced between the real action and the display on the other side of the transmission pipeline

    這也是為什麼會有一個延遲，也被稱為滯后補償時間（ lct ） ，被引入到實際動作和在網路傳輸管道的另一端顯示之間。
  2. A measurable internal variable signal was feedbacked to compensate flow, so that the loading system tracked position system without delay

    通過對可測量的內部變量反饋，補償了活塞運動時流量的變化，使加載系統的跟蹤沒有滯后。
  3. The concept of acceleration delay compensation is put forward in this dissertation. by using acceleration delay compensation and tv tracker compensation technology the tracking capability of o - e theodolite tv tracking system is promoted to track fast moving targets at maximal 50 / s angular velocity and maximal 30 / s2 angular acceleration other than maximal 30 / s angular velocity and maximal 12 / s2 angular acceleration before while the maximal tracking error is still less than 3

    提出了加速度滯后補償的概念，並將其應用到提高電視跟蹤穩態精度中；結合電視跟蹤器補償技術，在保證最大跟蹤誤差不大於3的條件下，將目前的光電經緯儀電視跟蹤系統跟蹤最大角速度30 / s 、和最大角加速度12 / s2能力，提高到跟蹤最大角速度50 / s 、最大角加速度30 / s2 。
  4. The adaptive control with compensation for long time - delay system

    大純滯后系統的自適應補償控制
  5. Delay is obvious in large body because of its inertia, moment force, stress and gearing. transfer of electical cell increases the delay. this paper points out that the delay can be compensated by using the smith control algorithm. the result of computer emulation proved that a better quality is gained by using the algorithm on heavy nc machine

    大慣量物體，由於其慣性，加之傳動鏈長，所需的扭矩大，引起的應變大，加上電氣轉換元件的滯后，故滯後效應明顯.該文提出用史密斯控制演算法將滯后進行補償.計算機數字模擬結果說明，對大慣量有滯后的重型數控機床，應用該演算法能得到較好的控製品質
  6. Lag - lead compensation

    滯后超前補償
  7. Problems, which are the robust stabilization, the normal h control, the minimum sensitivity and mix sensitivity control, are discussed for the dead - time compensated upldt

    討論了時滯補償后系統的魯棒穩定化、標準h _控制、最小靈敏度和混合靈敏度控制等問題。
  8. So, the studies of administrative compensation theory of china shows hysteresis. legislation is disordered and can not become system

    所以，中國的行政補償理論研究滯后。立法凌亂而不成體系。
  9. Analysis of the effect of velocity delay compensation parameters on photo - electric servo systems

    速度滯后補償參數對光電伺服系統的影響分析
  10. A kind of nonlinear differential filter for the phase compensating, and the other filter basing on the phase and amplitude compensating are introduced in the paper. the filter designed is simulated by matlab and debugged in scm

    為此研究了非線性微分校正，能產生相位超前，用於補償濾波器的相位滯后且不增加高頻增益，后又提出基於相位與幅值補償的濾波器的設計。
  11. Methods for measuring and compensating time delay of active structural control system

    結構主動控制系統時間滯后測量與補償方法
  12. The low carbon steel, which has a high permeability, increases the magnetic field in the gap and the saturation current resulting in an increased damping force

    並且，提出採用內置彈簧蓄能器的方法，解決了由於蓄能器補償不足而造成的阻尼力滯后現象。
  13. Analyzing and modeling of the compensation error of measurement delay in active power filters

    有源電力濾波器檢測滯后補償誤差的分析與建模
  14. In order to decrease the over - adjusting in temperature and transaction time, a multi - model selector was provided to different scenarios of ascending temperature to make this system be simulated under simulink ' s circumstances. the result of simulation demonstrated that the effect of the system temperature control with model selector is superior to that of the system with pid controller or with pure lag compensation

    為了進一步降低滲氮爐到溫前的溫度超調量及過渡時間，又提出用一個模式控制器來進行多種升溫方式的選擇並在simulink環境中對帶有模式控制器的溫控系統進行了模擬實現，模擬結果表明帶模式控制器的滲氮爐溫控系統的控溫效果又要優于帶純滯后補償的pid控制系統。
  15. According to the demand of the technology of gas nitriding, the author firstly put forward total demand analysis and systematic model - making for gas - nitriding furnace ' s temperature control system with uml in order to definite the temperature control system ' s functional requirement and the interaction of each object in this system on the basis of this idea. it ' s thought that the key step for realizing the temperature control system is the analysis and the design of the pid controller. considering that the gas - nitriding furnace has significant temperature lag, the author initially pointed out the opinion of realizing the system of temperature control by pid controller with pure lag compensation and then designed the parameter of pid controller with pure lag compensation and ordinary pid controller by matlab6. 5

    這篇論文以作者本人在原工作單位的技術改造實踐中（即滲氮爐的技術改造）所遺留下來的技術問題為背景，根據氣體滲氮工藝的具體需要，首先提出了用uml對滲氮爐溫控系統進行總體的需求分析和系統實物建模以明確溫控系統的功能需求及各對象間的交互，在此基礎上分析得出溫控系統實現的關鍵所在即pid控制器的分析設計和實現，由氣體滲氮爐存在較大的溫度滯后這一特性，初步提出用帶純滯后補償的pid控制器來實現溫控系統的溫度控制，隨后藉助于matlab6 . 5平臺對帶純滯后補償的pid控制器和常規的pid控制器進行參數的設計與整定，進而在matlab6 . 5的simulink模擬環境中對基於兩種不同pid控制器的滲氮爐的兩種溫控系統的設計方案進行了模擬實現及模擬結果比較，結果表明，採用帶純滯后補償的pid控制系統的魯棒性較常規的pid控制系統好。
  16. Based on the characteristic of the coupling objects it optimizes the decouple parameters, and the simulation result proves that the decoupling optimized algorithm compensates the hydraulic system lag, achieves the best collection efficiency, and enhances the stability of walking

    並根據耦合對象的特性，進行去耦優化，模擬結果表明該去搞優化演算法能補償液壓系統滯后特性，獨立進行集擴頭高度最優調節，達到最佳集礦效率，提高行走穩定性。
  17. This paper deeply discusses the cascade control system and the smith - predictor system of the conventional control system, states a combination system between them in order to improve the weaken control quality of the cascade system which involve a negligible large time - delay in its inner loop

    本文對常規控制理論中的串級控制和smith預估補償控制兩種控制方案進行了討論，引出了利用smith預估補償控制特點來解決串級控制系統的副迴路中存在大純滯后環節時，系統控製品質差的問題。
分享友人
分享到 Line

分享到臉書