滯彈性應變 的英文怎麼說

中文拼音 [zhìdànxìngyīngbiàn]
滯彈性應變 英文
anelastic strain
  • : Ⅰ動詞(使停滯; 使不流通) stagnate; block up Ⅱ形容詞(停滯; 不流通) sluggish; slow-moving; stagnant
  • : 彈名詞1. (彈子; 小球形的東西) ball; pellet 2. (內裝爆炸物, 具有破壞和殺傷能力的東西) bullet; bomb
  • : Ⅰ名詞1 (性格) nature; character; disposition 2 (性能; 性質) property; quality 3 (性別) sex ...
  • : 應動詞1 (回答) answer; respond to; echo 2 (滿足要求) comply with; grant 3 (順應; 適應) suit...
  1. Anelasticity is normally not measured or defined in terms of stress or strain.

    一般不用力或來度量或定義。
  2. Here a kinetic study has been made in order to determine the relationship between the relaxation of elastic energy and the hysteresis expansion by pre - deformation of shape memory alloys

    本文根據馬氏體相熱力學和動力學,並結合相關的實驗結果,研究了能弛豫和相后的關系。
  3. Secondly, by low - cycle and reverse horizontal loading test, their properties including strength property, deformation property and energy property are studied. we study the loading characteristic values ; the property of hysteretic curve and skeleton - frame curves ; the ductility property and stiffness degradation. at last we analyze the destroy principle and affection reasons of hollow shear wall of r. c with vertical seams in different height and loading measures, we also give the bearing capability calculation formulas and design advises for new type hollow shear wall of r. c

    首先運用ansys有限元程序分析階段水平外荷載施加后,帶豎縫鋼筋砼空心剪力墻板內力分佈及形情況,再在試驗數據的基礎上,研究低周反復水平加載條件下,各試件的強度、形、能量特;各試件的荷載特徵值;各試件的回曲線、骨架曲線;延及剛度退化等參數;最後,分析了不同剪跨比和加載條件的帶豎縫鋼筋砼空心剪力墻板的破壞機理和承載力影響因素,並給出不同剪跨比和加載條件的帶豎縫鋼筋砼空心剪力墻板承載力計算公式及設計建議。
  4. Based on the theory of thin - walled curved bar, reasonable hypothesized a third - ord parabolic curve, the paper adoptes variational method on energy, taking the coupled relationship of the effect of curvature radius, bend, torsion and shear - lag into consideration, establishes the elastic governing differential equation and boundary conditions for thin - walled curved box girders, which set the foundation of theoretical analysis of shear - lag effect in thin - walled curved box girders

    摘要文章以薄壁曲桿理論為基礎,合理地假設了三個剪力翹曲位移函數,用能量分法推導出考慮曲率半徑影響、彎、扭、剪力耦合的曲線箱梁控制微分方程及其邊界條件,為薄壁大麴率箱梁剪建立了理論分析基礎。
  5. The main research works and conclusions of this thesis are listed as follows. the dynamic analysis model of elastic mechanism system with damping alloy parts is deduced based on the relationship between stress and strain of the material, also the analysis model under viscous damping model, complex damping model, nonlinear damping model and viscous - elastic damping model is put forward using the finite element method

    本文的主要研究工作及結論如下:從材料本構關系出發,導出了阻尼模型、復阻尼模型、非線阻尼模型、粘阻尼模型下的有限單元分析模型,進而給出了含阻尼合金構件連桿機構系統動力學模型。
分享友人