滴料速度 的英文怎麼說

中文拼音 [dīliàosùdù]
滴料速度 英文
gob speed
  • 滴 : Ⅰ動詞（液體一點一點地向下落） drip Ⅱ名詞（一點一點地向下落的液體） drop; droplet Ⅲ量詞（用於滴下的液體的數量） drop
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. Studies showed that process and condition control had critical effect on the preparation of yig phase, and the proper conditions specialized as follows : using ammonia - ammonium nitrate ( nh3 - nh4no3 ) as precipitant, ph scope from 10 to 10. 5, using dissolving salt as law materials, dropping their mixed solution into precipitant, precipitation rate at 0. 8ml / min

    研究表明，共沉澱的過程和條件控制對yig的合成具有重要影響。實驗得出共沉澱的合適條件為：以nh _ 3 - nh _ 4no _ 3為緩沖溶液，控制ph范圍為10 . 0 ? 10 . 5 ，採用可溶性鹽為原料配製溶液，滴加到沉澱劑中的共沉澱方式，共沉澱速度為0 . 8ml min左右。
  2. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  3. As well - known, there is an induced current on the surface when metal material is in the high frequency electromagnetic field, since tending to skin heating effect to make the temperature of metal material surface go up promptly, surface beginning melt when temperature reaches the melting point of metal, metal material is heated up continuously by surface to core till the metal droplet of melting

    自懸浮定向流技術制備金屬納米微粒與一般的蒸發冷凝法有所不同，其原理是：金屬材料在高頻電磁場中產生表面感生電流，由於趨膚加熱效應使得金屬材料表面的溫度迅速升高，當溫度達到金屬的熔點時表面開始熔化，通過熱傳導作用金屬材料由表面到芯部不斷加熱直至熔化成金屬液滴。
  4. Middle speed rotation, atomizing feeding, the liquid vale avoid leak through and high viscosity,

    特長：中速粘合混煉，霧化加液料，防滴漏耐高粘度液料閥， plc控制。
  5. Middle speed rotation, atomizing feeding, the liquid vale avoid leak through and high viscosity, plc control

    特長：中速粘合混煉，霧化加液料，防滴漏耐高粘度液料閥， plc控制。
  6. Double - shell heat energy storage microcapsule was prepared used the prosperities of microcapsules were investigated. a phase change material as core, which melt point was 24 c and phase transition heat was 225. 5j / g. the microcapsules would been used in indoor wall to regulate the temperature and saving energy sources. the surface morphological structure was examined by means of scanning electron microscopy

    其中當乳化速度為2500r min 、乳化時間大於5min 、壁材滴加速度小於0 . 5ml ? min ~ （ - 1 ）且系統調節劑為芯材的30 40時微膠囊的粒徑分佈集中； dsc顯示微膠囊包覆相變材料不影響其相變點，相變儲熱明顯。
  7. On the basis of consulting a large number of literatures domestic and aboard, the present situation and latest development of hydrodynamic characteristics of overland flow and slope erosion dynamic process were reviewed. aiming at revealing the effect of rainfall splash intensity on hydrodynamic features of sheet flow and slope erosion, with a combination of runoff experiment and simulated rainfall experiment with a fixed intensity, applying hydrodynamic and erosive theory, the effect of rainfall on overland flow velocity and the influence of rainfall splash intensity on hydrodynamic features ( such as velocity, flow depth, flow patterns, resistance ) of sheet flow on slope and the influence of rainfall splash intensity on the overland flow sediment contain was researched

    本文在查閱了大量國內外文獻資料，全面了解了坡面流水動力學特性及坡面侵蝕動力過程等方面的研究現狀及最新進展的基礎上，以揭示雨滴打擊動能對坡面薄層水流水動力學特性及坡面侵蝕的影響為目標，採用水槽放水試驗和定雨強模擬試驗相結合的方法，運用水動力學與侵蝕理論，研究了降雨對坡面薄層水流流速的影響，雨滴打擊強度對坡面薄層水流流速、水深、流態、阻力等水動力學參數的影響，雨滴擊濺作用對坡面流泥沙含量的影響。
分享友人
分享到 Line

分享到臉書