滾動位移 的英文怎麼說

中文拼音 [gǔndòngwèiyí]
滾動位移 英文
roll displacement
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  • 滾動 : roll; trundle; rolling; volution; run; rolling motion滾動半徑 rolling radius; 滾動傳感器 roll sen...
  1. The reason of rupture of driven shaft of idler wheel for some factory is analyzed

    摘要文章分析了某單位移動工位滾輪架從動軸的斷裂原因。
  2. Three types of adjustable turning rolls : manual lead screw adjusting, manual bolt shifting and electric sliding plate shifting

    可調式滾輪架有手動絲桿可調式、手動螺栓移位式和電動滑板移位式三種。
  3. When the scroll box is at the maximum value, the scroll box moves to the right - most or bottom position

    當滾動框的位置值為最大值時，滾動框移到最右端位置或底端位置。
  4. When the scroll box position is at the minimum value, it moves to the left - most position for horizontal scroll bars or the top position for vertical scroll bars

    值。當滾動框的位置值為最小值時，滾動框移到最左端位置（對於水平滾動條） ，或移到頂端位置（對於垂直滾動條） 。
  5. This article introduces one technique swayings mechanical contact whell based on hall componets to measure straight line long displacement

    為此提出了一種以擺動式機械接觸滾輪為基本原理，基於霍爾元件進行信號檢測的直線大位移測量方法。
  6. And then make out the nonlinear equations from the mathematics models, the results includes : the contact angler, contact distortion and axial distortion of each rolling element in the bearing

    求解兩種數學模型的非線性方程組，計算出軸承各滾動體在不同工況下內、外圈接觸角，接觸變形和軸承軸向、徑向位移等。
  7. When rotating into force, in accordance with the cam roller set displacement curve effort rotating turret, while the ramps along the rib rolling

    當入力軸旋轉時，凸輪滾子按照設定的位移曲線旋動出力轉塔，而同時又沿肋的斜面滾動。
  8. About key control the movement of the wheel, the wheel to seize the opportunity to make an appropriate position to obtain scores

    左右方向鍵控制滾輪的移動，把握時機使滾輪達到適當的位置以取得分數。
  9. Introduction : about key control the movement of the wheel, the wheel to seize the opportunity to make an appropriate position to obtain scores

    左右方向鍵控制滾輪的移動，把握時機使滾輪達到適當的位置以取得分數。
  10. 4. dicussing soil pressure ( supposed as p ) and level displacement ( supposed as s ) in condition that consideration time performance, the relation is p = ae, when the defomation of wall has evidently effect on the soil pressure. 5. the deformation of wall ( supposed as sw ) leads to soil layer sedimentation ( supposed as pw ), the research find pw = 1. 22sw 6. the artifical neural networks has vast and applied foreground in the information construcion of deep foundation excluding the accidental factor

    4 、探討了考慮時間效應的土壓力和位移關系曲線，認為在當墻體的變形對土壓力分佈產生明顯影響時，二者間的關系可用一指數函數來表達： p = ae ~ （ （ / s ） ） 5 、墻體側向變形，導致墻後土體產生沉降，在本次研究中，排除掉基坑降水施工因素的影響，由墻體變形導致的墻後土體沉降，二者具有p _ w = 1 . 22s _ w關系； 6 、將基於時間窗口滾動多步神經網路預測方法和應用於深基坑工程墻體變形的預測工作，具有較高的預測精度，該方法在巖土工程變形預測方法中具有廣泛的應用前景。
  11. When you add a control above or to the left of the scroll position, you must add the offset to the desired location

    如果添加的控制項在滾動位置的上方或左側，則必須在目標位置的基礎上加上該偏移量。
  12. Property is the number of positions the thumb moves in response to having the left or right arrow key pressed. the value of the

    >屬性值是滾動塊響應按下向左鍵或向右鍵時移動的位置數。
分享友人
分享到 Line

分享到臉書