滾壓成形 的英文怎麼說
中文拼音 [gǔnyāchéngxíng]
滾壓成形
英文
roll forming-
These modifications are usually in the form of surface deformations from embossing by rolls, fluted surfaces, and other fibers.
這些變化通常是受滾筒溝槽表面以及受其他纖維的擠壓形成表面變形。Numerical simulation analysis on extrusion molding of rings of tapered roller bearings
圓錐滾子軸承套圈擠壓成形數值模擬分析A research for roll - shaping helical bolts
螺旋釘滾壓成形研究This is a thread producing machine which uses its three thread rolling dies, mounted in the same seperation angle of 120 ', to realize roll forming of the workpiece, for metal has the performence of plastic deformation under the pressure operation
該機床是利用金屬在壓力之下產生塑性變形的特點，用三個互成120度夾角的滾模，對工件進行滾壓成型的螺紋加工設備Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。The technologies of rolling plasticity forming contain three traits which are simple, long life of cutter and high efficiency, especially, without pull - out fitment for the sloping gears forming
摘要運用滾壓成形技術進行齒輪塑性加工具有設備簡單，刀具壽命長及效率高的特點，尤其對料齒輪的成形加工，沒有拔模問題。The wire race is more likely to be destroyed in use, one of the main reasons is the elasti - plastic deformation between rolling ball and wire race during the contact process
在實際使用過程中發現作為滾道的鋼絲易發生破壞，而造成鋼絲破壞的主要原因之一就是滾動體與鋼絲在接觸過程中相互碾壓而發生的彈塑性變形。Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。Tannery machines. reciprocating roller machines. safety requirements
製革機械.往復式滾壓成形機.安全要求Abstract : the design essentialities of roll forming process was discussed in this paper. the design method ofroll forming process was analyzed through a real design instance
文摘:討論了滾壓成形工藝的設計要點。通過一個具體實例，分析了滾壓成形工藝的設計方法。This paper focus on principles of rolling plasticity forming and factors which are affected by cold press rolling and hot press rolling and anticipates to recognize the inherent law of rolling plasticity forming
主要對滾壓成形原理、冷擠及熱擠成形時的影響因素進行了分析與研究，期望能對認識滾壓成形技術的內在規律有所幫助。Analysis of ball spinning formability of thin - walled tubular parts of aluminum alloy
鋁合金薄壁筒滾珠旋壓成形分析Successfully simulated and replayed the complicated ball spinning of inner grooved tubes through the establishment of simplified sixth rotational symmetrical fe model and the adapting of local remeshing techniques
通過建立簡化的六分之一旋轉對稱模型和採用網格局部重劃分技術，成功地模擬和再現內螺紋管滾珠旋壓成形過程。Abstract : there are lots of advantages by cold extrusion for straight knurlnut in a single process
文摘:直紋滾花螺母採用冷擠壓一次成形新工藝，成效顯著。Theoretical calculation and simulation analysis on rolling contact area of external spline cold rolling
外花鍵冷滾壓精密成形滾壓接觸面積的計算與模擬分析分享友人