滾壓螺紋用模 的英文怎麼說

中文拼音 [gǔnyāluówényòngmó]
滾壓螺紋用模 英文
thread rolling die
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 壓 : 壓構詞成分。
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  • 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  1. In the construction of the tanghe inverted siphon on mid - roule of south - to - north water transfer project, some reliable construction processes and techniques are applied such as belt conveyor with three - rail gantry, construction with combined steel formwork, straight screw sleeve connection for reinforcement and the crushed stone - planting method etc., by which better construction effects are obtained

    摘要南水北調中線唐河倒虹吸工程項目施工中，根據工程特點，採用了三軌門架式皮帶布料機、鋼模板聯體施工、鋼筋滾壓直螺紋套筒連接、混凝土施工縫栽石法等可靠的施工技術和施工工藝，取得了較好的效果。
  2. This is a thread producing machine which uses its three thread rolling dies, mounted in the same seperation angle of 120 ', to realize roll forming of the workpiece, for metal has the performence of plastic deformation under the pressure operation

    該機床是利用金屬在壓力之下產生塑性變形的特點，用三個互成120度夾角的滾模，對工件進行滾壓成型的螺紋加工設備
  3. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
  4. Successfully simulated and replayed the complicated ball spinning of inner grooved tubes through the establishment of simplified sixth rotational symmetrical fe model and the adapting of local remeshing techniques

    通過建立簡化的六分之一旋轉對稱模型和採用網格局部重劃分技術，成功地模擬和再現內螺紋管滾珠旋壓成形過程。
分享友人
分享到 Line

分享到臉書