滾距 的英文怎麼說
中文拼音 [gǔnjù]
滾距
英文
gage thickness-
Gets or sets the size of the auto - scroll margin
獲取或設置自動滾動邊距的大小。Short - pitch transmission precision roller chains and bush chains
短齒距傳動精密傳動滾子鏈及套筒鏈Double - pitch precision roller chains and sprockets for transmission and conveyors
傳動及輸送用雙節距精密滾子鏈和鏈輪Fly straight and level form left to right as the helicopter is just about in front of the pilot, pull back cyclic, adjust the collective to maintain constant altitude and speed and hold the back cyclic as the helicopter completes one ( 1 ) full traveling tumbling back flip to upright
由左至右保持水平直線飛行,當直升機在操控者的正前方時,將升降舵拉升舵,控制主旋翼的螺距使直升機保持固定的高度及前進速度,向後翻滾一圈完畢。Fly straight and level from left to right at a moderate speed as the helicopter is just about in front of the pilot, add extra collective momentarily, then simultaneously push forward cyclic, and adjust the collective to maintain constant altitude and speed and hold the forward cyclic until the helicopter completes one ( 1 ) full traveling tumbling front flip to upright
由左至右保持適當速度的水平直線飛行,當直升機在操控者的正前方時,瞬間加大主旋翼的螺距,同時將升降舵打降舵,控制主旋翼的螺距使直升機保持固定的高度及前進速度,直到直升機向前翻滾一圈完畢。Railway transport equipment. wheel sets for standard gauge rolling stock nominal diameters at the rolling circle of wheels
鐵路運輸設備.標準軌距鐵路車輛的輪組.車輪軸滾動環部位的公稱直徑Conveyor belts. formula for transition distance on three equal length idler rollers. for coal mining
煤礦用帶式輸送機滾筒與相鄰槽形.托輥組之間的距離計算公式With the helicopter flying sideways nose - out straight and level from right to left, tumble the helicopter forward while traveling sideways, use collective to maintain altitude and speed across the ground, complete at least one ( 1 ) tumble
保持機尾朝向操控者,由右向左開始橫向水平飛行,將升降舵打降舵,控制主旋翼的螺距,使機體能保持固定的高度及橫向速度,至少完成一個前滾翻。With the helicopter flying sideways nose - out straight and level from right to left, roll the helicopter to the left ( the same direction as the helicopter is flying ), use collective to maintain altitude and speed across the ground, complete at least one ( 1 ) roll
保持機尾朝向操控者,由右向左開始橫向水平飛行,將副翼打左舵(與橫向飛行的方向同向) ,控制主旋翼的螺距,使機體能保持固定的高度及橫向速度,至少完成一個側滾。The outer hull of the wire has been moulded by rolling with small volume and pretty appearance to insure its enough flexibility and high carrent bearing. it can be installed under the circumstances of over six meters of span
1外殼採用冷軋鋼板一次性滾壓成型,外型美觀,大大增強母線抗彎強度,載荷性能強,適合於6米以上大跨距場所安裝。Transformers ; rollers ; center - line spacings and rail gauges
變壓器.滾子.中心距和軌距By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given
採用外點罰函數優化方法,通過取行星輪半徑和中心距之和作為優化目標函數,對滾錐齒超環面行星蝸桿傳動進行了參數優化,運用此優化程序,初步完成了對該種傳動的系列化研究,給出了傳動系列的最佳參數取值。A big swing and a slow roller towards short
大棒一揮,短距離的慢速滾地球. .Gets or sets the value added to or subtracted from the
獲取或設置當滾動框短距離移動時對Numerical analysis of backflow distance of smoke in mine fire
礦井火災煙流滾退距離的數值模擬Use roller to roll one of end of tape in order to adhere to tescified load on lower end. measure the distance of slide after a certain time. if drop it is time to evaluate tape ' s retention
將膠帶之一端以滾輪輾壓,使之粘于試驗板,一端懸吊規定之重量,經一定之時間后,量測膠帶下滑之距離,如中途掉落,則記錄時間,用以評定膠著保持力Short pitch transmission precision roller chains and chain wheels
短節距傳動用精密滾子鏈和鏈輪Short pitch transmission precision roller chains. heavy duty series
傳動用短節距精密滾子鏈.加重系列Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析,並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算,最後對誤差進行合成。Precision power transmission, double - pitch power transmission, and double - pitch conveyor roller chains, attachments and sprockets
精密動力傳輸雙螺距動力傳輸和雙螺距傳送機滾動傳送鏈連接件及鏈輪分享友人