滿對接焊 的英文怎麼說
中文拼音 [mǎnduìjiēhàn]
滿對接焊
英文
full penetration butt weld- 滿 : Ⅰ形容詞1 (全部充實; 達到容量的極點) full; filled; packed 2 (滿足) satisfied; contented; conte...
- 對 : Ⅰ動詞1 (回答) answer; reply 2 (對待; 對付) treat; cope with; counter 3 (朝; 向; 面對) be tr...
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
-
The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique
通過對其焊接性能的試驗研究,制定了該類鑄鋼件(磨耗板)的補焊工藝:低氫型堿性焊條,預熱與緩冷相結合的工藝措施,嚴格控制層間溫度( 250 ~ 300 )及焊接工藝規范,可獲得滿意的修復質量。As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers
本機床是電站大型汽輪發電機組的管道施工的關鍵設備,對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口,端平面,內外徑過緩斜度及直口,能滿足施工現場和製造廠家對各種管件的加工要求。What ' s more, the application of tc11 two phase alloys to the compress disk of areoengine alredy is relatively mature, and tc11 alloy may work safely for very long time below 500 c. ti3al matrix alloy and ( a + b ) two phase alloy is connected by weld. the request of the temperature and stress can be satisfied by dual alloy disk with isothermal forged ( or hot die forging )
選用ti _ 3al基合金tac - 1b和tc11兩相鈦合金用焊接工藝連接起來,通過熱模鍛或等溫鍛鍛造和不同的變形熱處理制度,製造出雙合金盤可以滿足溫度、應力對盤件的要求。The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed
再現分析得出的主要結論為:橋架的主樑上蓋板主焊縫的最大應力超過了許用應力,但小於屈服極限,可以繼續投入使用;副梁內部的應力遠遠超過了強度極限,變形特別嚴重,不能滿足生產要求,因此更換新的副梁;端梁內部的應力超過了屈服極限,小於強度極限,在應力較大的位置焊接補強板;投入使用后,要對整個橋架進行定期檢查。The latest generation of welding equipment can be programmed with specific process preferences of your individual choice or for the actual welding processes
最新一代的焊接設備能夠方便快速地對焊接參數進行個性化的設置,滿足您的常規焊接及其他特殊的焊接需求。This project use high voltage ignitor to solve the problem of interrupt. proved by experience, the output characteristic of this welding can be suitable to tech - guideline, and the inverter can work normally during arc welding process. the success ratio of ignition is also good enough
經實驗結果證明,該焊機輸出特性滿足技術指標的要求,焊接過程中不出現誤動作,引弧成功率較高,焊接性能穩定,對周圍環境有一定的抗干擾能力。To develop our intelligent arc welding off - line programming system and meet the needs of the remote welding application, the studies of the basic supporting techniques in the robotic offline programming and simulation system and the computer aided programming techniques in the arc welding application are carried out in this dissertation
智能化正成為離線編程系統的發展趨勢,為研製出智能化的弧焊離線編程系統及滿足遙控焊接的需要,本文針對機器人離線編程與模擬系統的基本支撐技術以及弧焊應用中的輔助編程技術進行了研究。So as to meet the new requirement of free - plumburm jointing of international copper foil coated panel and printing circuit board, our company introduces high quality blue kraft paper to meet the demand of the customers
針對國際覆銅板、線路板行業的無鉛化焊接要求的新規定,我司特推出此款藍色熱壓層墊紙以滿足客戶的要求。分享友人