漂儀計 的英文怎麼說
中文拼音 [biāoyíjì]
漂儀計
英文
driftmetre-
In general, a precise resistor is in series with one of the resistors in wheatstone bridge to compensate the zero offset, and the other one is in parallel with another arm of the wheatstone bridge to compensate thermal zero drift. based on this principle, in this paper, a compensation method based on virtual instrument technology has been put forward. actuated by current source, a good calculation method of compensation resistors and their position in the bridge is deduced
本文基於串並聯電阻補償法的原理，提出了一種基於虛擬儀器的誤差補償方案，推導了在恆流源供電下可以精確的計算出補償電阻大小和補償位置的演算法，並且在虛擬儀器軟體平臺labview上完成了數據採集、處理、顯示等軟體的設計，經過實驗的驗證，對傳感器的零點溫度漂移補償取得較好的效果，而對靈敏度溫度漂移的工藝補償亦有一定的效果。Thirdly, in the environment of labview, several kinds of vis used for sensor signal test are designed, including wave generation, time domain measurement, filter disposal, frequency analysis, etc. after that, wavelet analysis in the application of one - dimensional signal de - noise is studied, threshold and translation invariance wavelet de - noise are realized, and wavelet de - noise vi for zero drift signal of the fiber optic gyro in fcs is designed using labview
接著，在labview環境下開發了多種用於傳感器信號測試的虛擬儀器，具有波形發生、時域測量、濾波處理、頻譜分析等多種功能。隨后，研究了小波分析在一維信號消噪中的應用，實現了labview環境下的閾值法和平移不變量法小波消噪，並利用labview設計了飛控系統中光纖陀螺零漂信號的小波消噪儀。Mr. k. k. lau of the marine department recalled the challenge they faced when designing the buoy, " our buoys are mainly used for mounting relatively small and light navigation signs. the observatory s buoy posed a problem for us in that the weight of the equipment might make the buoy very unstable.
海事處劉家駒先生對設計浮漂氣象站時所面對的困難，印象深刻： 「我們沿用的浮標一直只能裝載較小和較輕的航海標記，由於天文臺的儀器較重，會使浮標不穩定，這令我們頗費思量。 」According to the principle of correlation detection, an automatic measurement system for extinction ratio of polarizer consisted of monochromator and dsp lock - in amplifier and compurer is designed not only to eliminate the influence on measurement accuracy caused by drift of intensity of light source but also to obatain approximate extinction spectrum
摘要基於相干檢測原理設計了一套由單色儀、數字鎖相放大器和計算機聯合使用的透射式偏光鏡消光比智能化測試實驗系統，採用雙頻雙光路分光單探測器接收鎖相放大器分離信號比對法進行源補償測量，克服了光源光強漂移所帶來的影響；實現了可見光區消光比的精確自動測量，而且可以測得近似的消光光譜。The results of calculation and evaluation showed that the main factors were the precision of standard curve and the excursion of instrument
對測量不確定度進行計算和評定，結果表明，影響其測量不確定度的主要因素是標準曲線精密度以及儀器漂移。2. based on interoferometric technique, a parasitic interference configuration was introduced to transpose the wavelength - shift signal into phase - shift signal ; the strains were demodulated by measuring the phase change of the signal with a phase - meter
利用干涉技術，採用寄生干涉結構對傳感光柵的反射譜進行波長解碼，用相位計觀測波長漂移引起干涉儀兩臂間相位差的變化，進而監測作用在傳感光柵上的待測應變量。The disease in jaw surface will be drop the bite force ; the bite force in the patient who disease in temporal jaw joint descent obviously than normal person ; serious mistake in join deformity, the acute damage in the area arthritis can also drop the bite force evidently ; compare to normal children, wenneberg fund that the bite force lower and the duration of the biggest bite force shorter in the children who fall ill of the chronic arthritis ; the bite force also be used in appraise of the recovery condition in surgical operation 、 disorder in jaw arthritis and the serious bone offset in bite lopsided etc. some materials, it will be produce polarization phenomenon inside when suffered some force in certain direction, at the same time, it produce opposite electric charge in two of the surface ; and resume to the station of on - electrification when removed the outside force ; change the direction of the outside force, the polarity of the electric charge also be changed, this kind of phenomenon is called as “ piezoelectric effect ”
本文設計了石英晶體壓電傳感器，以它作為傳感元件把咬合力信號轉變成電信號;利用ts5860型準靜態電荷放大器把傳感器的電荷信號轉變成電壓信號;選用usb7822數據採集卡，編寫該數據採集卡的驅動程序，採集該電壓信號並送到計算機里;編寫labview程序對該信號進行處理，得出咬合力值和咬合力曲線，並把測量結果以電子表格的形式保存，以便做進一步的分析和研究。通過對該測量儀的靜態標定、動態標定、溫度漂移標定以及實際測量試驗，證實了本測量儀具有較高的靈敏度、受動態力和溫度變化的影響比較小、能實時地顯示咬合力曲線和較準確地顯示咬合力值，滿足了咬合力測量的要求。The kinematic model of inertial measurement unit ( imu ) with mdrlg has been analyzed theoretically, the coning drift caused by dithering has been calculated, and some problems including the assembly of inertial sensors have been discussed
本文對機抖激光陀螺捷聯慣導系統慣性測量單元的運動模型進行了理論分析，對抖動作用下的圓錐漂移進行了理論計算，對儀表安裝形式等問題進行了探討。分享友人