潤滑間隙 的英文怎麼說
中文拼音 [rùngǔjiānxì]
潤滑間隙
英文
lubrication gap- 潤 : Ⅰ形容詞(細膩光滑; 滋潤) moist; smooth; sleek Ⅱ動詞1 (加油或水 使不幹枯) moisten; lubricate 2 ...
- 滑 : Ⅰ形容詞1 (光滑; 滑溜) slippery; smooth 2 (油滑; 狡詐) cunning; crafty; slippery Ⅱ動詞(貼著物...
- 間 : 間Ⅰ名詞1 (中間) between; among 2 (一定的空間或時間里) with a definite time or space 3 (一間...
- 隙 : 名詞1 (縫隙; 裂縫) crack; chink; crevice 2 (空閑) gap; interval 3 (漏洞; 機會) loophole; op...
- 潤滑 : [機械工程] lubricating; lubrication; lubricate
- 間隙 : (空隙) interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
-
Abstract : in this paper, an analytical study of the dynamics of the piston in a reciprocating internal combustion engine is conducted. the equations of reynolds and moving of piston are derived. a useful method of solution is obtained. the method is applied to s1100 diesel engine. the results of this study indicate that piston oil film is found to be sensitive to the piston - cylinder bore clearance, the location of the wrist pin and lubricant viscosity
文摘:對往復式內燃機活塞的動力特性進行了分析研究,導出了活塞潤滑的雷諾方程和活塞運動方程,給出了可供實用的求解方法,並採用這種計算方法對s1100柴油機進行了設計計算與試驗研究.研究結果表明,活塞潤滑油膜歷程與活塞& &缸套的間隙、活塞銷的位置、潤滑油的粘度等因素密切相關There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings
軸瓦內表面的不承擔載荷部分開有油槽,潤滑油通過進油孔和郵溝流進間隙。Lubricating spindles with narrow bearing clearance in machine tools
亦可用作潤滑機械工具中,狹窄間隙軸承的軸心。To ensure the charging pump working reliably, the following measures should be adopted : ( 1 ) adopting modified circular casing to reduce the radial force of the impeller and decrease the seal clearance ; ( 2 ) using radical ribs on impeller and helical sealing on shaft to realize minor pressure differential ; ( 3 ) using back pressure stuffing box to ensure sealing under small packing force ; ( 4 ) adopting self - lubricant flexible graphite stuffing for absorption of solids entering in the graphite in case of leaking
為確保灌注泵可靠工作,提出改進措施: ( 1 )採用改型環形泵體降低葉輪的徑向力,減小軸封間隙,抑制泄漏; ( 2 )採用背葉片降低葉片根部壓頭,獲得微壓,使軸封兩端承受較小壓差; ( 3 )採用螺旋密封降低軸封兩端壓差,在保持微壓的同時避免出現負壓,密封效果更好; ( 4 )採用反壓式填料密封結構,在很小的壓緊力下,即可保證密封; ( 5 )採用具有潤滑功效的柔性石墨填料,即使發生軸封泄漏,進入石墨內部的固相顆粒也將隨著石墨的消耗而被鉆井液吸收。For the case of static loaded er journal bearings, the influence of er effects on the lubrication performance are studied under various radius clearances, eccentricity ratios and shear rates
對于穩載電流變滑動軸承的潤滑問題,研究了不同平均間隙、不同偏心率以及不同剪切速率下電流變效應對軸承潤滑性能的影響。The numerical results show that : with the enhancement of er effects, the bearing capacity is obviously increased ; the increase magnitude is larger when small radius clearances and large eccentricity ratios ; at low shear rates, the influence of er effects on the lubrication performance of journal bearings are more obvious
數值研究表明:隨著電流變效應的增強,軸承潤滑油膜的承載能力明顯提高;軸承半徑間隙越小,偏心率越大,軸承承載能力增加的幅度也越大;在低剪切速率下,電流變效應對軸承潤滑性能的影響較大。Abstract : the main points of using and maintenance of isuzu nhr vehicle are described in this paper. the concrete contents include following points : checking of the oil level, braking fluid level and the tension of fan belt ; maintenance of the air cleaner and battery ; adjustment of the valve clearance and parking brake
文摘:闡述了五十鈴nhr貨車的使用與維護要點,即潤滑油油位的檢查;風扇皮帶撓度的檢查;空氣濾清器的維護;氣門間隙的調整;蓄電池的維護;駐車制動的調整及制動液液位的檢查等。The threshold speed and the typical characteristics of the oil whip of the system are simulated under the nonlinear model of oil film force, and the state of motion and type of the bifurcation are analyzed by floquet multiplicators which is computed by the shooting method. secondly, the the nonlinear dynamical model of the low - pressure rotor - bearing system by column bearing with reduced dimensions is presented. the numerical results show the rule of the amplitude with the eccentricity of rotor, the length - to - diameter ratio, oil viscosity and the clearance - to - radius ratio of the bearing under the definite speed
其次,對降維后的低壓轉子?軸承系統的非線性動力學方程,計算了圓柱瓦軸承支撐的轉子系統的振動穩定性在固定轉速下隨偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比的變化規律,並分析了轉子前軸承軸頸的失穩轉速與轉子偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比之間的關系,同時利用floquet理論分析其運動狀態和分岔類型。Numerical analysis of the influence of surface topography on head - disk lubrication
磁頭間隙潤滑影響的數值分析分享友人