濕空氣熱容 的英文怎麼說
中文拼音 [shīkōngqìrèróng]
濕空氣熱容
英文
humid heat capacity of air-
Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet - parameter on evaporator. fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio - parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping
本文的主要內容如下： 1 ）對翅片管蒸發器結構特點進行分析，選取適當的微元控制體，就干、濕和霜工況下對每個微元分別進行傳熱傳質分析，基於經驗關系式確定霜的有關參數，對于霜工況下的霜生長建立模型，經適當假設，運用質量守恆、能量守恆和動量守恆方程建立適合動態模擬的蒸發器數學模型，為系統模擬奠定基礎； 2 ）對蒸發在大擾動下的開、停機過程，運用動態集中參數模型進行分析和計算，為更好地描述製冷系統運行的全過程奠定基礎，同時也為製冷系統實現自動控制提供一定的理論基礎； 3 ）對蒸發器正常運行過程，運用動態分佈參數和參數間定量耦合的觀點來分析和計算，為更好地了解穩態工況下各點參數的變化情況及各入口參數對蒸發器動態特性的影響即蒸發器性能對各參數變化的敏感性； 4 ）編寫翅片管蒸發器動態特性模擬計算程序，可以計算不同邊界條件和初始條件下的製冷劑熱力參數、空氣溫濕度和霜厚度分佈場，實現對翅片管蒸發器在干、濕和霜工況下的動態模擬。In this paper, we aim at establish heat and mass coupled transfer model in the building wall, the emphasis of this study lies in creating a coupled and non - linear diferential equation system for the heat air and moisture transfer in the wall, which can be described by means of continuum mechanics and irreversible thermodynamics, the most dominant factor is moisture conten 9la gas pressure pc and temperature t, for the description of heatair and moisture transport, the general mass balance equation can be expressed by the temporal change of moisture conten 9 l, gas pressure pc and temperature t that means, in order to create a closed solvable equation system, the other additional dependencies have to be found, which the other variable depending on the variables of the solution : moisture conten 6 l gas pressure pc and temperature to the model is verified by the numerical simulation software which has been developed about building wall.,
根據節能設計要求，本文用熱力學的方法，並根據多孔介質中多相流體流動描述方面的最新研究成果? ?體積平均方程，建立了墻體熱、濕和空氣耦合熱質傳遞模型，並推導出熱、濕和空氣耦合傳遞等效擴散方程；找到建築墻體熱、濕及空氣耦合作用下熱質傳遞過程的主要影響因素濕容量_ l 、氣壓p _ c和溫度t 。開發了單體材料墻體熱質傳遞數值模擬軟體，用實測數據對軟體進行調試並對模擬計算結果進行了驗證。模擬出了單材料墻體在熱、濕和空氣耦合作用下建築墻體內的溫度和濕度分佈規律。Ln chapter 4, imbalanced counterflow of indirect evaporative cooling is simulated while taking into account the non - linearity of the saturation line of moist air. four diagrams are provided to assist in determination of the optimum heat capacity ratio
第四章針對蒸發冷卻過程中飽和濕空氣比熱容隨溫度的非線性變化關系，研究了非平衡流逆流間接蒸發冷卻過程（火用）損失及最佳熱容量比的計算線圖。
分享友人