濺水型 的英文怎麼說
中文拼音 [jiànshuǐxíng]
濺水型
英文
splash type-
Gully erosion, which is universal on original lands, but also the special forms, for example, hole erosion gravel erosion debris slide and debris flow, which is unusual in loess area, ( 2 ) based on a long - term fixed point experiments in proving ground of the south stackpile, the soil erosion factors have been researched quantitatively, the runoff and erosion affected factors have been made sure and the experiential models of producing water and soil have been taken in newly - constructed stage, early stage and later stage of reclamation
確定南排土場原地貌的水蝕模數為3700 4400t km ~ 2 ? a ；在排土場新造地貌上，擊濺、面蝕、細溝侵蝕、淺溝侵蝕、沉陷侵蝕、砂礫化面蝕、土砂瀉溜和坡面泥石流等水土流失形式出現頻率和發生程度都明顯強于原地貌。 （ 2 ）以南排土場徑流試驗場長期的定位觀測為基礎，對排土場未復墾時期、復墾初期、復墾後期的土壤水蝕影響因子進行定量研究，確定了徑流和土壤水蝕的主要影響因子及其臨界值，建立了產流產沙的經驗模型。This thesis will put forward a new design project that aimed at discussing the packing sets of natural - draft counter - flow dry cooling tower, which is the research and application of the spray nozzle. the content mainly includes the experimental study of the application of the jnx - 01 spray nozzle in cooling tower, as well as the heating calculation
本文將針對自然通風逆流濕冷式冷卻塔中影響效率較大的淋水裝置提出設計改進方案，即旋轉式噴濺裝置的研究與應用，內容主要包括jnx - 01型節能旋轉式噴濺裝置及旋轉濺水碟式噴頭在冷卻塔上應用情況的試驗研究及熱力計算。Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead
通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定The water spray from long heavy vehicles can impair vision
長車重型車輛濺起的水花，足以阻礙視。Scanning electron microscopy : after fixed in 2. 5 % glutaraldehyde made up in 0. 1 m phosphate buffer ( ph 7. 2 ), the tissue of testis was post - fixed in 1. 0 % oso4, dehydrated in a progressive ethanol solution, dried and sputter - coated with gold, then observed with kyky - 1000b microscopy and photographed
掃描電鏡樣品以2 . 5戊二醛（ ph7 . 2 ， 0 . 1m lpbs緩沖液配製）和1鋨酸雙固定，酒精系列脫水，乾燥，真空離子濺射儀噴金， kyky - 1000b型掃描電鏡觀察並拍照。The hillslope erosion processes include soil separation, sediment transport and sediment precipitate, which these three process result from the rainfall splash erosion and runoff erosion. to study and analyze the happening and developing conditions of hydraulic, soil and terrain, and the mechanisms of transitions and influences of these processes each other is the prerequisite to set up physical model of soil erosion
坡面侵蝕過程包括降雨濺擊和徑流沖刷引起的土壤分離、泥沙輸移和沉積3大過程，研究和分析這些過程發生、發展的水力、土壤、地形條件以及各過程間相互轉化、相互影響的機理，是建立土壤侵蝕物理模型的前提條件。Wuxi nakano machinery co., ltd. and japan - field technology, the development of a new type of closed turntable polishing concrete slabs. polished tiles from the radically changed the cooling water production accelerated, workers unable to operate close to the phenomenon ; supported by tanks under the workpiece table, it will not only compensate for the loss millstone, but stable grinding force. different uniform surface quality products ; with the grinding process workpiece turntable and rotating products
無錫中野機械有限公司引進日本技術，全新開發的轉臺型封閉式混凝土地磚磨光機，從根本上改變了磨光地磚生產中冷卻水飛濺，操作工人無法靠近的現象工件轉臺由下油缸支承，不僅能及時補償磨石的損耗，而且磨削力穩定不變，不同產品的表面質量均勻一致磨削過程中產品隨著工件轉臺而轉動，避免了其它型式磨光地磚生產中產品不動而帶來的同一產品表面質量不均的現象。分享友人