火花放電隙 的英文怎麼說

中文拼音 [huǒhuāfàngdiànxì]
火花放電隙 英文
airgap
  • 火 : fire
  • 花 : Ⅰ名詞1 （種子植物的有性繁殖器官） flower; blossom; bloom 2 （可供觀賞的植物） flower 3 （形狀像花...
  • 放 : releaseset freelet go
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 火花 : spark; spark discharge; spark-over; scintillance; flake; trigatron; cremation; [電工] electric spark
  • 放電 : [物理學] （electric） discharge; electro-discharge; discharging
  1. Study on volt - ampere properties in wedm

    電火花線切割加工中放電間隙伏安特性的研究
  2. Nowadays, the switches which are being studied or applied, such as gas spark gap, thyratron and ignitron, etc, are of different structures, operating principles, advantages and disadvantages, and are applied in various situations and fields

    目前處于試驗中或者投入實際應用的開關元件很多，如火花放電間隙、閘流管、引燃管等，它們有不同的結構、原理和優缺點，應用在不同的場合和領域。
  3. Incondition of surface anti - corrision and insulation coat of metal and tiny hole of steel where resistance and crack is very small, when supplying a high voltage, gas crack will be punctured and electric spark discharging will occur, now send a pulse signal to the alarming circuit the alarmer can send out sound and light to alarm. we can do leak hunting on the coating according to this principle

    金屬表面絕緣防腐層過薄、漏鐵及漏電微孔處的電阻值和氣隙密度都很小，當有高壓經過時就形成氣隙擊穿而產生火花放電，給報警電路產生一個脈沖信號，報警器發出聲光報警，根據這一原理達到防腐層檢漏目的。
  4. Triggered spark gap

    觸發火花隙觸發放電器
  5. By using a counter and an operation microprocessor, this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state. this instrument takes samples of voltage, current signal and strong and weak of high frequency signals of detecting voltage amplitude, translates them into various time pulses in discharging state. and a counting unit turns these pulses into digital signals, then send them to a microprocessor. finally various discharge time percentages are sent to the control tache

    通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱，得出反映間隙放電狀態的各種時間脈沖，利用計數器分別對其計數，再送給單片機運算處理，輸出控制環節所需的各種放電狀態時間百分數。
  6. Abstract : by using a counter and an operation microprocessor, this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state. this instrument takes samples of voltage, current signal and strong and weak of high frequency signals of detecting voltage amplitude, translates them into various time pulses in discharging state. and a counting unit turns these pulses into digital signals, then send them to a microprocessor. finally various discharge time percentages are sent to the control tache

    文摘:通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱，得出反映間隙放電狀態的各種時間脈沖，利用計數器分別對其計數，再送給單片機運算處理，輸出控制環節所需的各種放電狀態時間百分數。
  7. According to the state of discharge gap, combining database technology, we adopt neuro - fuzzy control technology to realize real - time control of edm process and auto - adjustment on the basis of process state, which ensure the process is in the state of optimization

    依據放電間隙狀況，通過採用神經模糊控制智能技術，並結合數據庫技術，對電火花成型加工過程進行實時控制，根據加工狀態自動進行調節，保證了加工過程處于優化狀態。
  8. Abstract : on the basis of that the proportion of time spent sparking is analyzed in electrical discharge machining ( edm ) process, a new method. which is used to ascertain the trend of discharge gap change, is presented. and a fuzzy control strtegy is introduced to parctical use, the results is well

    文摘:通過對電火花成形機放電狀態的分析，提出了利用分析周期內出現異常放電狀態時間的比例及開路狀態所佔時間的比例，來判別電火花成形加工的間隙放電狀態及其變化趨勢的方法，並在此基礎上利用模糊控制策略實現了對電火花成形加工過程中放電狀態的控制，取得了令人滿意的效果。
分享友人
分享到 Line

分享到臉書