烘缸 的英文怎麼說

中文拼音 [hōnggāng]
烘缸 英文
dryer
  • 烘 : 動詞1. （使熱; 使干） dry or warm by the fire 2. （襯托） set off
  • 缸 : 名詞1. （盛東西的器物） jar; jug; vat; crock 2. （缸瓦） earthenware with crude glaze 3. （像缸的器物） jar-like things
  1. Dynamic balancing of rolls and dryers of paper machine

    造紙機械輥筒與烘缸動平衡
  2. For the stress analysis of dryers under the line load of supporting rollers, according to hoff theoretical solution of thin cylindrical shell under line loads, mangelsdorf approximate solution is modified on the basis of the calculation analysis for 14 sets dryers " dimension by computer programming with matlab software. the approximate formulas of the second largest hoop stress of the middle section of the shell are derived

    針對托輥線壓載荷作用下烘缸的受力分析，本文根據薄壁圓柱殼在線壓載荷作用下的hoff理論解，在運用matlab軟體對14組常用烘缸參數進行編程計算分析的基礎上，對mangelsdorf近似解作了修正，並由最小二乘法導出殼體中部截面環向應力次大值的近似計算式。
  3. Design standard in cast iron dryers used in paper machinery

    造紙機械用鑄鐵烘缸設計規定
  4. Technological condition of steel dryers used in paper machinery

    造紙機械用鋼制烘缸技術條件
  5. Technological condition of cast iron dryers used in paper machinery

    造紙機械用鑄鐵烘缸技術條件
  6. The application and study of a rotor fault diagnosis system of self - manufacture in the dry jar running system of paper machine

    自製轉子故障診斷系統在紙機烘缸轉動系統中的應用
  7. This paper introduces that turbulence generating bars installed on the nanping pm3 & pm4 ( 3 150mm ) and their running effect

    摘要介紹南紙（上標# ） 3 、 （上標# ） 43150紙機在烘缸內安裝破水棒的實踐經驗及其運行效果。
  8. According to the stress calculation of bolts of all common kinds of dryers with this model, the design method of bolts is put forward

    由該計算模型計算獲得國內所有常用規格烘缸的螺栓力，據此提出螺栓設計計算的方法。
  9. Cast iron dryers, which are classified to special cast iron pressure vessels, have been applied in paper drying in papering industry all over the world

    鑄鐵烘缸屬特種鑄鐵壓力容器，廣泛運用於造紙工業中的紙幅乾燥，產品遍布全國各地。
  10. After the study on the characteristic of the fatigue behavior of gray cast iron dryer, the fatigue analysis on this kind of dryer is carried out so as to specify the fatigue analysis method of dryers

    本文還在分析灰口鑄鐵烘缸疲勞特性的基礎上，對該烘缸進行疲勞分析，以此說明烘缸疲勞分析設計的方法。
  11. In this paper, owing to the gross deficiencies of the design method and code of dryers, the stress status of dryers under the working condition is analyzed in detail and the reasonable, reliable methods of the designing calculation are studied

    本文圍繞我國鑄鐵烘缸現行設計方法和設計標準中所存在的一些重大不足，全面分析烘缸在工作狀態下的受力狀況，並在此基礎上研究烘缸合理、可靠的設計計算方法。
  12. Further more, the fracture possibility is analyzed with fracture mechanics after the stress calculation of local high stress area around the bolt hole in shell flange and the measurement of fracture toughness of gray cast iron. the improving structure of bolts connected head and shell flange is brought forward

    此外，在計算獲得缸體法蘭螺栓孔局部高應力區的應力水平后，由斷裂力學分析發生脆性斷裂的可能性，並提出烘缸缸體與缸蓋聯接結構的改進方案。
  13. By use of this theoretical solution, the stress for various dryers with different pyramidal neck dimension is solved to study the influencing of dimension change on the stress level, from that the design request of the dimension of this transitional structure is put forward

    通過運用本理論解法對各規格烘缸不同錐頸過渡尺寸的應力求解，研究錐頸過渡尺寸對該結構段應力水平的影響情況，並由此提出過渡結構尺寸設計的要點。
  14. Right now, though, grab an ann taylor vest for 10 before they re gone for good

    而市面上的自助洗衣店每洗烘一缸臟衣，多的需付費六七個美元。
  15. At first, one kind of finite element model which is more accurate than the union model used before is set up to simulate the mutual contact between head and shell flange well. the stress analysis and measurement of the most typical and common dryers are done, from that the rightness of the calculative model is verified and the stress distribution of dryers under the inner pressure is got

    首先建立了一種更為精確地模擬缸蓋與缸體法蘭間相互接觸狀況的烘缸有限元計算模型，對國內最具代表性、最常用的烘缸運用該模型進行應力分析和應力實測，由此驗證計算模型的正確性，同時獲得烘缸在內壓作用下的應力分佈狀況。
  16. The calculating mold consisted of shell, pyramidal neck of shell with varied thickness, flange of ring with definite thickness for analytic solution is set up for the strength calculation and the design of the structure dimension of shell flange and pyramidal neck. this theoretic solution is compared with the results of finite element analysis and stress - strain measurement and is verified to be right

    為設計計算烘缸法蘭及錐頸的強度與結構尺寸要求，建立以簡體、具有斜面的變厚度圓柱殼的錐頸及具有一定厚度圓環的法蘭環為解析解的計算模型，進行應力求解，將該理論解與有限元分析及應力應變實測結果進行分析對比，驗證該解結果的正確性。
  17. After a dryer with a inner shell connected with two heads is analyzed with finite element method, the difference of stress distribution between this kind of dryer with common one is examined and the feasibility of utilizing the highest and lowest stress calculation formulas derived in this paper is studied

    通過對一帶內拉筒結構烘缸在線壓載荷作用下的有限元應力分析，研究該類結構烘缸的應力分佈狀況與普通型烘缸的差異及運用本文導出計算式進行最高和最低應力計算的可行性。
分享友人
分享到 Line

分享到臉書