焊口設計 的英文怎麼說

中文拼音 [hànkǒushèjì]
焊口設計 英文
joint design
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 設計 : devise; project; plan; design; excogitation; layout; layout work; styling
  1. During the course of the manufacture for packaging 2000 pixel hgcdte irfpa wafer, some crucial techniques are solved, such as the design of the button stem structures with inclined dragging wires applied in cryogenic platform, the optimization of long linear irfpa detector ' s signal wires layouts, the implement of a fanout board having thin film gold metalization for defining the required electrical conductors and a method of hermetically sealed vacuum enclosure of large dimension windows, etc

    在用於封裝2000元碲鎘汞焦平面晶元的分置式微型杜瓦研製中，詳細闡明了一種焦平面晶元其裝載面為斜拉式支撐結構的設計，實現了探測器外引功能線的布線優化及其輸出引線工藝改進，並提出了一種大尺寸高氣密光學窗口的焊接方法等關鍵技術。
  2. To meet this challenge, a research project was supported by ministry of communication and bv shanghai zhenhua port machinery co. ltd. focusing on analysis of tdtcd ( traditional design theories of crane drums ) the paper has studied the impacts of features under the binding force of wire ropes, the end - plate and rope slot. this study is based not only on the thin shell theory and viscoelastic mechanics to calculate the strength and stability of drum, but also on an experiment with technology in " state of act "

    本文結合交通部重點科技項目「港口起重機鋼絲繩傳動件高性能技術研究」和上海振華港機股份有限公司委託項目「起重機焊接捲筒極限壁厚研究」 ，針對起重機捲筒傳統設計方法偏於保守的情況，以薄殼理論和近代力學為基礎，以現代試驗技術為研究手段，對鋼絲繩緊箍力作用下的外載特性、端板、繩槽等因素對捲筒強度和穩定性的影響進行了系統的理論研究，在深入開展捲筒強度、穩定性和實驗模態分析等試驗的基礎上，提出了有別于傳統方法的捲筒強度、穩定性計算方法。
  3. 1 process - oriented algorithms for sheet metal deployment. an investigation is made on the constrains to welded seam, sheet thickness, slope type and their influences to sheet metal manufacture process, and a rational method is adopted to treat design and calculation

    本文主要涉及的研究內容及創新點包括以下幾個方面： 1 、提出並實現了面向工藝的鈑金展開演算法；探討了展開計算時焊縫邊界約束條件，板厚處理，坡口型式對鈑金加工製造工藝的影響，並採用合理的方法進行處理和設計。
  4. It can make fuqq soldering on any parts and boards by applying adjusted design on the height of spout

    噴口高低采可調式設計，對任何零件機板，均能作「完全錫焊」 。
  5. And it can make full soldering on any parts and boards by applying adjusted design on the height of spout

    噴口采可調式設計，對任何零件機板，均能作「完全錫焊」 。
  6. At present, company has two fabrication lines specially designed for welding h section, advanced cutting, welding, assembling, rectifying, digital controlled hole drilling machine, blasting and coating facilities, level ii steel structure design software x - steel ( originated from finland ) and pkpm

    目前擁有焊接h型重鋼生產線兩條，擁有先進的切割、焊接、組立、矯正、數控制孔、拋丸、噴塗等設備；擁有先進的鋼結構二次設計專業軟體x - steel （芬蘭進口）和pkpm 。
  7. The results show that : the strength and fatigue lifetime of the outer casing including welding line can satisfy the design requirement. although the some parts of bearing has been yielded, the strength at the weld is large enough for requirement. and welding defect, indicted by sem analyses of failure section, is main reason affecting fatigue lifetime

    分析結果表明：外機匣（包含焊縫）強度和壽命滿足設計強度和壽命的要求；軸承座的強度已經進入屈服階段，而軸承座及其焊縫處的壽命卻是滿足設計壽命要求；另外斷口的金相分析表明焊接缺陷的存在是影響疲勞壽命的主要原因之一，故需提高焊接技術，減少焊接缺陷的存在以提高焊接結構的壽命。
  8. A vision sensing system designed is applied to the abb robot. the system consists of vision sensor, image preprocessing and seam recognizing system, serial port communication and abb robot executive unit

    本文設計了一套視覺傳感系統應用於abb的弧焊機器人，該系統有視覺傳感器、圖象預處理及偏差識別系統，串口通信和abb機器人執行機構。
  9. We have a wide selection of high - quality coffins, urn, pet caskets, and novel style coffin - shaped crafts or furniture. concerning electric products, we lead a group of factories to supply products which all meet international standard, including switch cabinet, meter trunk, waterproof box, steel frames and such

    公司主營殯葬類木製品，木製工藝品以及各類五金交電，主要包括配電櫃，儀表盤的密閉箱體及各式鋼結構設計焊接製造的出口和內銷，是一家集產品開發，生產，銷售於一體的綜合性實體企業
分享友人
分享到 Line

分享到臉書