焊后狀態 的英文怎麼說

中文拼音 [hànhòuzhuàngtài]
焊后狀態 英文
as-welded
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 狀態 : status; state; condition; state of affairs: （病的）危險狀態 critical condition; 戰爭狀態 state o...
  1. By compared with the simulation results and the experiment results, we come to the conclusions that : ( 1 ) circuit with assistant network can widen soft - switching extent in lagging arm, reduces duty - cycle loss on the secondary, diminishes switching dissipation of inverter spot - welding power source. ( 2 ) the range of resonant capacitor, the important factor to soft - switching process, not only affects zero - voltage turn - off of power switches, but also affects the range of zero - voltage turn - on of power switches. so resonant capacitors must be considered according to many aspects ; ( 3 ) it easily fulfils soft - switching condition in lagging arm as leakage inductance of power transformer increases, but bigger leakage inductance of power transformer increases opening dissipation of transformer and decreases efficiency of soft - switching inverter power source

    通過模擬結果與軟開關點焊逆變器試驗結果的對比分析，得到了如下主要結論：採用輔助網路可以完全拓寬全橋軟開關逆變器的滯后橋臂軟開關范圍，減小了次級占空比丟失，降低了逆變電阻點焊電源的開關損耗；諧振電容是影響軟開關工作狀態的重要因素，其大小不僅影響開關管的零電壓關斷，同時也影響開關管的零電壓開通范圍，因此，諧振電容應該綜合考慮；功率變壓器漏感越大，越容易滿足滯后橋臂的軟開關條件，但是大的漏感也使變壓器的通態損耗增加，降低了軟開關逆變器的效率。
  2. About design programs of propylene tower post weld whole heat treatment, we have made analyses and compare from the various technical and economic aspects, and in vertical state of large pressurized vessel, we propose to adopt the internal combustion heat treatment method, in horizontal state of it, to adopt high temperature flue gas heat treatment method, and propose center combustion tube method as the future direction of technical developmnet insights

    摘要圍繞丙烯塔焊后整體熱處理的各種設計方案，從技術、經濟等方面進行分析對比，提出對超大型壓力容器，立置狀態下宜採用內燃法熱處理；臥置狀態時宜採用高溫煙氣法熱處理，並提出將中心燃燒管法作為今後技術發展方向的見解。
  3. These rules consist of the total fit, the mathematics and fatigue physics, and the safety in tail predictions. an analysis of the test s - n data of 16mn steel weld joints reveals that the four models are reasonable if only considering the total fit as the conventional method did. but if by the present three rules, the appropriate models should be the normal or the extreme maximum value

    根據先前提出的有限數據下良好假設分佈的確定方法，包括三個原則，即假設分佈形狀與誤差數據真實分佈形狀的一致性、預測的總體擬合效果、與疲勞失效機制的一致性和尾部預測的安全性，通過對線性均值s - n曲線擬合16mn鋼焊接頭s - n數據誤差的統計分析，說明應用一般推斷方法， 4種分佈都可合理地作為數據的統計模型，綜合考慮三原則后，極大值和正態分佈是可能的良好假設分佈。
  4. Remove excess solder with small brush while plastic, leaving a fillet around end of valve as it cools

    當焊料處于粘滯狀態時，用刷子把多餘的焊料清除干凈。焊料冷卻后，將一條嵌條環繞在閥門的埠。
分享友人
分享到 Line

分享到臉書