焊接了的 的英文怎麼說

中文拼音 [hànjiēlēde]
焊接了的 英文
welded
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 了 : 了助詞1. （用在動詞或形容詞后, 表示動作或變化已經完成） 2. （用在句子的末尾或句中停頓處, 表示變化, 表示出現新的情況, 表示催促或勸止）
  • 的 : 4次方是 The fourth power of 2 is direction
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. Abstract : for analyzing the residual stress distributing state within the weld joint, and its effect on the performance of welding structure, when welding the ferrite pearlite steel with the austenite steel, this paper develops a finite element program to compute the interface stress of two or over two material. finally, this program is used to analyze the mechanical behavior of heterogenic joint

    文摘:為了分析鐵素體、珠光體類鋼與奧氏體類鋼焊接時，焊接接頭處焊接殘余應力的分佈狀態及其對焊接構件性能的影響，研製了可計算兩種或兩種以上材料界面應力的有限元程序，並用此程序分析了異質接頭的力學行為。
  3. Before repairing, basing on the actual working condition, concerning the weldability, stress and deformation issues, the scheme of the cold welding technology whose essential being gtaw, low temperature preheating, postweld hammer the welded seam was established

    修理前，圍繞兼顧解決焊接性、應力和變形問題，結合實際施工條件制定了以手工鎢極氬弧焊、鎳基焊絲、焊前低溫預熱、焊后錘擊焊縫為要素的冷堆焊工藝。
  4. A resistance meander wire usually of constantan is welded onto a strip of foil

    在金屬薄片上焊接了改良的電阻導線，通常使用的是康銅導線。
  5. Fourth, the paper treats two kinds of hoisting projects of high alititude construction in bulk and member assembly, hositing machine and plan layout, setting up scaffold and joints, and installing trunks, branches and joints etc. then in detail discusses the method which applys total station to measure three - dimensional coordinate of dendriform structure, including selecting survey sign points, creating survey system and converting survey coordinate system etc. the paper also deep research on the welding performance, welding method, welding process, welding stress and control, welding strain and rectification, weld defects analysis and weld quality inspection, and so on complicated heterogeneity steel weld proplems

    接著系統的論述了高空散裝法和分單元安裝法兩種樹狀結構吊裝方案，樹狀結構吊裝機械及平面布置，樹狀結構胎架及節點的搭設，以及樹狀結構樹干、樹枝和節點的吊裝工藝等諸多工藝問題。詳細的論述了採用全站儀對樹狀結構進行空間三維坐標測量的方法，包括測量標志點的選取、測量系統的建立及測量坐標的轉換等問題。深入地研究了樹狀結構可焊性、焊接方法、焊接工藝、焊接應力及控制、焊接變形及矯正、焊接缺陷分析及焊接質量檢查等復雜的異種鋼焊接問題。
  6. In order to study the characteristic signals according to the quality of the welding with dissimilar gaps, the self - made real - time monitoring system with coaxial sensors is applied to acquire and extract coaxial signal, and then the signals are analyzed with modes analysis, subsection power analysis and wavelet analysis

    摘要為了研究不同間隙下激光拼焊的焊縫質量及其對應的信號特徵，採用自製同軸傳感系統採集提取多種間隙下焊接時的同軸光信號，並對信號進行眾數分析、分段功率譜分析和小波分析。
  7. The local geometric details considered include longitudinal length and height of access hole in beam web ; material nonlinearity and geometric nonlinearity are included in nonlinear analyses

    節點局部構造的變化主要考慮梁腹板上的焊接孔的長度和高度的改變，非線性分析包括了對材料非線性和幾何非線性的考慮。
  8. Therefore, in order to understand the long - time performance of the weld, it is necessary to study the welding interface of niobium alloy and stainless steel, and know the microstructure evaluation. explosive welding and vacuum electron beam self - material brazing were used to prepare the specimen

    因此，研究鈮合金與不銹鋼的焊接結合層，分析形成的互擴散層的組織、成分和性能變化，對了解不銹鋼和nb合金的互擴散反應行為，焊接件的焊接工藝改進和長期使用性能的評估是很有意義的。
  9. The natural vibration spectrum curve is measured and the critical velocity to induce trashrack bar galloping is calculated. the effect of bar spacing on the bar strain and the characteristics of the exciting force are discussed. by fatigue analysis it is obtained that the service life of weld at the fixed end of the bar is about 13

    分析了發電工況和抽水工況時的振源特性，討論了柵條凈距對柵條應變的影響，按鋼結構設計規范對柵條進行了疲勞計算， 1 ~ #測點處可視為不會發生疲勞破壞， 2 ~ #測點焊接處的疲勞壽命約為13 . 6年。
  10. Ultrasonic wire bonding was applied to connect the contacts and sub - miniature - a ( sma ) connectors. also a suitable shield box has been designed for the test of hts filters

    對于超導濾波器的焊接，採用超聲點焊焊接sma的接頭和高溫超導濾波器的接觸電極，實現了較小的接觸電阻和較好的機械強度。
  11. Comparing shear strength of different welded fabrics and concerning the microstructure of welds welded with different parameters, the relationship between shear strength and microstructure was studied

    摘要比較了具有不同焊接參數的鋼筋焊接網的剪切力曲線，分析了不同焊接參數所對應的微觀組織及其成因，研究了鋼筋焊接網的剪切性能和微觀組織之間的關系。
  12. Abstract : the use of reinforcing steel welding mat in engineering construction requires special purpuse welding machine. this article introduces the structure design and work principle of the gwc series mat reinforcement automatic welding machine in briefing

    文摘:工程建設中鋼筋焊接網的引入應用，對專用焊接設備提出了需求，本文簡要介紹我廠開發的gwc系列鋼筋網自動焊接成型設備的結構設計和工作原理。
  13. And the finite element method ( fem ) was used to simulate the stress and deformation of the outer casing and the bearing chock. on the basis of the experiments and fem analysis, the strength and fatigue lifetime, the interaction of creep and fatigue lifetime, the creep lifetime of outer casing and bearing chock have been analyzed, at the end of trail, sem analyses of failure section has been conducted

    同時對航空發動機燃氣渦輪外機匣和軸承座進行了有限元模擬計算，得到外機匣和軸承座的焊接處的強度和變形情況的模擬結果。根據試驗數據和有限元的計算結果，對發動機燃燒室外機匣和軸承座兩種結構（包含焊縫）進行靜強度分析、疲勞壽命分析、蠕變壽命分析、蠕變疲勞交互作用壽命分析以及斷口的金相分析。
  14. The other way, theoretical analysis of weld tracking system with a leading sensor is stated, based on the analyzing of movement process of the tracking system, a loop control structure diagram is presented, the deuce vision feedback system is used and realized the repeated and automatic tracking in multiplayer seam and controlling of system of tracking and system of motion

    同時就傳感器超前檢測式焊縫自動跟蹤系統進行了深入的理論分析，在分析該系統跟蹤過程運動關系的基礎上，建立了系統的閉環控制關系圖，並提出了其系統數學離散控制結構簡化圖。採用兩點式視覺伺服反饋系統，實現機器人在多層多道焊接時的重復自動跟蹤以及跟蹤機構的控制和焊炬橫向調節機構的控制，並使之協調聯動，滿足焊接過程的要求。
  15. The car has had a new wing welded on

    這輛汽車焊接了一個新的翼子板。
  16. Arc welding technologies in japan have been advanced steadily since the time when an application of covered electrodes was first examined in the shipbuilding industry about 90 years ago. the history of the arc welding technology has always been the history of the pursuit of higher " efficiency and speed " of welding processes welding materials, originally started with covered electrodes ， have been developed into more efficient submerged arc welding materials and gas ? shielded arc welding materials with which automatic welding and robotic welding can easily be conducted. the gas ? shielded arc welding materials can be classified mainly into solid wires and flux ? cored wires ( fcws ), and of these wires ， fcw has been increasing in uses year by year because of its excellent workability and efficiency. this article describes the recent trends in the development of fcws which now hold the major position in the welding materials. a special focus is put on the fcws for carbon steels

    90年前，日本的造船業開始使用藥皮焊條.自此，日本的弧焊技術取得了長足進步.弧焊技術的歷史是焊接工藝"高速度、高效率"的歷史.自藥皮焊條開始焊接材料已發展成為更高效的埋弧焊焊材和氣保焊焊材，並能更容易地結合自動化焊接和機器人焊接.氣保焊焊材主要分為實芯焊絲和藥芯焊絲，藥芯焊絲的應用因其出色的實用性和效率而逐年增加.介紹了藥芯焊絲作為主要焊材的發展趨勢，尤其是在碳鋼焊接上的應用
  17. Abstract : ultrasonic welding for ribbon is widely used in developed countries ， electric resistance welding is still used in china. on absorbing foreign advanced technology ， the key assembly of the ultrasonic welding machine i. e. pneumatic working platform was manufatured. the cost of the machine and its spare parts is only 1 / 3 of the imports. the machine has been operated in a factory for four years ， and has been proved stable and reliable. the machine can substitute the imports

    文摘:超聲波焊接是發達國家色帶生產企業普遍採用的色帶焊接方法，而國內企業均採用落後的電阻絲焊.為此，在吸收消化國外先進技術的基礎上，自行開發了色帶焊接機的關鍵部件? ?氣動工作臺，實現了超聲波色帶焊接機的國產化，整機及配件價格不到進口產品的1 / 3 .產品經工廠4年多的實際應用，性能穩定、可靠，完全可替代進口
  18. In this paper. monte carlo ( mc ) technique was used to simulate the grain growth in heat - affected zone of an ultra - fine grain steel

    本文採用montecarlo （ mc ）模擬技術對超細晶粒鋼鐵材料焊接haz的奧氏體晶粒長大進行了研究。
  19. Taking the example in the three gorges hydroelectric station, we researched the influence of the weld process on the construction and operation of penstock after moving contract - elongate nodes, analyzed the deformation law of two plans and calculated the crosswise and lengthwise shrinkage in weld process using experience formula and theory respectively, and then analyzed the influence of the welding and installing process on shrinkage, finally chose the best installation plan

    摘要以三峽水電站引水壓力鋼管施工現場為實例，研究取消伸縮節后焊接對引水壓力鋼管施工的影響，分析了兩種方案在焊接過程中的變形規律，分別用經驗公式和理論計算出兩種方案焊接時的橫向和縱向收縮量，然後分析收縮量對安裝焊接過程的影響，選擇出最佳安裝方案。
  20. Gangxing ultrasonic co., ltd., is a large - scale enterprise producing ultrasonic washing machine and ultrasonic plastic welding machine with a history of 20 years. it has brought up a technician team with exploiture, design and manufacture in integration

    港星超聲有限公司是一家生產超聲波清洗機和塑料焊接機的大型企業， 1984年成立至今，經過港星人二十年的不懈的追求與探索，造就了一批集開發、設計、製造於一體的技術人才隊伍。
分享友人
分享到 Line

分享到臉書