焊接加工 的英文怎麼說

中文拼音 [hànjiējiāgōng]
焊接加工 英文
welding fabrication
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  2. The comprehensive effect of partial acidlity of working medium, flowing status of fluid, nocuous material in atmosphere, together with the overlong usage, largely increased the corrosion rate and caused the leakage

    結果表明，泄漏的主要原因是焊接缺陷導致焊縫區發生縫隙腐蝕，而工作介質的局部酸性、流體的流動形態、大氣中有害物質、溫差應力等綜合作用，加上使用期過長等加劇了腐蝕，導致該塔泄漏。
  3. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  4. Meixing electronics factory is major in the vacuum tube stereo power amplifier, which is located in the nanhai city ， owned a workhouse over 1300 square meter, with five plant, they are box, seal and transformer circling 、 debugging & check, we also have the machine process, such as milling machine 、 punch 、 drill press 、 electric welding 、 matrix 、 incision machine, and radio tube test machine. we have realize the product line manufacture, the monthly whole output is over 200 sets

    美星電子是一個專業製造真空管身歷聲功率放大器的加工廠，位於廣東南海市黃岐工業區，擁有廠房一千三百平方米，工廠分機箱加工、焊接組裝、變壓器繞制、煲機老化、調試檢測五個車間，機械加工設備擁有銑床、沖床、創床、鉆床、電焊、模具製作、切割等二十多臺，電子管及整機檢測調試儀器十餘臺，該廠實現了配套設備、流水作業，每月可生產膽機二百臺以上，可謂中國專業生產膽機最大規模的工廠。
  5. In order to increase productivity, for big size tank welding, saf propose plasma plus tig double torch solutions, welding speed is 30 % to 50 % higher than single plasma torch welding

    為增加焊接生產的效率，對于大尺寸工件的環縫何縱縫焊接， saf採用等離子tig雙槍焊接工藝，焊接速度比單等離子增加30至50 。
  6. And is it the same as under radiation heating ? do the special electric and magnetic fields produced by bpec accelerate atom diffusion ? understanding the above questions fully is a key to expose the mechanism of pecht

    在脈沖大電流加工過程中原子是如何擴散的，與一般的加熱燒結、焊接是否一樣，脈沖大電流形成的特殊電場及磁場是否對原子的擴散有大的推動作用，弄清這些問題成為進一步揭示脈沖大電流熱加工機理的關鍵。
  7. In this paper, three unique models were designed to research atom diffusion at interface, contacting line and joining point under bpec heating and compare with it under radiation heating in order to find out if bpec speed atom diffusion. the first model was aimed to research atom diffusion at interface under bpec heating. experiment condition of bpec diffusion welding sheet cu and ni : direct diffusion welding, at a pressure of l0mpa, welded at 750 ~ 900, with heat rate of 200 ~ 400 / min for 10mm, on / off of 6 / l ~ 48 / 8, with die or not, vacuum of 6pa

    本文設計出三種樣品預構件，研究脈沖大電流加熱條件下片狀材料、線狀材料和球形顆粒之間的原子擴散過程，弄清脈沖大電流加熱條件下原子擴散與一般燒結和焊接過程中原子擴散的區別，以證實特殊的電場和磁場是否對原子的擴散有推動作用，揭示脈沖大電流加熱條件下原子的擴散過程，探索脈沖大電流熱加工技術快速高效的原因。
  8. Pulse electric current heat treatment ( pecht ) developed by sodick, ltd., of japan, is a recently developed material processing method which consists of spark plasma sintering and welding, plasma activated sintering and welding, big pulse electric current ( bpec ) diffusion welding etc. the following are basic merits of pecht : rapid heating and cooling ; short sintering or welding time ; lowering sintering or welding temperature

    脈沖電流熱加工（ pulseelectriccurrentheattreatment ，比如燒結，焊接等）是九十年代發展起來的一種材料快速制備新技術，它包括放電等離子燒結與焊接、等離子活化燒結與焊接、脈沖大電流擴散焊接等。它具有升溫、降溫速度快、能在較低的溫度下燒結或焊接以及時間短的特點。
  9. From the design of patterns to the choice of raw material, and through unique spraying and computer carving craft, welding and minute processing technology of professional technicians ; jiashide products are leading in the pattern, quality, technology and style, which is the first choice of numerous star hotels, high - grade buildings and luxurious residential houses

    佳仕得產品從款式的設計到原材料的精選，再通過獨特的噴塗噴砂和電腦雕花工藝結合，專業技師焊接及精細加工技術，無論在款式上還是質量技術和風格上均能處于引領潮流的地位，是眾多星級酒店高檔樓盤和豪華家居之首選。
  10. Metal fun tech is proficient in metal processing technology and assembly technology, and is particularly adept at sheet metal, welding, and finishing technologies

    金屬加工技術和組裝技術是我們的特色，特別是薄金屬板及焊接加工，精加工技術擁有自信。
  11. Co2 laser processing equipment for joining

    二氧化碳激光加工機焊接加工用
  12. Yag laser processing equipment for joining

    激光加工機焊接加工用
  13. Specification for the qualification of welding fabricators

    焊接加工人員資格鑒定規范
  14. Manufacturing processes joining - part 7 : joining by soldering or brazing ; classification, subdivision, terms and definitions

    連接加工工藝.第7部分:釬焊或銅焊連接.分類細分類
  15. Yag laser processing equipment for joining yag

    雷射加工機焊接加工用
  16. Responsible and organize set up and improve machinery and welding process

    負責和組織零件焊接加工工藝、切削加工工藝方案的確立。
  17. We excel at processing brass bronze and stainless steel and we perform cutting, bending and soldering in - house to a high level of quality

    本公司最擅長加工青銅，黃銅，不銹鋼，高品質的切削，彎曲，焊接加工。
  18. Moreover, we perform integrated production of everything from raw material selection through bending, pressing, welding, surface treatment and assembly

    採用素材彎曲加工沖壓加工焊接加工表面處理組裝加工為一體的生產流水線。
  19. This system can be used in other plane welding when working with the corresponding jig and rational welding craft arrangement, and this makes numerical welding machine becomes more efficient and flexible by changing nc codes according to different welding path and resolves the contradiction between process automation and process cost in some extent

    通過配合相應的夾具，合理的焊接工藝安排順序，該系統可以應用於其他平面焊接加工場合，數控焊機可以並根據焊接軌跡及時更改加工代碼，提高設備的焊接適應性和焊接效率，一定程度上解決了自動化成本和加工效率之間的矛盾。
  20. This paper discussed the total process of fabrication for big diameter vertical heat exchanger, including mostly tubesheet machining, technics request of tubesheet piecing - up, and weld request of tubesheet - to - shell ; measure of machining for square manhole and measure of square manhole - to - shell weld for preventing distortion ; taking special machining technics arid check up method for request of plane degree and check up method upon tubesheet

    摘要介紹了大直徑立式換熱器的製造過程，主要包括管板拼接、加工的工藝要求以及管板與筒體焊接要求；同時對方形人孔的製作及其與筒體的焊接防變形等採取了一定的措施，對管板上端面平面度的要求採取了特殊的加工工藝及檢驗方法。
分享友人
分享到 Line

分享到臉書