焊接后熱處理 的英文怎麼說

中文拼音 [hànjiēhòurèchǔlǐ]
焊接后熱處理 英文
post weld heat treatment （pwht）
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 熱處理 : [冶金學] heat treatment; heat treating熱處理保護塗料 heat treatment protective coating; 熱處理車...
  1. Usages : exhaust pipes of aircraft, boiler covers, heat exchangers, boiler pipes, some parts that are impossible for heat treatment after welding or assembling

    航空器排氣管、鍋爐蓋罩、熱交換機、鍋爐用管、延展接頭等的焊接、接合后無法熱處理的零部件及設備。
  2. After a nationwide restructuring of colleges and departments in 1952, the department was renamed as the department of machine manufacturing, comprising 5 disciplines manufacturing technology, foundry technology and equipment, forging and pressing technology end equipment, welding technology and equipment, and etall. graphy and heat treatmento in addition, on the basis of the original power machinery teaching group, the department of power machinery was set up, having 3 disciplines : thermal electr

    1952年院系調整，更名為機械製造系，設機械製造工藝鑄造工藝及設備壓力加工工藝及設備焊接工藝及設備金相熱處理5個專業，並且由原動力組擴建成立了動力機械繫，正式設有熱力發電后改為鍋爐燃氣輪機汽車拖拉機3個專業。
  3. The necessarily of post - weld heat treatment of spherical tanks was emphasized

    強調了焊接球罐焊后熱處理的必要性。
  4. According to these, the paper put forward some countermeasures : select low carbon steel or low metal alloy steel with lower intensity, like 20r steel ; while welding, adopt strict craft measures with lower welding heat to input ; after jointing, proceed the whole hot dissolving on time ; control each welding joint with hardness hb 185 ; add 0. 25 % water into the liquid ammonia as decay eclipse ; enhance checking in operation, repairing equipment in time through regular interior and exterior checking

    針對上述原因提出了防止氨冷器類臨氨壓力容器產生應力腐蝕裂紋的對策：選用強度稍低，但抗裂性較好的低碳鋼和低合金鋼，如用20r鋼製造；焊接時應採用嚴格的工藝措施和較低的焊接熱輸入量；焊后應及時進行整體消除應力熱處理；控制焊接接頭各區硬度hb 185 ；在液氨中添加0 . 25 %的水作為緩蝕劑；在運行中加強檢查，及時進行停車檢修時的內外部檢查和定期檢驗。
  5. Methods of post weld heat treatment

    焊接后的熱處理方法
  6. The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine

    實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。
分享友人
分享到 Line

分享到臉書