焊接坡口 的英文怎麼說

中文拼音 [hànjiēpōkǒu]
焊接坡口 英文
welding bevel
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 坡 : Ⅰ名詞（地面傾斜的地方） slope Ⅱ形容詞（傾斜） sloping; slanting
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  2. Cracks have been found in the flange and web splices at groove welds in at least four bridges.

    至少在四座橋梁的翼緣板和腹板拼接坡口焊縫中發現了裂紋。
  3. These attachments were considered secondary components, so no weld quality control has been imposed on the groove weld splice.

    這些附連件被看作是次要的部件，所以在這種坡口焊接中沒有進行焊接質量控制。
  4. This paper describes the difference between the terms of groove and bevel in weld joints and condition in asme code translation

    本文敘述焊接接頭中術語剖口與坡口的區別和在asme規范翻譯中應注意的問題。
  5. This chamfering machine employs the principle of rolling shear to shear the edge of the steel plate according to the angel needed, to obtain the bevel for w - elding

    該倒角機利用滾剪原理，對鋼板邊緣按所需角度進行剪切，以得到焊接所需坡口。
  6. For all processes, the welding procedure specification ( wps ) shall contain a detailed cleaning procedure indicating joint preparation prior to welding

    對于所有焊接方法，焊接工藝規程都應詳細包含清除方法，說明焊前坡口的準備。
  7. The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection.

    第二種是產生於立柱翼緣與主梁翼緣連接處的坡口焊縫焊趾處的裂紋。
  8. A large number of these cracks occurred because the groove welded component was considered a secondary member or attachment.

    發生這許多裂紋是因為把這些坡口焊接部件作為次要構件或附件考慮。
  9. Weldability testing - method of y - groove cracking test

    型坡口焊接裂紋試驗方法
  10. Method of u - groove weld cracking test

    U形坡口焊接裂紋試驗方法
  11. Method of y - groove weld cracking test

    Y型坡口焊接裂紋試驗方法
  12. Attached to the nc heavy duty vertical lathe is an electrical follow - up device, which is specially designed for accurately machining welding grooves on non - circular thick cylindrical work of variable walls, cone - like work or unequal cone - like work

    摘要數控重型立車在非圓形變壁厚筒體，錐體，不等錐體上車削焊接坡口時，採用電氣隨動車削裝置加工，達到並提高了加工精度要求。
  13. At present, electric beveler developed by shanghai electric construction technology institute is one of the machines for pipe process, which widely applies to heavy industries like electric power, petroleum, chemical, shipbuilding and boiler manufachure

    本廠目前生產的電動坡口機是上海電力建設施工技術研究所研製的管道端面加工系列機具之一，它適用於我國電力、石油、化工、造船、鍋爐等製造，建設安裝行業管道焊接前管端焊接坡口加工。
  14. Groove length and shape : if the weld is longer or the the vacuum of groove is larger, the welding deformation will be larger

    坡口長度和形式：焊縫越長，焊接變形越大，坡口內空間越大，變形越大。
  15. “ subcontractor will be responsible for weld mapping all pressure boundary welds and attachment welds to pressure boundary pipe 。

    「分包商負責將管端切削至合適的尺寸、坡口加工和組對焊接。 」
  16. 4 double - welded groove joints shall have their root passes back gouged to sound metal on the reverse side before proceeding with welding on that side

    雙面焊接的坡口焊道，應在焊接前將該面底部焊道逆向刨削，直到其對面露出完好的金屬。
  17. Square butt welding

    形坡口對接焊
  18. Weld with shop beveled ends

    工廠加工坡口焊接
  19. The paper introduces single " u " groove welding procedure for stainless steel inner cylinder of multilayer high pressure vessel, opening up a new method for welding clading stainless steel vessel

    詳細介紹了內筒為不銹鋼的多層高壓容器外u形坡口的單面焊接工藝，從而為不銹鋼復合容器的焊接開辟了一條新途徑。
  20. Hull structure welding groove type and size

    船體結構焊接坡口型式及尺寸
分享友人
分享到 Line

分享到臉書