焊接工段 的英文怎麼說

中文拼音 [hànjiēgōngduàn]
焊接工段 英文
welding bay
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 段 : Ⅰ量詞（部分） section; segment; part; paragraph; passage Ⅱ名詞（姓氏） a surname
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  2. Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  3. Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    文摘:從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  4. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  5. Abstract : there are four phases and dozens of parameters in preheating flash butt welding technology used for great section workpiece ' s welding

    文摘:用於焊接大截面工件的預熱閃光焊工藝包括四個階段。
  6. The explosive welding specimen were also annealed in vacuum at various elevated temperature from 1000 to 1300. optic microscope, sem, tem and eds ( electron diffraction scattering ) techniques are applied to observe the microstructure and the element profiles of the welding interface and the interdiffused layer, reveal the interdiffused performance of alloy elements at elevated temperature, and analyze the structure and composition of the precipitated phases. moreover, the tensile strength of welding line with the two different techniques and various welding parameters were carried out

    採用金相、掃描電鏡、透射電鏡、能譜等多種實驗手段對焊接結合層的微觀組織結構、高溫下nb - 1zr與不銹鋼合金元素的互擴散行為，形成的互擴散層的成分、金相組織和擴散層中的析出相的相組成和相結構等，都進行了較為詳細的分析，並且對在不同工藝、不同焊接參數下焊接的nb - 1zr合金和不銹鋼的焊縫做了強度實驗研究。
  7. This accomplishment can promote the confirmation of welding technique from experimental qualitative seeking to data quantitative analysis and represent a new method of welding technique. it greatly improve the quality of welding, improve the validity of welding technical cards

    這一成果的實現，使焊接工藝的制定從定性實驗摸索階段提高到了定量計算且有理論依據的新階段，並給焊接工藝參數的制定提出了一種新的方法，可大大提高焊接質量，提高焊接工藝卡的正確性。
  8. Before apply the test, all the welding work of block or section should be finish and accepted by view inspection

    當片體、分段組立裝配焊接完工後，經焊縫外觀檢查合格后，就可進行角焊縫密性試驗。
  9. At the time of design, the measurement of dispersion and interaction impedance will be used as design verification and improvement. at the time of manufacture, the measurement will find the problems of the slow - wave structures in machining, weld and fitting

    在管子研製階段，對色散和耦合阻抗冷參量的測量可以起到驗證、改進設計的作用;在管子生產階段，通過測量可以及早發現慢波結構在加工、焊接、裝配過程中的問題，防止瑕疵品繼續流水作業，提高生產效率。
  10. ( 3 ) the weld of pe pipe ca n ' t be proof - test by undestroyed probing. pe pipe must be welded by auto fusion equipment and reduce the man - made factor to the minimum at the same time. the operator must be well skilled and highly responsible, who performs upon weld quality control regulations, and check up the weld strictly after fusion

    （ 3 ）聚乙烯管道連介面由於不能象鋼管焊口那樣通過無損檢測手段來驗證是否合格，所以一定要使用自動化程度高的連接機具，將人為因素降到最低，並要求焊工除了熟練的操作技術外還應具備高度責任心，嚴格執行連接施工工藝質量控制要點和有關操作要領，焊接完后採取必要的檢查驗收手段。
  11. The economic success of lab & pharma, s. r. o. is coined / shaped by products and service services such as construction, designs, design in addition to supply, engineering and measuring. one can even receive offers on qualification, units, rooms and industry as well as on turnkey with lab & pharma, s. r. o. in outstanding quality

    是一家令客戶滿意的生產商和服務商，該公司提供新型的、專門的產品，例如生產、製作，整理工，切斷、削減，鐵路，電子束焊接，產品、製品，食物、食糧、食品，輪胎成型、服裝批量生產，機械設備匯聚，部分、片段，資質、資格，質量，技術的，水，材料。
  12. Firstly, the assembly technology at millimeter - wave band was introduced and a common rule of bondwire ’ s influence to system performance was summarized through simulation method. as the performance of mmic is sensitive to its channel temperature, the optimum thermal design for power combiner was presented

    由於微組裝工藝質量對毫米波頻段的功率合成器電性能有很大影響，本文討論毫米波微組裝工藝，進而藉助電磁場模擬研究了金絲互連對傳輸性能的影響，並進行了焊接工藝實驗。
  13. Introducing the development situation of chinese shipbuilding & ship - repairing industry, reviewing the basic experience of the welding technology & equipment used for this industry more than 20 years in south china, then prospecting it ' s development direction and giving some suggestions for it

    摘要在概要介紹當前華南地區船舶行業發展態勢的基礎上，回顧了二十多年來華南地區船舶焊接工藝技術與裝備應用的基本情況，展望了今後一段時期華南地區船舶焊接技術的發展趨勢，並提出了有關改進建議。
  14. Some of them are equally matched to similar german products. combining advanced large - scale digitally controlled machines and special cold processing equipments with advanced hot processing, casting, welding and many special key technologies, zhenxing company enjoys much more advantages in manufacture than others in china

    3本公司不僅擁有一批先進的大型數控機床和專用的冷加工設備，而且同時還具備熱處理鑄造焊接等多種加工手段，掌握許多關鍵工藝的專有技術，在製造加工能力方面，本公司具有較大的優勢。
  15. Four sections of rigid frames are respectively welded and bored integrally to ensure machining precision of the above mentioned rigid frames

    四段框架整體焊接，整體鏜加工，保證框架的加工精度。
  16. The welding path recognition system was developed with delphi 7. 0 in the environment of windows2000, which functions include filtering, sharpening, binarization and edge detecting. the straight line and curve can be identified through hough transform and line approximation method and the results are saved for nc auto programming

    能夠對從ccd傳感器攝取的焊接軌跡圖像進行濾波、銳化、二值處理、邊緣檢測等圖像處理工作，並通過分別通過hough變換、直線段逼近演算法完成對直線和曲線的識別，最後保存結果為后續nc自動編程提供數據。
  17. On basis of numerical simulation, the optimized weling technological has been vadidated and adjusted by plane test, results show that residual stress of both ends welded in advance can be decreased by the interspace welded later, and decreasing effect is the most obvious in the 50mm range of the interspace ; for local heating, it is 60mm from the edge of heated area to decrease residual stress

    通過平板試驗得到了分段焊與局部加熱合理工藝參數，並在此基礎上，對轉輪的焊接殘余應力場進行了調整與控制，使葉片出水邊危險區域附近產生了較大的殘余壓應力，且轉輪整體的殘余應力水平低於轉輪材料屈服極限的三分之一。
  18. Campaigns were also launched to promote and publicise amendments to the factories and industrial undertakings ( safety officers and safety supervisors ) regulations, the factories and industrial undertakings ( gas welding and flame cutting ) regulation, the importance of rest breaks at work and the safety of working at height

    年內，我們再次舉辦這兩項計劃，並推出了多項活動推廣和宣傳有關《工廠及工業經營（安全主任及安全督導員）規例》的修訂、 《工廠及工業經營（氣體焊接及火焰切割）規例》 、工作休息時段的重要性及高空工作的安全。
分享友人
分享到 Line

分享到臉書