焊極 的英文怎麼說
中文拼音 [hànjí]
焊極
英文
welding electrode-
Arc welding equipment - part 11 : electrode holders
弧焊設備.第11部分:電極握桿Recommended practices for gas - tungsten - arc welding
鎢電極惰性氣體保護焊的推薦規范Specification for welding electrodes and rods for cast iron
鑄鐵用焊條和焊極規范Before repairing, basing on the actual working condition, concerning the weldability, stress and deformation issues, the scheme of the cold welding technology whose essential being gtaw, low temperature preheating, postweld hammer the welded seam was established
修理前,圍繞兼顧解決焊接性、應力和變形問題,結合實際施工條件制定了以手工鎢極氬弧焊、鎳基焊絲、焊前低溫預熱、焊后錘擊焊縫為要素的冷堆焊工藝。Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.
連接條和接線柱的焊接必須使極柱頂部和蓋子的鉛襯套與連接條環口或接線柱完全熔焊牢固。Welding consumables - determination of moisture resistance of manual metal arc welding electrodes by measurement of diffusible hydrogen iso 14372 : 2000 ; german version en iso 14372 : 2002
焊料.通過測量可擴散氫測定手工金屬電弧焊電極的抗濕Energizing the machine "start" switch places the machine in an automatic single cycle operation that completes the element assembly.
開動機器,進行一次自動循環運轉就完成極群組的鑄焊。Metal argon arc welding of red copper and low carbon steel
紫銅與低碳鋼的熔化極氬弧焊The plate lugs should be dry before they are immersed in hot liquid lead of the cast-on machine.
在極耳被浸漬到鑄焊機的熱鉛液中之前,極耳應是乾燥的。Slots in platens for projection welding machines
凸焊機電極平板槽子The puddle section for heavy duty batteries must be at least the thickness of the base of the poststrap.
重型汽車蓄電池極柱焊接部位至少要等於極柱底座的厚度。Electrode taper fits for spot welding equipment - dimensions
點焊設備電極錐度配合尺寸Specification for automatic resistance spot welding electrodes
汽車電阻點焊電極的規范Electrode taper fits for spot welding equipment. dimensions
點焊設備用電極錐形配合.尺寸Resistance spot welding. electrode holders. part 1 : tapper fixing 1 : 10
電阻點焊.電極夾頭.第1部分:固定錐度為1 : 10Gas metal arc welding of galvanized steel, 10 through 18 gage, in the as - welded condition, with or without backing
在焊接條件下有或沒有墊板10到18規格的鍍鋅鋼的氣體保護金屬極電弧焊Gas tungsten arc welding of galvanized steel, 10 through 18 gage, in the as - welded condition, with or without backing
在焊接條件下有或沒有墊板10到18規格的鍍鋅鋼的鎢電極惰性氣體保護焊5 all single - sided groove joints in nickel alloys, stainless steel and ferritic alloys containing more than two ( 2 ) percent chromium shall be welded using a gas tungsten - arc root pass with an inert gas back purge
鉻含量超過2 %的鎳合金、不銹鋼和鐵素體合金的單面坡口焊道用鎢極氣體保護焊,其根部焊道用惰性氣體反吹。Solder bar is made from high purity metal. by means of strict qualitg control the oxide and metallic and non - metallic impnrities and effectively minimized, the available high purity solder bar is with uniform and glazed surface good wetting and spreading ability after molten bright joint and minimum oxide residue after soldering. our product is suitable for wave and handwork soldering with high quality requirement
本公司生產焊錫條採用高純度金屬原料,在嚴格品管條件下,有效控制氧化程度以及金屬和非金屬雜質含量,焊錫條表面均勻光滑,純度極高,熔化后流動性好,潤濕性極佳,焊點光亮,氧化渣物極少發生,適用於高品質要求的各種波峰焊和手工焊。Specification for bare electrodes and rods for surfacing
堆焊用裸焊條和焊極規范分享友人