焊渣 的英文怎麼說
中文拼音 [hànzhā]
焊渣
英文
welding slag; welding spatter-
The results show that the slag series has strong capabilities of deoxidization, denitrification and dehydrogenation and is able to protect welds and obtain high quality welds
試驗結果表明,其渣系具有很強的脫氧、脫氮和脫氫能力,對焊道能起到很好的保護作用,可獲得高質量的焊縫。A kind of stainless steel flux - cored wire has been successfully developed, based on acid slag type system, by adding a bit of oxides and trace of deoxidizer, adjusting the fluidity of melting slag to increase shielding of the back weld
在酸性渣系的基礎上,通過添加少量氧化物,調整熔渣的流動性,並加入微量的強脫氧劑,以增強背面焊縫的保護,研製成功一種背面不充氬的不銹鋼打底單面焊雙面成形專用藥芯焊絲。Electric arc welding electroslag welding
電弧焊及電渣焊Electro slag pressure welding machine for reingforcing steel bar
鋼筋電渣壓力焊機Close examination of the plug welds showed the existence of herringbone patterns near the slag and voids in welds.
對塞焊焊縫的詳細檢查表明在焊渣及氣孔附近,焊縫中存在著人字型裂紋。Reduced ilmenite is a special product only use for welding electrode industry in china. in a word, it is a substitute of rutile sand
粵橋牌還原鈦鐵礦為深灰色礦粉顆粒,主要用於藥皮電焊條等焊接材料的造渣劑。Hence lack of fusion and slag would exist at the weld root and create a large initial crack condition.
因而未熔透及夾渣存在於焊縫棍部,並造成大的初始裂紋條件。Thus the fracture likely initiated from fatigue sharpened cracks originating from slag and void in the plug welds.
因此,斷裂可能是由於從塞焊焊縫內的焊渣和氣孔外形成的尖銳的疲勞裂紋而產生的。Slag, blowholes, and paint on unfused regions were observed at the welded junctions.
在焊接處看到了夾渣,氣孔及未熔透區的油漆。" ubridge brand " marble mostly to use in slagging powder with drug cover welding electrode. improve slag basicity, steady arc, increase surface strain. it also used on architecture industry
粵橋牌大理石粉為白色或淺灰色礦粉,主要用於藥皮焊條等焊接材料的造渣造氣劑,可提高熔渣堿度穩Railtech international is the world leader in manufacturing a wide range of railtrack products such as track maintenance equipment , conductor rails , insulators , rigid catenary systems, fasteners, ballastless track … our staple products being rail welding with the alumino thermic ( at ) method or electric flash butt welding
拉伊臺克國際有限公司是一家製造多種鐵道產品的專業化公司,產品包括鐵路養護設備、導電軌、絕緣子、剛性接觸網系統、扣件、無渣道床、等等… ,其中的主導產品是鋼軌鋁熱焊及閃光對接焊產品。Solder bar is made from high purity metal. by means of strict qualitg control the oxide and metallic and non - metallic impnrities and effectively minimized, the available high purity solder bar is with uniform and glazed surface good wetting and spreading ability after molten bright joint and minimum oxide residue after soldering. our product is suitable for wave and handwork soldering with high quality requirement
本公司生產焊錫條採用高純度金屬原料,在嚴格品管條件下,有效控制氧化程度以及金屬和非金屬雜質含量,焊錫條表面均勻光滑,純度極高,熔化后流動性好,潤濕性極佳,焊點光亮,氧化渣物極少發生,適用於高品質要求的各種波峰焊和手工焊。Application of electroslag welding in high bridge pier
鋼筋電渣壓力焊在高橋墩上的應用But there are some technical difficults for the welding of aluminium alloy such as some broken bits being easily found, a large welding distortion can happen easily, hard to distinguish the difference between the solid metal and liquid metal colour, hard to control the temperature, a lot of air holes can be seen in the welding line and so on
但是鋁合金熔化焊時的技術難點在於:焊接時易引起夾渣,焊接變形大,金屬的固態和液態的色澤不容易區別,焊接操作時控制溫度困難,容易產生氣孔等等。如果焊前清理工作不是很好,檢測氣孔往往超標。On the basis of the experiment, the reason that high strength 7a52 aluminum alloy produced the familiar defects such as hot cracking, porosity, slag patch, etc. in the welding was analyzed, and the preventive measures of every defect were adopted
摘要在實驗的基礎上分析了高強7a52鋁合金焊接時出現的常見焊接缺陷:熱裂紋、氣孔、夾渣等產生的原因,並對每種缺陷提出了預防措施。Use a blast cleaner or power tool to remove weld flux slag, weld metal spatters, weld flux fume deposits, rust and damaged paint film in welded areas
通過噴砂或電動工具除去焊渣、飛濺焊煙、銹跡和焊接部損壞的漆膜。When installation should be careful and remove the cutting edges, burrs or welding slags on the connecting flange, to avoid to damage the inner lining rubber
安裝時小心輕放,並且要清除連接法蘭上的尖角、毛刺或焊渣等,避免損傷內襯膠。Before the pump installation, it is necessary to remove the impurities in the pipeline thoroughly like welding slag and metal scraps lest they are sucked into the pump causing accidents when the pump starts
泵安裝前一定要徹底清除管路內的雜物,如:焊渣、金屬屑等,以免泵起動時被吸入造成事故。Wollastonite is also used as : protective slag in casting ; sillicon - steel ; electrode coating ; lagging material ; ceramic moulds and bonding agent for abrasives a filling agent in paper making, the trace mineral in the production of white cement and special electric ceramics
硅灰石還是模鑄硅鋼的保護渣,電焊條的塗料,陶瓷鑄模,生產研磨材料和靡輪黏合劑,造紙的充填劑,生產白水泥,製造特殊電氣陶瓷等不可多得的礦物原料。Range of use : cz2. 5 air shovel is used for clearing slag by electric welding, beveling groove. it also can do some shovelling and cutting on steel cast
使用范圍: cz2 . 5型氣才鏟適用於電焊去渣、去毛邊、去坡口,也可在鋼結物體、鑄件上進行少量鏟削。分享友人