焊縫厚度 的英文怎麼說
中文拼音 [hànfénghòudù]
焊縫厚度
英文
actual weld throat thickness-
Based on the 3d geometry vision, using java3d, for each of worktable and sine welding seam part of sheet, the ve modeling experiments achieve the construct of macrostructure, security virtual thickness and virtual guide based on error, and accomplish the space restriction of robot running. via the structured laser sensor ’ s getting three - dimension information, the experiments achieve the modeling of sine welding seam part of sheet by using programming
在立體視覺傳感系統獲得三維信息的基礎上，利用java3d建模技術，分別對工作臺、薄板正弦曲線焊縫工件進行建模實驗，完成了虛擬環境中宏觀環境模型的建立，並根據誤差建立了安全虛擬厚度和虛擬向導，完成了對機器人運動的空間約束;通過結構光傳感器獲得三維信息，編程實現對薄板正弦曲線焊縫模型的建立。Decrease the weld number as possible : choosing the right thickness of steel plate can reduce the rectification amount after welding
盡可能的減少焊縫數量：適當選擇板壁的厚度，可減少焊后變形矯正量。All the size of fillet welds k are the thickness of the wall except those marked
未注焊縫焊角高度k均為焊件中薄壁的厚度。Effective thickness of fillet weld
角焊縫有效厚度48Sonic new ideas and views were proposed, such as regulation on general welding procedure qualification and its method of application, welding procedure qualification between heat exchange tube and tube sheet assessmented by the thickness of fillet weld, and so on
本文還首次提出一些新思路、新觀點，如母材、焊材分類細則以及標準以外材料分類要有分類報告佐證；通用的焊接工藝評定規定及使用方法；換熱管與管板的焊接工藝評定是評定角焊縫厚度；氣瓶焊接工藝評定是兩個類型評定的結合，也可以分別評定。Weld positioning under load without installation, seam thickness of the seam thickness of not less than two - thirds of the design, not to exceed 8 mm, should not be less than 25 mm in length weld, located in welds inside
安裝定位焊縫不需承受荷載時，焊縫厚度不少於設計焊縫厚度的2 / 3 ，且不大於8 ? ，焊縫長度不宜小於25 ? ，位置應在焊道內.安裝焊縫全數外觀檢查，主要的焊縫應按設計要求用超聲波探傷檢查內在質量.上述檢查均需做出記錄The paper expounds how to find out the potential safe problems and unobvious defects, such as beyond - limit deflection in fixed girders for gantry bucket wheel stacker / reclaimer, by means of completely checking fixed girders, movable beams, geometric shapes of stiff and flexible supporters, metal thickness and welding and how to solve the safe problems and remove the defects
摘要通過對門式斗輪堆取料機固定梁、活動梁、剛性支腿、撓性支腿的幾何形狀、金屬厚度、焊縫狀況、聯接螺栓狀況進行全面檢測，發現門式斗輪堆取料機固定梁存在下撓超標的安全隱患和其他非明顯缺陷，從而對堆取料機的安全狀況有了全面的掌握，並根據檢測結論對固定梁下撓缺陷及時進行校正消缺，避免發生設備垮塌事故，保證了堆取料機的安全穩定運行。This paper takes advantage of numeric simulation technology to investigate the weld - line movement and formability of twb with the same property and different thickness, analyzes the weld - line movement in three different drawing ways with the same drawing depth, and shows the normal rule of weld - line movement in different drawing ways, and the relationship between the weld - line movement and formability of twb of different thickness
摘要本文利用數值模擬技術對相同材質差厚拼焊板的沖壓成形性和焊縫移動進行研究，分析了相同拉延深度、不同拉延方式下焊縫移動情況，揭示了不同拉延方式下焊縫移動的一般規律和焊縫移動量與差厚拼焊板成形性之間的關系。Brushed stripe coating to all areas such as corners. edges, welds. small brackets, bolts, nuts. rivet - s. and interstices, before spraying application of each coat, to ensure that these areas have at least the minimum specified film thickness
在塗抹新塗層前，應刷掉所有區域的麻紋，比如各角落、邊緣、焊接處、小托架、螺釘、螺帽、鉚釘和裂縫，保證這些區域至少達到價格的最低膜厚度。Based on the project of a new television tower in guangzhou, the blind - hole method is employed in this paper to measure the longitudinal and circular residual stress in the inner and outer surface of a steel tube
摘要以廣州新電視塔鋼結構工程用大口徑厚壁埋弧直縫焊管為對象，採用一種應用廣泛且精度較好的檢測方法盲孔法，對厚壁直縫焊管內外表面的殘余應力進行了檢測。When the welding current is added, the quality of heat of the arc will increase, so both the volume of molten puddle and the depth of arc crater will all increase, and the weld depth will increase when the weld is cooling
焊接電流增加時，電弧的熱量增加，因此熔池體積和弧坑深度都隨電流增加，所以冷卻下來后，焊縫厚度就增加。The welding speed have evident effection on weld depth and weld width, when welding speed is added, both weld depth and weld width will decrease, for the inputed heat per time is limited
焊接速度對焊縫厚度和焊縫寬度有明顯的影響，當焊接速度增加時，焊縫厚度和寬度都大為下降，這是因為焊接速度增加時，焊縫中單位時間內輸入的熱量減少。分享友人