焊道 的英文怎麼說

中文拼音 [hàndào]
焊道 英文
pass; welding bead
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 道 : Ⅰ名詞（道路） road; way; route; path 2 （水流通過的途徑） channel; course 3 （方向; 方法; 道理） ...
  1. The etched section also reveals that multiple weld passes were made over the top of the original submerged arc weld pass.

    從酸蝕斷面還可以看出：在原自動埋弧焊的上面覆蓋有多層焊道。
  2. The results show that the slag series has strong capabilities of deoxidization, denitrification and dehydrogenation and is able to protect welds and obtain high quality welds

    試驗結果表明，其渣系具有很強的脫氧、脫氮和脫氫能力，對焊道能起到很好的保護作用，可獲得高質量的焊縫。
  3. Using the heat of welding to vapour water, cooling rates are lowered on the weld bead and heat - affected zone

    利用焊接時的加熱使水汽化，不僅使焊道而且使熱影響區的冷卻速度減慢。
  4. Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  5. Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    文摘:從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  6. Seal the assistant who clears up machine being that one kind of new model is good be used for the stainless steel project, equipment, what be come into being black solders road, handles a simplicity when it can help your relaxed treatment argon arc soldering machine flow welding stainless steel, grab the head as long as using this machine to control touch choose clear up liquid saying that the surface is light in soldering clean, the black welding bead is immediately disappear, bright if new, hurt bright stainless steel surface face by no means, clear up the queen using wet fabric to clean again, outside, stainless steel not getting rusty, not being suffused with yellow, be quick, more beautiful, more economical than using acid - washing method speed such as cream and polishing

    焊縫清理機是做不銹鋼工程、設備的又一種新型好幫手，它可以幫助您輕松處理氬弧焊接機燒焊不銹鋼時所產生的黑色焊道，操作簡單，只要用本機操縱搶頭沾取清理液在焊道表面輕輕擦拭，黑色焊道即刻消失，光亮如新，決不傷害不銹鋼表面亮面，清理后再用濕布擦拭，不銹鋼表面不生銹、不泛黃，比用酸洗膏和拋光等方法速度更快、更美觀、更經濟。
  7. The fcaw process shall not be used for the root pass of single - sided joints

    藥芯焊絲電弧焊工藝不用於單面焊接接頭的根部焊道。
  8. 5 all single - sided groove joints in nickel alloys, stainless steel and ferritic alloys containing more than two ( 2 ) percent chromium shall be welded using a gas tungsten - arc root pass with an inert gas back purge

    鉻含量超過2 %的鎳合金、不銹鋼和鐵素體合金的單面坡口焊道用鎢極氣體保護焊，其根部焊道用惰性氣體反吹。
  9. Abstract : a cavity is made on both sides of weld bead

    文摘:在焊道表面兩側作一空腔。
  10. A cavity is made on both sides of weld bead

    在焊道表面兩側作一空腔。
  11. The back purge shall be maintained for a minimum of two passes

    至少對兩條焊道進行惰性氣體反吹。
  12. Backing weld before making main wel back weld

    打底焊道
  13. Temper bead annealing bead

    回火焊道
  14. Gmaw short - arc tack welds shall not be incorporated into the root pass

    熔化極氣體保護焊-短弧點焊焊縫不能與根部焊道合成一體。
  15. Cosmetic bead cover pass

    蓋面焊道
  16. Root pass root run

    根部焊道
  17. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  18. Weld positioning under load without installation, seam thickness of the seam thickness of not less than two - thirds of the design, not to exceed 8 mm, should not be less than 25 mm in length weld, located in welds inside

    安裝定位焊縫不需承受荷載時，焊縫厚度不少於設計焊縫厚度的2 / 3 ，且不大於8 ? ，焊縫長度不宜小於25 ? ，位置應在焊道內.安裝焊縫全數外觀檢查，主要的焊縫應按設計要求用超聲波探傷檢查內在質量.上述檢查均需做出記錄
  19. The gmaw short - arc process shall not be used for welding socket welds or the root pass of o - lets and branch connections

    熔化極氣體保護焊-短弧工藝不適用於承插焊接或出口和分支連接的根部焊道。
  20. Each pass shall be cleaned free of slag before the next pass is deposited. each weld layer shall be visually free of slag inclusions, cracks, porosity and lack of fusion

    每一層焊道都應在熔敷下一層焊道前清除熔渣。每一焊層都不得有可見的夾渣、裂紋、氣孔及未熔透現象。
分享友人
分享到 Line

分享到臉書