焊須 的英文怎麼說

中文拼音 [hànxū]
焊須 英文
wart
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 須 : Ⅰ動詞1 （須要; 應當） must; have to 2 [書面語]（等待; 等到） await Ⅱ名詞1 （胡須） beard; mustach...
  1. Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.

    連接條和接線柱的焊接必須使極柱頂部和蓋子的鉛襯套與連接條環口或接線柱完全熔焊牢固。
  2. To evaluate fracture instability, the total sum of stresses due to residual welding or rolling stresses, dead load, and live loads must be considered.

    計算斷裂失穩性時，必須考慮焊接或軋制殘余應力，恆載應力和活載應力之總和。
  3. The welding conditions should always be neutral or slightly oxidizing.

    焊接氣氛必須永遠保持中性或微氧化。
  4. Care must be exercised in attaching the lead wires to the soldering tabs.

    在往焊接接線片上焊導線時必須非常小心。
  5. The examination must occur within the seven ( 7 ) months prior to the scheduled date of your welding inspection examination or re - certification anniversary date

    此檢查必須在您預定參加之焊接檢驗考試或再次認證日期前七個月內進行。
  6. Our factory started manufacturing pressure - container in 1986. we have all the necessary equipment for manufacturing, such as press of 155t, polishing - edge, windingboard, sheering - board machine, aut - welding machine, and processing equipments

    1986年開始生產壓力容器，擁有生產壓力容器必須的設備；如1500t壓機，刨邊機，卷板機，剪板機及自動焊設備、加工設備。
  7. It is proved that the connection and steel frame with beam flange dog - bone reduced have superior behavior to the frame of conventional design and the brittle failure is avoided in the steel frame. and conditions of stress development in the dog - bone, and the reason of the brittle failure in the rigid connections is obtained

    了解了狗骨處應力發展狀況；探討了剛性連接發生脆性破壞的原因；並強調指出樑柱連接處焊縫的焊接質量，對能否發揮狗骨式削弱的作用，達到預期的設計目的是至關重要的，必須予以重視。
  8. The algorithm of image processing is the key. due to anomalous welding seam, the intensive arc light, random breaking of the bubble and gathering of the gas in the welding area, the seam images captured contain a lot of noise. in this case the noise must be removed and the welding seam is positioned accurately

    本系統的圖像處理部分採用了ccd攝像頭和視頻捕獲卡，圖像處理的演算法是最關鍵的部分，由於焊縫圖像並不是十分規則，而且在焊接時還會受到強烈弧光、飛濺和工件表面狀況的影響，因此在這種情況下，必須有效的排除干擾把焊縫的中心位置準確找出來。
  9. But the welding program is complicated and the construction is very difficult so that the welding deformation and welding quality should be seriously controlled

    轉子中心體與支臂連接採用工地組焊施工，可使轉子支架整體性能好，能夠保證轉子組裝質量，但焊接程序復雜、施工難度大，必須嚴格控制焊接變形和焊縫質量。
  10. 7 the completed visual acuity record must be presented prior to taking cwi examination

    參加焊接檢驗師考試前必須出示完整視力檢查報告。
  11. When welding be sure to wear hood and barricade the working area

    燒焊時必須戴上面罩並將工作區域圍起來。
  12. Closure flanges may be mechanically seamed or welded in place. gaskets or other sealing elements shall be used with closures, unless the closure is inherently leak proof

    封閉裝置凸緣可用機械方法或焊接方法洽當接合。除非封閉裝置本身是防漏的，否則必須使用墊圈或其他密封件。
  13. Specially for welding of thin and mid - thickness steel ; suitable for mag co2 welding of low carbon steel and low alloy steel inner wire feeder structure ; zx5 series thyristor dc arc welder ac arc welder with single phase moveable coil for sma mma welding ; suitable for welding low carbon steel, low alloy steel ; suitable for welding mid - thickness steel

    可用於所有牌號焊條的直接手工電弧焊接引弧容易，無須用戶調節可遠距離調節焊接電流，便於焊工操作焊機動特性好，性能柔和，電弧穩定焊接熔池平靜，飛濺小，不咬邊，焊縫成形美觀。
  14. Records of weld - repair locations must therefore be maintained, so signs of distress found during plant operation can be related to the original fabricated conditions and standards

    焊補位置的紀錄因此必須保存，所以在工廠運行過程中，故障發生的信號可能與原始的製造條件和標準有關。
  15. The necessary protective clothing and equipment for specific jobs e. g. oxy - welding and cutting, electric welding must be worn while this work is being carried out

    特殊工種需要著裝不同的防護服。例如，氧氣焊接與焊割、電焊工工作時，必須穿著特殊的防護服。
  16. A supervisor of a testing laboratory was sentenced to 80 hours of community service for submitting false worksheets to facilitate the issue of welder approval test certificates to workers of a welding subcontractor for a government department project

    一名化驗所主任，提交虛假的工作記錄，促使化驗所向政府部門工程鍛焊分判商的工人發出鍛焊測試合格證書，被判須履行八十小時社會服務。
  17. Operators conducting operation with fire danger like electrical welding and gas welding or operators for automatic fire control system, must hold relevant certificates and strictly observe operation rules on fire control safety

    進行電焊、氣焊等具有火災危險的作業的人員和自動消防系統的操作人員，必須持證上崗，並嚴格遵守消防安全操作規程。
  18. 8 temporary backing bars and temporary rings must match the chemical composition of the base metal being welded

    臨時支桿和箍必須與相焊的母材金屬的化學成分匹配。
  19. All tubes to be tightly expanded into tube sheet or welded ( into tube sheet )

    所有的管子都須與管板脹緊或焊牢。
  20. Apply flux to outside of tube and inside of solder cup. surfaces to be joined must be completely covered. use flux sparingly

    在管道外面和焊接埠內側塗上焊劑。需要連接的表面必須完全覆蓋焊劑。要節約使用焊劑。
分享友人
分享到 Line

分享到臉書