無約束變數 的英文怎麼說

中文拼音 [wúyāoshùbiànshǔ]
無約束變數 英文
unrestricted variable
  • 無 : 無Ⅰ動詞（沒有） not have; there is not; be without Ⅱ名詞1 （沒有） nothing; nil 2 （姓氏） a surn...
  • 約 : 約動詞[口語] （用秤稱） weigh
  • 束 : Ⅰ動詞1 （捆; 系） bind; tie 2 （控制; 約束）control; restrain Ⅱ量詞（用於捆在一起的東西） bundle;...
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 約束 : keep within bounds; restrain; bind; bound; boundage;tie; restraint; restriction; engagement; repr...
  1. Optimal design with three variables is then done to the elbow - bar mechanism of the mp1040b moulding machine by utilizing the method of punishing function for constraint problems and variational scale for unconstraint problems. the optimal target function is the maxium of gradient in one work travel for the moulding plank of the elbow - bar mechanism. the result shows that the maximal gradient of moulding plank in one motion period declines by 25. 7 after optimization, and the angular acceleration of the bottom moulding plank decreases greatly

    動力學分析中，各構件的質量和轉動慣量是通過pro / engineer軟體，先建立各個構件幾何模型而求得；然後，利用解決約束問題的罰函數法和處理無約束問題的變尺度法對mp1040b型模切機肘桿機構進行三個設計變量的優化設計，優化目標函數為肘桿機構的下模切板在一個工作行程中達到的最大傾斜程度；通過優化設計，模切機肘桿機構的下模切板在一個工作行程中的最大傾斜程度降低了25 . 7 ，其角加速度明顯減小，提高了模切機動力學性能。
  2. The connection between the torque and the polarized charges is established. on the base of mathematical model of torsional effect, using multivariate unrestrained nonlinear optimization method, we research cutting angles and parameters of crosssection to get best torsional sensitivity

    在建立石英晶體扭轉效應模型的基礎上，應用多變量、無約束非線性優化方法對于晶體切型、截面形狀等參數進行了優化，以獲得最佳扭轉靈敏度。
  3. Optimal periodic control with the lowest operational cost by limiting total substrate discharge mass was studied. through adding new state variable and using supplement functions, the problem with restriction conditions was converted into nonrestriction problem. in addition, the dynamic searching method of optimal step coefficient was developed to modify the conventional gradient method, consequently the calculation problem of the multivariable optimal periodic control was able to be resolved better. it was found that the operational costs of optimal control under various initial states are distinctly different. a new concept of optimal control under optimal initial state was presented. it is pointed out emphatically that to the treatment system without optimal control condition, the suboptimal control with extensive practical value can be realized according to the results of optima control

    著重研究了在限制有機物排放總量時，使其運行費用最低的最優周期控制問題.通過增加新的狀態變量和用補償函數法，將本課題的有約束條件問題化為無約束條件問題，並提出了最優步長參數的動態搜索法來修改傳統的梯度法，從而較完善地解決了多變量最優周期控制的計算問題.研究中還發現了不同初始條件下最優控制所需要的運行費用也大不相同，進而提出了最優初始狀態下最優周期控制的新概念，這對保證出水質量的同時進一步降低污水處理成本來說具有更重要的意義.本文還強調指出：對于尚不具備實現最優控制條件的處理系統，可根據最優控制的研究結果實現具有廣泛實用價值的準最優控制
  4. Based on the genetic algorithm ' s global searching capability with probability regulation and euclid ' s space distance metric to settle multi - objective, the algorithm that integrates multi - objective ' s decision - making into the modified genetic algorithm to solute the optimal model with discrete variables and multi - objective is proposed. during the algorithm ' s design, the euclid ' s space distance metric is proposed to transform the multi - objective problem into single objective problem. and some modified measure to fitness function and crossover probability and mutation probability are used to improve the performance of the algorithm and avoid premature convergence

    演算法設計過程中，利用歐幾里德空間距離準則和罰函數法，將含有約束條件的多目標規劃問題轉化為無約束的單目標優化問題；針對簡單遺傳演算法出現的早熟，構造隨進化代數動態調整適應度的適應度函數和隨個體適應度自適應調整的交叉、變異概率；提出比例選擇與精英保留策略相結合的選擇、兩點交叉和簡單變異的改進遺傳演算法。
  5. A bearing surface transmits the interaction between an arch dam and its foundation, the strength of which directly affects the constraint of the bedrock to the dam, and thus affects the stress and deformation of the dam. the influence is studied in this paper with nonlinear finite element method, as an example, for a high arch dam in design. the results show that the influence on stress is only limited within the local area near the bearing surface, larger on the maximum principal tensile stress than on the principal compression stress, and the decrease of the strength does not cause unlimited increase of the maximum stress. the influence on the displacement of the top of the dam is smaller than that of the bottom of the dam, especially the relative downstream displacement. at the lower strength of the bearing surface, the relative downstream displacement at the bottom of the dam increases with the decrease of the strength

    建基面是傳遞拱壩和基巖相互作用的紐帶，它的強度直接影響基巖對壩體的約束，從而影響壩體的應力和變形.採用非線性有限單元法，以設計中的某高拱壩為例，分析建基面強度對壩體應力和變形的影響.結果表明建基面強度對壩體應力的影響僅限於建基面附近的局部范圍，對最大主拉應力的影響要大於對最大主壓應力的影響，建基面強度的降低不會無限地增大壩體的應力數值；建基面強度對壩頂位移的影響較小，但對壩底位移（尤其是順河向相對位移）的影響較大，當建基面強度較低時，壩底順河向相對位移隨建基面強度的降低而增大
  6. Abstract : this paper developed time domain integral constraints on error response for siso feedback control systems caused by nominal plant ' s near cancellation of stable pole - zero near the j - axis. these integral constraints should be satisfied by any feedback control systems. these integral constraints give new insight into the inherent trade - offs. it will result in the settling time longer or the infinite norm of the error response larger when there are near cancellations of stable pole - zero near the j - axis. hence, when feedback control systems are designed, it is necessary to avoid the compensator ' s poles and zeros nearly cancelling the nominal ' s zeros and poles ( even if these poles and zeros are stable )

    文摘:導出了單輸入單輸出反饋控制系統誤差響應基於名義系統穩定的零、極點近似相消的時間域積分約束，此積分約束是任何反饋控制系統均應滿足的.這一約束給出了單輸入單輸出反饋系統固有折中的新的觀點.名義系統穩定的零、極點近似相消的存在導致反饋控制系統的調節時間延長或者誤差響應的無窮范數變大.因此，在反饋控制系統設計中，盡量避免補償器的零、極點與名義系統的極、零點近似相消（即使這些零、極點是穩定的）
  7. First because of the change of the number of material between supply and need, we could n ' t know exactly situation before it happened, so we build the maths model of alot material with fuzzy constrained which accords with the fact and solves the problem better

    首先以供需雙方的物資數量經常變化，無法事先準確知道為背景，建立了帶模糊約束的物資分配問題的數學模型，這一模型符合實際，較好的解決了問題。
  8. It is known that the vip can be reformulated as an unconstrained minimization problem through the d - gap function

    我們知道，通過廣義d -間隙函數，可以將變分不等式問題轉化為一個無約束極小化問題。
  9. The control system of wind turbine includes individual control and group control. according to the control process and main technical parameter, the paper accomplishes the control system structure design and input - output system design. this paper also deeply analyzes the operation principle of the whole control system and the relation between each part in order to realize the no - person automatic operate

    本文以1mw變槳距風電機組為研究對象，根據其主要技術參數及控制工作過程，對其單機控制系統的構成進行了設計，闡述了輸入輸出介面和各個控制環節的運行原理及其相互之間的聯系與約束關系，從而實現在無人值守的條件下，實現多種預定的控制目標，並在此基礎上探討其更廣泛的適應性及實用性。
  10. Furthermore, it was the first time to make a systemic analysis and study to the motion rule and affected factors of this kind of transformer. with the applications of relative polar method and equal view angle method, the transformer that satisfies the requirement of transmission rate and output motion is synthesized. thus, an original non - frictional stepless speed regulator with a 1. 5kw input power, a 1500 rotation speed, a constant150output rotation speed and a maximum 300 output rotation speed was achieved

    在此基礎上利用相對極點法和等視角法按傳動比及輸出運動的要求對轉換器進行了綜合，得出了輸入功率1 . 5kw ，輸入轉速1500 ，額定輸出轉速為150 ，最大輸出轉速300的新型的非摩擦式無級變速器的基本尺寸參數並應用adams軟體對其進行了優化；最後對該非摩擦式無級變速器進行了過約束分析，提出了新型的非摩擦式無級變速器無過約束分析的機構運動副的配置方案。
  11. With merit function, the origin problem can be conformed to unconstrained or constrained minimization problems

    利用merit函數的極小化變形可分為無約束和約束兩種類型。
  12. ( 4 ) penalty function method is used to import the constrains into the objective function

    （ 4 ）本文利用「懲罰函數法」將約束問題轉變為無約束問題。
  13. The solving steps are as follows : the field is divided into three regions by the cylindrical surface of the finite - length cylinder and the location of the delta - coils. because " the surface current source is placed at the interface, the non - homogenous restricted equation on the magnetic vector potential is transformed into the homogenous helmholtz equation. by using the method of separation of variables to solve equation and according to the interface conditions and the condition at infinity to determine the unknown constants, the expressions for the magnetic vector potential of the three regions are solved out

    在求解過程中，假定放置式圓柱線圈是由無窮多個對稱圓環線圈密饒而成，首先求解含有有限長磁芯的通電對稱圓環線圈的電磁場：以有限長圓柱磁芯的側面和圓環線圈所在圓柱面為分界面將場域劃分為三個小區域，由於場源放置在內邊界面上，使得關于矢量磁位的非齊次約束方程轉化成齊次亥姆霍茲方程，利用分離變量法求解，根據分界面鄭州大學碩十研究生畢業論文摘要條件以及無限遠條件確定待定常數，從而得到各場區矢量磁位的表達式。
  14. In order to assure that the stress and strain state of structure is secure, the author analyses respectively the objective functions of the reasonable finished state and buckle - cable adjusted phase ; thus, the optimized model based on fga is framed. finally according to the example, the computation datum are compared with the iterative forward analysis method and the optimal control theory. the result shows that this method can be used conveniently and meet the construction and design precision

    為了滿足大跨度鋼管混凝土拱橋施工的安全性與成橋預期的內力狀態和拱肋線形，本文結合工程實例，分別對合理成橋狀態和扣索索長調整的目標函數的確定進行了分析，將一組多變量、多約束的最小化問題無約束化，從而建立起適合於該問題的遺傳演算法優化模型，將其計算結果分別與迭代前進法和隨機最優控制理論進行了比較；結果表明，採用該方法編制的基於結構計算的遺傳優化程序操作靈活，能很好的滿足施工和設計要求。
  15. This algorithm improves confidence in se by estimating parameters and states at the same time. simulation results on test power systems which range in size from 4 to 118 buses, have shown the virtues as follows : getting unbiased estimation without detecting and identifying bad data in measurements ; solving state and parameter estimation for power system with good convergence and excellent robust property ; increasing the numbers of iterations a little bit with the test systems expanded ; estimating many transformer taps simultaneously and remaining the main state estimation ; keeping the estimated relative error within + 0. 1 % and processing efficiently equality constraints and ill condition with polynomial complexity

    對ieee ? 4 118節點系統和廣西主網進行的模擬結果表明： l1范數估計具有不良數據拒絕特性，當量測量中存在不良數據時，該演算法在不經檢測和辨識不良數據情況下仍是無偏估計，具有良好收斂性，所需迭代次數隨著問題規模擴大而增長極小；能夠同時估計多個變壓器抽頭，並保持狀態估計主體；在滿足可觀測性條件下，估計的相對誤差保證在0 . 1以內；能夠有效處理等式約束和病態條件，並具有多項式時間性。
  16. The rbf network has a better performance, and better forecasting accuracy. then mathematical model of substation voltage / var control is constructed, the squares minimization of voltage differences as target, also considering requirement of voltage and power balance, taking it into consideration that the magnitude constraint of transformer ratio and compensating capacitor, also that constraint of operation times of one day transformer tap and capacitor switch

    因此提高了學習性能，具有較好的預測精度。然後，建立變電站電壓無功控制的數學模型，考慮電壓的調壓要求和無功功率平衡，計及變壓器變比和並聯補償電容的上下限約束，變壓器分接頭和電容器允許的日調節次數的限制，以電壓偏差的平方和最小為目標函數。
  17. Motivated by the above results, the third part of this paper considers the equivalence problems that every stationary point or kuhn - tucker point is an efficient solution. we define i - quasi - invex vector function., i - strictly quasi - invex vector function and kt - i - strictly quasi invex vector function, and derive the above equivalent condition for unconstrained or constrained multiobjective programming

    於是，在本文的第三部分，我們定義了類不變擬凸、類嚴格不變擬凸、 kt -類嚴格不變擬凸的向量值函數，並且在無約束或約束多目標規劃中，獲得了每個駐點（或k - t點）是有效解的等價條件。
  18. In addition to interface and base class constraints, some special constraints are defined such as the parameterless constructor constraint, which requires that type arguments have a default constructor a public parameterless constructor

    除了介面和基類約束外，還定義了一些特殊的約束，例如無參數構造函數約束，它要求類型變量具有一個默認的構造函數（公共無參數構造函數） 。
分享友人
分享到 Line

分享到臉書