焦外光度計 的英文怎麼說

中文拼音 [jiāowàiguāngdùjì]
焦外光度計 英文
extrafocal photometer
  • 焦 : Ⅰ形容詞1 （物體受熱失去水分 呈現黃黑色並發硬、發脆） burnt; scorched; charred 2 （著急） worried;...
  • 外 : Ⅰ名詞1 （外面） outside; external side 2 （外國） foreign country 3 （以外） besides; beyond; in ...
  • 光 : Ⅰ名詞1 （照耀在物體上、使人能看見物體的一種物質） light; ray 2 （景物） scenery 3 （光彩; 榮譽） ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 焦外 : afocal
  1. By comparison and analysis of the auto lensmeter used in domestic and abroad, optics theory and foci adjustment method are discussed, the formulation of diopter of glasses is given

    本文通過對國內外同種類型設備的比較和分析，給出了數字查片儀的光學原理和調焦原理，推導了鏡片屈光度的計算公式。
  2. The super resolution effect of sb layer super resolution structure is also investigated with near - field scanning optical microscope. in addition, a rigorous three - dimensional ( 3d ) optical electromagnetic finite - difference time - domain ( fdtd ) model for analysis of a sil system is detailed. in order to accurately analyse sil model, a new method of setting a focused gaussian beam source in fdtd grids is presented

    此外，本文還建立了對sil系統光傳輸特性進行模擬的時域有限差分程序，提出一種在fdtd模擬的離散空間設置會聚高斯光源的新方法，並模擬了會聚高斯光束在sil系統中的傳輸，研究了sil在不同離焦情況下底面出射光場幅度及光束半徑的變化規律，為sil存儲系統的優化設計提供了理論依據。
  3. Firstly, the system is divided into many modules according to different point of view ; secondly, to the hardware equipment - vidicon, lenses, revolver, shield and decode device, their principle of work has been explained ; thirdly, according to image identification experience and other indexes of the system, the focus of the lenses and relative aperture are calculated, and the type of the camera is confirmed, at the same time, the energy of infrared lamp is also computed in the thesis ; at the same time, synthesis control box is devised

    首先，按照角度的不同，將系統劃分成許多模塊。其次，對硬體設備? ?攝像機，鏡頭，雲臺，防護罩，解碼器等的工作原理進行了闡述，再次，以人的成像辨認的經驗判據為依據，結合系統的其它指標，設計計算出鏡頭的焦距f 、相對孔徑d ，同時確定攝像機的型號，並計算出紅外燈光源。最後，對綜合控制箱進行設計，指出了設計的意義，實現的功能，並附上了綜合控制箱的外形圖。
  4. Firstly, optical trigonometry measurement principle and wok principle of linear ccd are introduced, which are based on to design optical focusing and imagery system with he - ne laser instrument as illuminant. secondly, peripheral circuit of linear ccd is designed in theory and experiment. finally non - contact thickness measurement instrument is constructed, using ccd as photoelectric transformation element and microprocessor as the controller

    本文首先介紹了光學三角法測量原理，並對線陣ccd的工作原理進行了研究，以此為基礎採用氦氖激光器為光源，設計了光學聚焦及成像系統，對線陣ccd外圍電路的設計進行了理論設計和實驗研究，最後設計了以ccd為光電轉換元件，以微處理器為控制核心的非接觸式厚度測量儀及其系統。
  5. As far as input coupling devices concerned, we design a feasible taper coupler by means of the theory of waveguide coupling and outside cavity waveguide laser and make decision of the sizes of the lens and the taper coupler, and the relative distance of them. the focus of the lens is 65mm and the radius is 5mm. the length of the taper coupler is 15mm, and the radiuses of the input and output ends separately are 17mm and 0. 65mm

    在輸入耦合器方面，藉助于波導耦合和外腔式波導激光器的相關理論，設計了工藝上可行的錐型耦合器，確定了透鏡、耦合器的尺寸以及耦合器與透鏡的相對位置：耦合透鏡的焦距為65mm ，直徑為srnm ，耦合器的長度為15mm ，輸入端直徑為17mm ，輸出端直徑為0
分享友人
分享到 Line

分享到臉書