熔料拉制 的英文怎麼說
中文拼音 [róngliàolāzhì]
熔料拉制
英文
melt-pulling-
In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed
本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。Therefore, in this paper, two directional solidification methods, czochralski method and electron - beam floating zone melting method, were used to obtain such material. the directional solidifition microstructures of si - tasi2 system was performed using neophot - 1, amray - 100b sem and jem - 2000cx tem analysis technique
本文採用切克拉斯基法（ cz法）和電子束區熔法（ ebfzm ）兩種定向凝固方法制備該共晶自生復合材料；藉助金相技術、電鏡技術、圖象處理技術等多種分析測試手段，考察了si - tasi _ 2共晶定向凝固組織和及其相應的工藝規范。Servo control computer system / microcomputer universal testing machines, ozone tester, compression flexometer, computer hdt / vicat tester, digital impact tester, melt flow indexer, moving die rheometer, mooney viscometer, lamination of pvc plastic press tester
伺服控制電腦系統微電腦式拉力試驗機，耐臭氧機，橡膠壓縮生熱試驗機，塑料用維卡熱變形，數位沖擊試驗機，塑膠熔體流動速率機，無轉子密閉膜腔硫化儀，門尼黏度試驗機等等。Before plastic optical fiber widespread application, each kind of plastic optical fiber coupler must be used surely, at present the important method to manufacture the plastic optical fiber coupler is fused elongated taper. if adopt this kind of method, the conversion efficiency between the core modes and the cladding modes is low. one of the methods to solve that is
在塑料光纖廣泛應用之前必然運用到各種塑料光纖耦合器，目前熔融拉錐法是制備塑料光纖耦合器的重要方法，然而此種方法存在纖芯模與包層模的轉換效率比較低的問題，解決這問題的一種方法是對塑料光纖進行熱預拉錐。Pdlla / ha composite fibers were produced by melt spinning, and the choices of the process parameters such as temperature, revolving speed and drawing speed etc were discussed
選用熔融紡絲法制備pdlla ha復合纖維，探索了熔融紡絲過程中溫度、擠出機轉速、拉伸速率、加料速度和冷卻速率等一系列工藝參數的選擇及其影響因素。分享友人